Philips handheld steam ironing brush can t steam what can be done

Garment steamer does not produce gas.

1.Reason: Do not use the residual water in the pump for a long time to form scale or mucus, so that the chips in the pump are bonded. Method: Follow the water pump (the water in the water tank should be stored during storage.)

Pour it out) 2Cause: New product, the water tank is not in place or has not reached the specified water level. Method: Add water to the specified water level and return the water tank to the new place.

3.Cause: Lack of cleaning for a long time, clogged filter or clogged steam hole. When the filter screen is blocked, the host heats up.

But there is no sound of boiling water. If the steam hole is blocked, there is the sound of boiling water. Method: Regularly clean and maintain the machine.

4.Reason: The dust pad of the steam connection port of the host has not been unplugged, and the host has the sound of boiling water. Method: Remove the dust pad before connecting the steam pipe.

5.Reason: The water level in the tank is too low. Method: Add water to the water tank and call the specified water level.

6.Reason: The storage tank in the sink is not placed, the sink water cannot flow into the main engine, and the main engine is heated but there is no sound of boiling water. Method: Put the storage slot in the corresponding place.

7.Reason: The steam pipe is bent, and the host has the sound of boiling water. Method: Straighten the steam pipe.

8.The power control switch is not turned on - check whether the garment steamer is accurately connected to the power supply, if not, please turn on the power control switch.

9.The steam pipe is broken - ensure that the steam pipe of the garment steamer is well untied.

10.There is no water in the tank – turn off the garment steamer to refill the water.

11.The steam guidance light is not on - after the light is on, turn on the pump and grasp the button, and the pump mission light can be used after it is on.

12.The pump mission guidance light is not lit - press the pump grasp button on the handle, and the light is on steam.

13.The pedal guidance light is not lit - check whether the product is accurately connected to the power supply, turn on the pedal power and grasp the switch.

14.The handle mission guidance light is not on - press the steam head grasp button, and the light is on with steam.

I'm also using this one, there may be several reasons for not steaming: first, the garment steamer may not be fully heated, the landlord can let it heat up for about 45 seconds, and then use it after the temperature indicator is off; The second is that you may not have fully pressed the steam switch; The third is that the position you use may be wrong, you should put the garment steamer vertically and spray steam vertically; Fourth, there may be insufficient water in the fuselage, before continuing to iron, the landlord can remove the water tank, add some water and try again. If there are still problems, it is recommended to call the after-sales ** for help and find a Philips after-sales repair station to repair it

1. There is no water in the water tank: When the water level in your Philips steam ironing machine iron is lower than the minimum water level or there is no water in the water tank, the electric iron cannot produce steam. Please fill the water tank with water.

Make sure there is water in the tank or the water level is higher than the minimum (min) level. After that, your electric iron should be working properly again.

2. The iron is not ready for steam ironing: The Philips steam ironer needs up to 2 minutes to heat up before being ready to generate steam. Wait until the blue "Iron Ready" light stops flashing and stays on.

3. Failure to press the steam switch: The steam switch needs to be pressed to generate steam. If you have a Philips steam ironer with OptiTemp technology, always press the steam button to generate steam.

Note: If you own a Philips Steam Iron with a temperature knob, always make sure the temperature knob is in the 2, 3, or Linen position. When the temperature knob is at 1 o'clock or with the SYNTH setting or automatic descaling enabled, your Philips iron will not generate steam.

The above content refers to Encyclopedia - Garment Steamer.

The reason why the Philips garment steamer does not produce steam:

1. It may be that the power supply is not plugged in properly, or there is a problem such as poor contact at the power supply.

Solution: Plug the power of the garment steamer back in.

2. The garment steamer water tank is not in place or does not reach the specified water level.

Solution: Add water to the designated water level and return the tank to its new place.

3. If you use it for a long time and do not clean it, it will cause the filter screen of the garment steamer to be blocked or the steam hole to be blocked.

Solution: Clean and maintain the machine regularly to ensure that the filter screen and steam hole are unblocked.

4. The storage tank in the sink is not placed, resulting in the water in the sink cannot flow into the main engine, and the main engine is heated but there is no sound of boiling water.

Solution: Place the storage tank in place so that the water in the sink can flow smoothly into the main unit.

5. The steam duct of the garment steamer is bent, resulting in the steam being blocked.

Solution: Straighten the steam pipe of the garment steamer.

6. The garment steamer has been used for a long time, and there has been a fault inside.

Solution: Contact the after-sales personnel and let the professional personnel repair the processing, or directly replace a new garment steamer.

This answer applies to most Philips garment steamer models.

Hello dear <>

What should I do if the Philips steam iron can't be used for the first time 1. If you find that the water in the glass box is turbid or you find that there is white powder in the exhaust hole, you can use white vinegar and half of the water to inject it into the water tank, and then heat it for a few minutes for cleaning. After heating, pour out the vinegar for cleaning, which can be washed several times with clean water. 2. The steam iron will be used for too long, which will cause rust to grow in the pipe, resulting in the steam iron not being able to produce steam.

