What should I do if the water pipe in the lower filter fish tank is loud

In fact, it's very simple, just a towel to solve the problem, cut the water inlet with a towel two inches long wrap, let the water into contact with the water in the fish tank, cut two long points with a towel, and put two yogurt straws on the sewer pipe, it solves the problem, if there is a sound is the sound of the submersible pump.

There are two main reasons why the sewer pipes in the home need to be wrapped, one is to be soundproof, and the other is to make it look more beautiful. Here are a few ways to wrap the sewer pipe.

First of all, there are two less common ones, the first is to make a frame of a wooden keel next to the water pipe, and then install a gusset of PVC on its surface. The other is to nail a layer of wood on the surface of the keel frame, and then add aluminum-plastic panels. However, in this case, the wooden keel is more likely to deform due to moisture.

Nowadays, it is common to use soundproof cotton to wrap the sewer pipe, then put a keel on its surface, and finally add tiles. Because the sound insulation effect of tiles is not obvious, it is necessary to use sound insulation cotton. This method does not take up space, but it will be relatively high.

Another way is to build a wall, the sound insulation effect of this method is still very good, and there is no need to pack sound insulation cotton, ** cheap, but the space occupied is relatively large.

This is the effect of the bathroom

It depends on which part of the sound is mainly produced, and if it is the noise emitted by the motor, it can be absorbed by lining an elastic substance such as a sponge under the motor; If it is the sound of the water flowing on the surface of the water, you can use cotton thread or cloth strips to drain the water from the outlet, so that the water can seep into the water body through the drainage, so that there will be no falling sound.

Especially when the density of fish farming is relatively large, the filter has the function of increasing oxygen, which cannot be turned off casually, otherwise it is easy to cause the adverse consequences of poor water quality.

Extending the sewer pipe under the surface of the fish tank reduces noise.

Raising the water level and reducing the drop in the water can also reduce noise.

At the launching site, add a sponge cushion to reduce noise.

The sewer pipe of the bottom filter mainly transports the water overflowing from the fish tank to the filter cotton. Regardless of whether there is dry and wet separation, whether it is connected to the rain pipe or not. But be sure to do a U-shaped silencing structure and a ball valve.

These two points can help to eliminate the sound of water running in the overflow area.

What to do if the fish tank pump is loud, the effect of the simple method is immediate.

It is better to insert a thinner sewer pipe into the thick pipe or reduce the diameter of the sewer pipe, and it is better to replace the thin sewer pipe. This is because if the water level is higher before the upper filtration, the air will be removed, and if there is no air, there will be no noise in the water.

The thickness of the water pipe will also determine whether the sound is loud or not, if the pipe is thicker, you can try to change to a thinner pipe. The thicker the pipe, the louder the current, the louder the sound. If there is a problem with the location of the water inlet, you can try to put something in the place of the water inlet so that the air will not be sucked in, which can also greatly reduce the noise.

Reduce the impact height or slow down the flow of water.

Reducing the impact height lengthens the sewer pipe and extends it below the surface of the water, reducing the sound of the water hitting the water surface.

To slow down the flow of water, add a spiral silencer to the sewer pipe, which can reduce the sound of the water hitting the pipe.

The filter power is too great, my cylinder is bigger than yours, it is jebo1260, the power is 18--20w, and the head is meters.

1. If the water from the sewer pipe hits the water surface of the bottom tank, the sewer pipe can be lengthened so that the sewer pipe is below the water surface of the bottom tank.

2. If it is due to the overflow tank air sucking into the sewer pipe, you can install a valve in the sewer pipe, and by adjusting the flow rate, the liquid level in the overflow tank will have a certain height, and the air will not be sucked into the sewer pipe, and the sound will be smaller.

3. If it is due to the impact of falling water in the main cylinder on the water surface in the overflow tank, you can raise the water surface in the overflow tank of Xunlu Gao, or add a piece of filter cotton mu head belt and something like that at a certain height in the overflow tank to buffer the falling water.

4. If the sound is loud due to the motor, you can absorb the vibration sound by adding an elastic substance such as a padding sponge under the motor.