How long is the warranty period of X Trail front brake pads?

Nissan Qijun brake pads can be used normally for more than 30,000 kilometers without a fixed replacement cycle. The original high-mounted brake pads are Hitachi brand, model D1060-3TA04.

Nissan Qijun brake pad replacement tutorial.

The brake pads can only be replaced after the cylinder is retracted. The front wheels can be removed directly with tools and do not require computer settings. Next, let's take the next round as an example.

Connect to the vehicle via a computer and select "Open Rear Brake Cylinder" on the brake pad replacement setting screen. After waiting five seconds, you can hear a sound indicating the cylinder separation, and then the parking brake motor retracts.

Note: The owner needs to open the brake fluid cap as the brake fluid will flow back when the driven cylinder is retracted. )

Then loosen the two nuts of the lid. If the sub-cylinder is not completely separated, it can be manually pried open with a flathead screwdriver.

At this point, remove the caliper cover and install a new action tab. The side with text labels is on the outside, and the side without text labels is facing inward.

After the installation is completed, select "Turn off the rear brake cylinder" on the setting interface of the trip computer, and the brake motor will reset after a few seconds.

Millions of car purchase subsidies.

X-Trail brake pads 3 50,000 kilometers need to be replaced. Automobile brake pads, also known as automobile brake pads, refer to the friction materials fixed on the brake drum or brake disc that rotates with the wheels, and the friction lining and friction lining bear external pressure to produce friction to achieve the purpose of vehicle deceleration. The steps to replace the brake pads are as follows:

1. Before replacing the brake pads, you should open the lid of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page, if the brake fluid page is above the highest limit, you should suck out some brake fluid to prevent the brake fluid from overflowing during the replacement process;

2. Prepare the brake pads to be replaced and remove the wheels where the brakes are located. In the process of dismantling, it is necessary to avoid scratches on the rim;

3. Remove the bolts of the brake caliper with a wrench combined with the sleeve, and then remove the brake disc (if there is a brake induction line, the brake induction line should be removed from the bench first). Observe whether the brake pads are overworn, or cracked, and replace them in the next step;

4. Since there will be a lot of sand or mud in the brake caliper, it should be cleaned with a rag, and then applied silencer paste to prevent abnormal noise when braking;

5. Use the piston pressure pump to press the piston to the position of the blind lion that cannot be pressed, then install the brake pads on the brake caliper, install the new brake pads in place (those with brake induction lines should also be installed), tighten the guide bolts, and the installation is completed;

6. After installation, cover the lid of the liquid storage tank, enter the car and press the brake pedal a few times, and reset the brake. Then observe the height of the brake fluid, which should be within the appropriate height range for grinding;

7. Test drive after changing to check whether the braking effect is reflected.

Millions of car purchase subsidies.

Nissan X-Trail brake pads can be replaced for 100,000 kilometers. The brake pad is the front of the wearing part, and the replacement cycle of the brake pad is determined according to the driving habits of the owner; The thickness of the vehicle brake pad is worn to the original 1 3 and needs to be replaced, if the brake pad is not more slippery in time, it will cause the vehicle brake to lose control, affecting the safety of driving.

Here's how to replace the brake pads:

1. Before replacing the brake pads, you should open the lid of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page, if the brake fluid page is above the highest limit, you should suck out some brake fluid to prevent the brake fluid from overflowing during the replacement process;

2. Prepare the brake pads to be replaced and remove the wheels where the brakes are located. In the process of dismantling, it is necessary to avoid scratches on the rim;

3. Use a wrench combined with the sleeve to remove the bolts of the brake caliper, and then remove the brake pad (if there is a brake induction line, the brake induction line should be removed first). Observe whether the brake pads are overworn, or cracked, and replace them in the next step;

4. Since there will be a lot of sand or mud in the brake caliper, it should be cleaned with a rag, and then applied silencer paste to prevent abnormal noise when braking;

5. Press the piston to the position where the piston pressure pump cannot be pressed, then install the brake pads on the brake caliper, install the new brake pads in place (those with brake induction lines should also be installed), tighten the guide bolts, and the installation is completed;

6. After installing Brother Qipei, cover the lid of the liquid storage tank, enter the car and press the brake pedal a few times, and reset the brake. Then observe the height of the brake fluid, which should be within the appropriate height range;

7. Test drive after changing to check whether the braking effect is reflected.

Millions of car purchase subsidies.

Nissan Qijun brake pads can generally be used for about 100,000 kilometers, and if they are good, they can even be used for 150,000 kilometers. The price of front and rear brake pads is about 1,000 yuan, and there is no clear replacement cycle for brake pads. The lifespan of brake pads largely depends on the driver's driving habits.

If the braking frequency is high and the braking time is long, the service life of the brake pads will be shortened. When it is found that the thickness of the brake pad is less than 1 3 of the new thickness, it should be replaced in time to avoid brake failure.

1.Vehicles that often drive on city roads use their brakes when they need to stop and drive, so friction pads inevitably wear out faster than vehicles that often drive on large highways.

2.For vehicles with heavy loads, brake pads are heavily worn. Due to the large mass and the increase of inertia, the braking force of the stop car also increases correspondingly, so the load on the friction plate will also be large, which will inevitably aggravate the wear. This is also the reason why it is difficult for large trucks to brake.

There is still a break-in period after replacing the brake pads with new ones. Please avoid emergency braking for the first 200 kilometers, because the brake pads have not reached the maximum friction coefficient at this time, and the brake pad friction may be noisy.

Millions of car purchase subsidies.

Nissan X-Trail automotive brake pads can generally be applied for more than 100,000 kilometers, and even more than 150,000 kilometers if it is good. The price of the front and rear brake pads is around 1000 yuan, the brake pads do not play a role in the replacement cycle time established, the service life is very large due to the driver's driving habits, the braking frequency is high, the braking time is long, and the service life of the brake pads is shortened. When it is found that the thickness of the brake pad is lower than the new wall thickness of 1 3, it should be replaced immediately to prevent brake failure.

1. Cars that are often driven safely in road traffic must use the brake pedal if they go slowly, so the friction pads will wear out faster than those that often drive on the road.

2. Cars with excessive load will have large wear and tear of brake pads. Because the mass is large, the inertia force will expand, and the braking force that slows down the vehicle will also be relatively increased, so the load borne by the friction plate will also be very large, and the damage will be aggravated. That's why large trucks can't stop when braking.

There is also a running-in time after replacing the new brake pads, please prevent emergency braking for the first 200 kilometers, because the brake pads are not the highest friction resistance at this time, and there may also be a sound of brake pad friction.