How does Zhijun semi manual stacker work?

When selecting and determining the configuration, it is necessary to describe the working conditions in detail to the stacker dealer and conduct on-site investigation to ensure that the purchased stacker fully meets the needs of the enterprise. Even after completing the analysis of the above steps, it is still possible that several models can meet the above requirements at the same time. At this time, you need to pay attention to the following aspects:

Different models, different work efficiency, then the number of forklifts and drivers required is also different, which will lead to a series of cost changes, see the discussion of cost in the performance evaluation section of this article.

If the stacker is operating in the warehouse, the width of the passage required by different models is different, and the lifting capacity is also different, which will bring about changes in the warehouse layout, such as changes in the storage capacity of goods.

Changes in the number of models and numbers will have an impact on many aspects such as fleet management.

Different models of different models of market ownership is different, its after-sales support capabilities are also different, for example: low-level driving three-way stacker and high-level driving three-way stacker both belong to the narrow channel forklift series, can be in a very narrow channel (meters) to complete stacking, stacking, pick-up. However, the former cab can not be lifted, so the operating vision is poor, and the work efficiency is low.

Because the latter can fully cover the functions of the former, and the performance is more outstanding, the sales of the latter in the market in Europe are 4 5 times higher than the former, and in China it is more than 6 times. Therefore, most of the leading companies focus on the development of high-level driving three-way stackers, and low-level driving three-way stacking forklifts are only used in small tonnage and low lifting height (generally within 6 meters). When the market sales volume is very small, the number of engineers in after-sales service, engineer experience, parts inventory level and other service capabilities will be relatively weak.

It is necessary to comprehensively evaluate the impact of the above aspects and choose the most reasonable plan.

The hand-cranked stacker is called a manual hydraulic stacker, which is composed of three parts: hydraulic system, mast and fork.

The car uses manual hydraulic jacks (i.e. hydraulic devices) as the power to lift heavy objects, and manual push and pull to carry heavy objects. The hydraulic device is equipped with an oil return valve, which controls the fork descending speed through the handle, and makes the hydraulic system act correctly, safely and reliably.

The structure and operation of the manual semi-electric stacker are very simple, and its function is equivalent to installing an electric lifting part on the manual hydraulic stacker, in addition to thisThe structure and working principle of the hydraulic stacker are the same.

In some of the more frequent work of the site will be very practical, compared to the manual lifting of the product is more labor-saving, time is also saved, maintenance is also very simple, open the back cover to see whether the battery distilled water is at a certain water level, that is to say, at least the battery inside the storage sheet soaked.

Charging and discharging have a direct impact on the life of the batteryWhen each semi-electric stacker is produced, there is a design ammeter to prompt the power situation, charging and discharging can be prompted according to the ammeter green, yellow, red, usually the machine battery can last 4-5 hours when working at full load, and the ammeter pointer points to the yellow marked position when indicating that it is about to be charged, note; It is recommended not to wait for the pointer to point to the red mark for charging, as this can easily damage the battery.

Stacking truck load curve, any kind of stacking equipment has load curve requirements, please operate in strict accordance with the instructions, the load curve means that the object will produce different weight pressure after leaving the ground, many users think that they bought a load of 1 ton, raise 3 meters of stacking truck, you can lift a ton of goods to 3 meters high, this is a misunderstanding, usually the load curve has a basic standard.

MAXBO Mook Principle: Electro-hydraulics.

The selection of high-quality pumping stations, lightweight, flexible, labor-saving and efficient;

Ergonomic handle, with plexiglass partition, wide field of vision, safe;

Lightweight, easy to operate, reliable, and economical for small materials.

The principle of electrohydraulics.

Linggong forklifts.