It is very likely that the heating part is broken, after all, it has been used for a long time, and if you want to continue to use it, you need to take it to a special repair department for repair. 3. There is hot gas in the steam pipeline, but the hot gas is very small, indicating that there is no problem with the heating parts. There is a small plastic piece at the bottom that can be unscrewed, unscrew it with a vice to slowly clean the dust inside.

Clean up and seal again.

Summary. Hello, glad for your question! After powering on, see if the iron indicator light is on, if it is, it should be fine. There are several cases in which steam is not ejected:

1. It is not placed in the steam gear. Press or lift the button with "steam" to indicate that it is in the state of steam dry ironing, and you must switch the position.

2. It's below the minimum water mark. Add water to the maximum scale.

3. The temperature is not enough. The steam injection area must be within the red scale area with high temperatures. If the knob pointer is not placed in this hot area (e.g. silk, wool, cotton, linen, etc.), no steam will be ejected.

4. Check whether the fumatore of the bottom plate is blocked. If the limescale is clogged, gently unclog it with a paper clip. That's why purified water is used.

Of course, it is okay to use boiled cool white water, but do not directly use tap water and well water with untreated water and alkali weight. Hope mine can help you!

Philips steam iron is not without steam what's going on.

Hello, very hungry to dig happy with your question! After powering on, see if the iron indicator light is on, if it is, it should be fine. There are several cases in which steam is not ejected:

1. It is not placed in the steam gear. Press or lift the "steam" rotten core button to indicate that it is in a steam dry ironing state, and you must switch the position. 2. It's below the minimum water mark.

Add water to the maximum scale. 3. The temperature is not enough. The steam injection area must be within the red scale area with high temperatures.

If the knob pointer is not placed in this hot area (e.g. silk, wool, cotton, linen, etc.), no steam will be ejected. 4. Check whether the fumatore of the bottom plate is blocked. If the limescale is clogged, gently unclog it with a paper clip.

That's why purified water is used. Of course, it is okay to use boiled cool white water, but do not directly use tap water and well water with untreated water and alkali weight. Hope mine can help you!

I've tried it all before, and I'm ready to take a look at it again.

If you recover from the above situation, don't you spray vapor even if you recover?

Summary. Hello dear. The Philips garment steamer does not produce steam methods, the steam duct is bent, and the host has the sound of boiling water.

Solution: Straighten the steam pipe. If the water remains in the pump for a long time, it will form scale or mucus, and the chips in the pump will be bonded.

Solution: Change the water pump (pour out the water in the tank when storing). For new products, the water tank is not in place or does not reach the specified water level.

Solution: Add water to the specified water level and put the tank back in place. Dear, <>

The above is the answer I summarized for you, I am very happy to serve you, please give me a thumbs up, thank you very much for <>

I hope mine is helpful to you, and then I hope you are happy every day and have a good life<>

Good luck always comes with you, oh <>

What should I do if the Philips garment steamer does not produce steam.

Hello dear. The Philips garment steamer does not produce steam methods, the steam duct is bent, and the host has the sound of boiling water. Workaround:

Straighten the steam duct. If the water remains in the pump for a long time, it will form scale or mucus, and the chips in the pump will be bonded. Workaround:

with a water pump (pour out the water in the tank when storing). For new products, the water tank is not in place or does not reach the specified water level. Workaround:

Add water to the specified water level and put the tank back in place. Dear, <>

In my hand, I summarized the answer for Bi Song, I am very happy to serve you, please give me a thumbs up, thank you very much for your <>

I hope mine is helpful to you, and then I hope you are happy every day and have a good life<>

Good luck always comes with you, oh <>

The outgassing is small. Poor contact. It may be that the power supply is not plugged in properly, hail or there is a problem such as poor contact at the power supply.

Solution: Plug the power supply of the garment steamer back into the water level if it can't reach the water level. The garment steamer water tank is not in place or does not reach the specified water level.

Solution: Add water to the designated stupid coarse water level, and return the water tank to the new location in the town.

1. The steam pipe is bent, and the host has the sound of boiling water. Method: Straighten the steam pipe.

2. If you do not use the water in the pump for a long time, the residual water in the pump will form scale or mucus, which will make the chip in the pump stick to the knot. Method: Follow the water pump (pour out the water in the water tank when storing).

3. For new products, the water tank is not put in place or does not reach the specified water level. Method: Add water to the specified water level and return the water tank to the new place.

4. The filter screen of the water tank is blocked, and the filter screen lacks scale in many sections. Method: Clean or replace the filter, and clean and maintain the main machine.

5. The dust pad of the steam connection port of the host has not been unplugged, and the host has the sound of boiling water. Method: Remove the dust pad before connecting the steam pipe.