What is the cause of water leakage in an automatic washing machine

If it is a washing machine with a wave wheel:

1. If it is a washing machine, it may be that the drain pipe is not fixed and rotten, and it is more likely to appear in the machine for more than two years.

2. The overflow pipe is worn out, and when you open the back cover, you can see that a transparent pipe mostly appears as an old machine.

If it is a drum washing machine.

1. If it is a drum washing machine, it is possible that the laundry detergent or other high-foaming laundry detergent or liquid used in 1 may leak from the laundry detergent dispenser box.

2. The gas collector valve at the bottom of the outer cylinder is rotten.

It is also possible that the faucet is dripping or the floor drain is slightly clogged and causing an overflow.

The above are the most common small problems, with the eyes can be eliminated from the water source, regardless of the new machine or the old machine, they can't understand and can't find the after-sales service as soon as possible, water leakage is easy to cause a short circuit.

Extended information: Washing machine experts from the China Household Electrical Appliance Research Institute pointed out that the environment inside the washing machine is very humid, and after a few days of inactivity, a large amount of mold will grow. The longer it is used, the more opportunities there are for mold to grow inside.

After a washing machine has been used for a long time, if it is not cleaned in time, the water will slowly become muddy and the rinse will not be clean. Over time, it will cause contamination to the next laundry. If people use moldy washing machines to wash clothes for a long time, it is possible to produce cross-infection and cause various diseases.

One of the easiest and most effective ways to prevent mold is to leave the washing machine covered after washing.

Washing machines should be protected against fungal spores: The number of fungal spores in a fully automatic washing machine is more than that in a semi-automatic washing machine. Therefore, after washing clothes, you should empty the water in the washing machine in time, and open the lid to use a disinfection cabinet or clothing disinfectant if possible; Underwear is best washed by hand.

What are the causes of a water leak in a washing machine? Let's see how to solve it.

Common water leakage parts and causes of automatic washing machines:

1. From the front of the washing machine, if the right rear part leaks, it means that the connection between the drain pipe and the drain pump is not real, or the rubber connection pipe between the drain pump and the filter has a sand hole, a crack or the connection is unreliable, or it may be that the screws at the sealing place of the drain pump body are loose.

2. If the right front of the washing machine leaks, it may be that the filter bellows or connecting pipe has a sand hole, a crack and a poor connection.

3. The middle of the washing machine leaks in the front, the reason is that there is no fastening between the outer cylinder body and the front cover, that is, the screws of the outer cylinder buckle ring are loose, or the metal pressing plate connected by the rubber bellows is not firmly fastened with the outer cylinder, or the outer cylinder weld is not firmly welded, or the outer cylinder sealing ring is cracked.

4. The water leakage at the fork frame behind the outer cylinder is due to the improper assembly of the rubber sealing ring between the outer cylinder fork frame and the outer cylinder or the damage of the sealing ring. The outer cylinder fork can be removed, the seal can be reinstalled, or the seal can be replaced. When installing a new seal, the triangular raised side of the seal should be placed towards the fork frame when the seal is embedded in the shaft hole of the outer cylinder.

The causes and treatment methods of water leakage in automatic washing machines are as follows: Qiao Xiao.

1. If there is a rupture in the drain pipe itself, it is recommended to replace the drain pipe.

2. If the drain valve is not closed tightly or the drain valve is broken after being stuck by a foreign body, you can clean up the foreign matter at the drain valve port first.

3. It may be that the connection between the drain pipe and the washing machine is leaking, and it is recommended to reconnect it.

How to deal with water leakage in a fully automatic washing machine:

1. Drain the rubber bowl or rubber ring to remove the water leakage fault of the washing machine

The sealing ring (also known as the "oil seal") loses its elasticity, coupled with long-term operation wear, it is easy to cause a gap between the shaft and the oil seal of the washing machine, resulting in water leakage failure of the washing machine. Troubleshooting a water leak usually involves removing the water wheel, removing the shaft, then priing off the worn oil seal, and finally reinstalling it.

2. Washing bucket leakage: The water leakage fault caused by cracks in the washing machine barrel due to aging and other reasons is more intuitive. If the leakage is in the upper part of the washing bucket, it can be repaired by adhesive method, if the leakage is in the lower half of the washing bucket and the crack is relatively long, the washing bucket can generally only be replaced.

3. The spring elasticity is reduced, so that the compression between the water glue bowl and the drain port is not enough;

The path of the spring compression deformation is slightly deviated from the central axis of the spring, so that the derubber bowl cannot be pressed on the drain in the middle position. These all lead to platoons.

