How to install the set door, how to install the set door

The difference between the suit door and the traditional door 1, from the perspective of the overall material structure, there are the following differences: the "traditional" wooden door is made of pine or fir wood as the inner structure, and the outer layer is sealed with plywood (plywood) Plywood is a multi-layer board, a door leaf from the inner structure to the surface layer at least 8 glued surfaces, any glued surface problems will be reflected on the surface. Therefore, the unevenness and undulations on the surface of the "traditional" wooden door are the result of problems with the internal glued surface, while the set door is made of pine or fir solid wood as the inner structure, and the outer layer is sealed with Jixiang environmentally friendly MDF.

There are only four glued surfaces from the inner structure to the surface, which greatly reduces the possibility of unevenness in the surface. The traditional door is finished with plywood, and the solid wood lines are edged, and there will be a color difference between the edge strip and the veneer, and the edge strip will shrink and degum.

Steps to install the suit door

1. Adjust the position of the door sleeve and the grounding gap of the door, and the gap between the left and right sides of the door leaf is about 3 to 5 mm;

2. Put the door cover right, make the door cover on a plane, adjust the approximate position of the door cover, put the door leaf on it for comparison, observe whether the grounding gap of the door and the door gap on the left and right are suitable, and then observe whether the door leaf is on the same plane as the door cover;

3. After the door sleeve is adjusted, fix the door leaf with a special line card, and then fix it with the foaming agent Zheng Duanjia caulking;

4. Then the hanging door and lock can be installed.

Set door, also known as "shouting inspection whole door", "complete set of door", generally refers to the solid wood as the main material, the external pressure paste MDF as a balance layer, with domestic or imported natural wood veneer as the finish, after high temperature hot pressing, the exterior spray decoration of high-grade environmentally friendly wood paint composite door, in short, from the inside to the outside is required to be wood burning several materials.

The set door is the most popular and popular door product at present, so how to install the set door? Let me introduce you to the installation method of the set door!

1. The installation of paint-free indoor doors must be installed after the reserved opening, and it is strictly forbidden to install the masonry while installing or installing the masonry first.

2. The paint-free indoor door must be installed only after the ground engineering and coating operations are completed.

3. Install the door frame.

1) On the flat, smooth and clean ground, use a diameter electric drill to lead a 30-40mm deep hole at the upper end of the mullion, and use 4 60mm yuan nails to connect the horizontal frame with the two mullions firmly. The three frames are on the same plane; The horizontal frame is connected with the mullion at a 90-degree angle.

2) Fix 6-8 fixing pieces with wood screws on both sides of the mullion, "turn over" the assembled door frame on the ground, and fix the other 6-8 fixing pieces with wood screws. Nail "lock foot strips" and "lock corner strips" on one side of the mullion.

3) "Pre-fit" the door leaf and the door frame (with the opening side). The gap between the door leaf and the door frame is required to be uniform and reasonable.

4. The frame is connected and fixed with the wall.

1) Push the tightly assembled door frame into the door opening. Use a drop lance to check that the entire door frame is perpendicular to the plane.

2) to fix the piece'The hole is a point to determine the point of drilling on the wall.

3) Use an electric hammer with a diameter of 8-10mm to drill holes in the fixed hole points, nail into the wooden wedge in the drilling, and fix the door frame on the wall with yuan nails.

4) Inlay wooden strips in the gap between the fixed door frame and the wall, so that the door frame and the wall are firmly connected.

5. Install the door leaf.

1) Tick the slot, drill the lock hole, lock the plate base, and the deadbolt buckle. In the drilling operation, the decorative surface shall not be operated.

2) Comprehensive installation. The center of the upper and lower hinges is 300mm away from the upper and lower ends of the door leaf respectively. Before nailing the wood screws, first lead the nail holes, then drive the wood screws and tighten them.

The upper and lower hinges first screw a screw, then close the door to check whether the gap is appropriate, check whether the door frame mouth and the fan are on the same plane, whether the door leaf has fallen, and tighten the other screws after it is correct. It is strictly forbidden to "drive" the screws directly into the door frame.

3) Install the door lock. Lock position from the lower end of the door leaf 920mm; After the door lock is installed, pay attention to comprehensively check whether the door lock switch of the door leaf is flexible and whether the seam is appropriate.

The fastest way to install a kit door is in three steps: checking the opening, unpacking, assembling and positioning the door frame, gluing the door frame and installing the door sleeve line.

1. Check the hole and unpack the package

There are three categories of set doors, namely door frames, door sleeves and door leaves. Before installing the set door, you can check whether the size of the opening meets the installation requirements, and if it does not meet the requirements, immediately readjust it. Next, do the preparation work before installation, first unpack and check whether the door strip, sealing strip, door frame and other components are neat, which are the basis for the fastest installation method of the set door.

2. Assemble the door frame and locate the door frame

Before the door can be installed, it needs to be assembled and then secured. First, the door frame is clamped around the door frame with a wooden wedge, and then the tooling and the wooden wedge are supported on the door frame inside the door frame. By clamping the inner and outer wooden wedges of the door frame, the verticality, levelness and inner diameter size of the door frame can be better adjusted, and finally the design requirements can be met.

3. Glue the door frame and install the door sleeve line

After completing the previous preparations, it is time to officially install the set door. First of all, the watering can wets the wall, and after wetting the wall, then apply an appropriate amount of styrofoam. Slice the remaining styrofoam flat with a razor blade.

After four to six hours, the tooling and wedge can be removed, glued into the door frame grooves, and the door sleeve line can be fitted to the door frame so that they fit together perfectly. Finally, take stock of the scene, pack up the tools, and evacuate the scene.

Summary. 1. After the site is cleaned up to the site of the installation of the door, the door opening and the installation site can be cleaned first, the size of the door opening can be measured, and then the installation method of the door is planned, and then the size of the door leaf is measured, and the wall and ground can not be damaged and soiled during construction.

Pro, the detailed installation method of the set door:

1. After the site is cleaned up to the site of the installation of the door, the door hole and the installation site can be cleaned first, the size of the door hole can be measured, and then the installation method of the door is planned, and then the door ruler key is measured well, and the wall and ground can not be damaged and soiled during construction.

2. The detailed installation method of the door frame combination set door, the top plate of the door should be 20 to 50 mm longer than the actual door opening size, and the void rock of the door is roughly 6 to 8 mm, and two nails are nailed on one side, and the lead tease fixes the door frame. Then nail four pull tabs on the left and right sides of the door frame, put the door frame into the door hole, and nail two pull pieces in the middle of the top plate.

3. Install the door frame and put the door frame into the middle of the door opening, both sides must be even, use sawdust to disturb the gap between the door frame and the door hole on both sides of the four fixed points, the height of the floor to the door Jinqin fan is ten millimeters, and the vertical door frame is used off on the board of the installation hinge, and the door frame is fixed.

4. The detailed installation method of installing the door set door, install the hinge on the door leaf, the flatness of the door leaf and the door frame should be paid attention to by the special beam, the door leaf is installed on the fixed door frame, close the door, you can try whether the switch is free, and whether the top plate of the door of the world nuclear brother is just right to search.

5. Install the lines according to the size of the door frame and cut the reeds into 45 degrees, use the vertical lines and horizontal lines to glue the 502 glue pin into a 90-degree angle, and then nail the dust on the door frame and cover the nail strips.