How to set page numbers like page number 1 3 2 3 3 3 in word

The cover and table of contents of the document occupy two pages of the text, and pages 3 to 10 of the page number are numbered in Roman numerals, and after page 11, they are numbered from the first page with Arap numerals.

Word2010 operates in this order: insert the page number into the full text first, put the cursor at the end of the document on page 2, and click "Next" under the "Page Layout" Separator drop-down menu (remember to insert section breaks as shown in Figure 1). This inserts a section break between page 1 and the following page.

The purpose of inserting section breaks is to keep them from affecting each other).

Place the cursor at the end of page 10 of the document and click "Next" under the "Page Layout" drop-down menu (remember to insert section breaks, as shown in Figure 1). This inserts a section break between page 10 and the following page.

At this point, page 3 may not be numbered from the first page, but we actually want page 3 to start with "i". In this case, you need to select the page number on page 3 first, and uncheck the "Link to previous header" under the "Design" menu (as shown in Figure 2). Select and point to the page number right-click menu under "Format Page Number" Select "Start Page Number" and manually fill in "1" (according to your needs:

Select the Roman alphabet format. OK, that's it.

Then select the page number on page 11 and uncheck "Link to previous header" under the "Design" menu (as shown in Figure 2). Select and point to "Format Page Numbers" under the page number right-click menu Select "Start Page Number" and manually fill in "1" (according to your needs: select the number format of the Arapa.

OK, that's it.

Of course, you can now delete the page numbers on the page and rest assured that it won't affect the page numbers anymore, because they are already separated by section breaks.

The watchtower, the lord).

You can choose to insert the page number first, which will enter the header and footer state, and you enter a similar but fixed word such as -3 after the 1 that appears, and the page number will automatically change to a state like -3.

To set the header or footer, click "Insert Page Number" on the header and footer toolbar, then enter -after the page number, and then click "Insert Page Count" on the toolbar, and you're done.

This can be set in this way, usually with section numbers and page numbers.

Do you still say that you are the page number and the total page number.

1. Open the Word document and click the insert button at the top of the interface.

2. Click the page number button in the interface that opens.

3. Click on the bottom of the page in the drop-down menu that pops up and select the normal number 2.

4. Then enter "1-" in front of the inserted page number, and you can enter the effect of entering the 1-1 page number.

1. Directly on the third page of word, you can see that the page number is 3, and you need to click on the page number.

2. A new menu pops up in the next step, and you need to select the page number setting to jump.

3. If there is no problem at this time, follow the diagram to determine that the page number is set to 1 from the third page.

4. In this way, the relevant results will be found, and the purpose can be achieved.

The specific steps are as follows:

1. First of all, open the word document that needs to be operated as shown in the figure below, and then enter the next step.

2. Secondly, click on the insert - page number in the upper menu bar, as shown in the figure below, and then go to the next step.

3. Next, click on the inverted triangle below the page number, as shown in the image below, and proceed to the next step.

4. Then, select the page number insertion position, alignment, and font size as you need, as shown in the image below, and then proceed to the next step.

5. Finally, you can see that the segmented page number is set, as shown in the figure below. In this way, the problem is solved.

You can choose to insert the page number first, which will enter the header and footer state, and you enter a similar but fixed word such as -3 after the 1 that appears, and the page number will automatically change to a state like -3.

To set the header or footer, click "Insert Page Number" on the header and footer toolbar, then enter -after the page number, and then click "Insert Page Count" on the toolbar, and you're done.

This can be set in this way, usually with section numbers and page numbers.

Do you still say that you are the page number and the total page number.

Select the desired "style" as needed and set the relevant settings, and "OK".