4. Water leakage caused by rupture of the drainage pipe: remove the back box board of the washing machine and observe whether the drainage pipe of the washing machine has obvious cracks and creases. In particular, the proximity of the pulley to the fan blade, the drain pipe and the tee joint, and the tee joint are prone to damage.

If the drain pipe and the tee joint are damaged and not serious, you can use the double Xunhuai pipe glue to glue, and carry out the drainage test ** whether it is effective, if the damage is serious, only replace the new drain pipe or tee joint.

5. The rubber sleeve of the dehydration shaft wave wheel is damaged or not tightly sealed; The rubber sleeve of the wave wheel itself is cracked or aged; The rubber sleeve of the wave wheel is not tightly adhered to the drain port of the dewatered outer barrel or is deglued during use, resulting in water leakage. In the event of the above problems, they should be repaired or replaced with new parts.

When it is an old-fashioned washing machine, it has been used for a long time, and it is also possible that the shell has deteriorated due to a long-term humid environment, as long as the leakage is plugged with sealing filler, the leak is welded, or the inner barrel is replaced.

If the fully automatic washing machine is leaking, the following measures can be taken to solve the problem:

Check the water pipes: First, check for loose or broken water pipes. If you find that the hose is loose or broken, you can use a wrench to tighten or replace the hose.

Check the washing machine drain: Check the washing machine drain for damage or blockage. If the drain is clogged, clean the drain or unclog it with a feed-through.

Check the washing machine door seal: Check the washing machine door seal for cracked or source tenant aging and replace the seal if a problem is found.

Check the washing machine filter: Check if the washing machine filter is clogged, and if the filter is clogged, clean or replace the filter.

Adjust the washing machine water level: If the washing machine water level is too high, you can adjust the washing machine water level so that it runs within a suitable water level range.

Seek professional help: If none of the above methods can solve the problem, you can seek a professional washing machine repairer to check and repair.

When a fully automatic washing machine leaks, you can solve the problem by checking the water pipes, drain pipes, door seals, filter elements and water levels, as well as seeking professional help.

If a fully automatic washing machine is leaking, the following steps can be taken:

1.First, immediately turn off the power and water inlet valves of the washing machine and stop using the washing machine.

2.Clean and remove clothing from the leaky area.

3.Check the bottom of the washing machine for water droplets or stagnant water, and if so, you can use a water pump or suction to pump the stagnant water clean.

4.Inspect the washing machine's water inlet, drain and power cord connections for loose or damaged connections, and reinstall or replace them if necessary.

5.Check that the door seal of the washing machine is intact and replace it if it is damaged.

6.Check the washing machine drain pump for blockages or malfunctions, and clean or replace it if necessary.

7.Before reactivating the washing machine, it is a good idea to double-check whether the above problems have been solved and make sure that the installation is firm and stable.

If the above steps still do not solve the water leakage problem, it is recommended to seek help from professional maintenance personnel.

The original cause of water leakage in the automatic washing machine is poor sealing of the water inlet nozzle, drainage pipe problems, foreign matter in the drain solenoid valve, loss of elasticity of the sealing ring, and aging of the washing machine.

1. The sealing of the inlet pipe mouth is not good.

At this time, it is necessary to check the water inlet pipe, if there is dirt inside, you need to open the back cover, remove the dirt inside, and then install it back in order.

2. Drainage pipe problems.

Drain pipe failure will also lead to water leakage, at this time it is necessary to purchase the same type of drain pipe to replace, so that the leakage problem can be effectively solved.

3. There are foreign bodies in the drain solenoid valve.

There is a drain valve at the bottom right of the equipment, which is easy to accumulate impurities after a long period of use, resulting in the drain valve being blocked or the drain pipe being bent and deformed.

4. The sealing ring is lost and the stove is elastic.

The loss of elasticity of the sealing ring, coupled with the long working and wear, led to a gap between the washing machine shaft and the oil seal, so the washing machine leaked and failed. To troubleshoot the problem, simply remove the wheel and shaft, pry off the damaged oil seal, and reinstall it.

5. The inside of the washing machine is aging.

The sealant gasket is worn and needs to be replaced, or the screws that fix the reducer are loosely rotated, resulting in the gasket being loose and needs to be tightened. Of course, there is also a more common water leakage fault, that is, the washing bucket has deteriorated. If the leak is on the top of the washing bucket, you can use adhesive to repair it.

If the leak is under the bucket and the crack is long, it is usually only necessary to replace the bucket with a new one.