What is the difference between formatting a disk partition with the NTFS file system and using FAT w

As mentioned upstairs, the only drawback of NTFS compared to FAT is that it does not support DOS access.

If you don't use DOS often, it is extremely stubborn and irrational to use FAT as well.

The specific steps to convert the EFI system partition format to FAT32 are as follows:

1. First, find the Run option in your computer's start menu and click on it:

2. Enter the cmd command and press Enter:

3. Then a command prompt window will pop up:

4. Enter the conversion command in the command box that appears:

5. Finally, after the command execution is completed, the conversion of the drive letter has been completed

1. Format the C drive when reinstalling the system.

1. Optical drive starts.

1) Award Bion settings.

Reboot, press del to enter the BIOS Award interface, use the arrow keys in the function key area to select the second line "BIOS Features Setup", press enter to enter the BIOS Features Setup interface, find the seventh line "Boot Sequence", and use PGUP or PGDN to turn the page to replace the A,C displayed on the right of it with CDROM,C,A. Press esc, press f10, and hit y to save and exit.

or Award BIOS settings.

Reboot, press Del to enter the BIOS Settings interface, find Advanced BIOS Features (Advanced BIOS Parameter Settings), press Enter to enter the Advanced BIOS Features interface, use the keyboard D-pad to select the First Boot Device, use PGUP or PGDN to turn the page to change the HDD-O on the right to CDROM (CD-ROM boot), press ESC, press F10, and then hit Y to save and exit.

2) Insert the XP installation disc into the optical drive, reboot it, and see the CD ...... appear at the bottom of the screenWhen the word is written, press any key in time, otherwise the computer will skip the light and start from the hard disk again. After the XP system disk is opened, it is necessary to start installing the program, copy the file, load the hardware driver and enter the Chinese interface of the installation wizard.

2. In the pre-installation.

1) After scanning, welcome the installer, select install - enter;

2) Check the startup environment - enter;

3) Agreement, agree, press f8;

4) Specify which partition to install, c--enter;

5) Specify the use of the file system, format the disk partition with FAT32 (or NTFS) (fast) --Enter; In this way, the C drive is formatted.

2. If you only install XP, it is better to use NTFS, so that FAT32 can also be used; If you install 98 or install XP, 98 dual system will make FAT32.

You have the system installation disk on the partition when formatting. It is good to choose NTFS.

Choose NFTs as the system disk. fat32 put the file.

What is the format of other disks, what grid is used for C disks.

The difference between FAT32 and NTFS:

FAT32 and NTFS are two partition formats of hard disks, according to the data tested by authoritative institutions, FAT32 will be 5% faster than NTFS, but NTFS has the following advantages: 1).Files larger than 4GB can be accessed.

2).Better diagnose and correct hard drive errors. 3).

It can manage single-partition hard drives larger than 40GB, and NTFS uses a smaller cluster size, so it can save hard drive space to a certain extent. Note: By default, Windows98 ME cannot access the NTFS partition format, Linux can read the NTFS partition, but cannot write it.

1. Select the hard disk partition that needs to be formatted (note that important data files should be backed up before formatting, if it is a system partition such as C partition formatting, you can have a disc or U disk to enter the PE maintenance system after starting the computer, and the operation method is the same).

2. Right-click on the selected partition and click "Format" in the options menu that appears.

3. Select "NTFS" in the "File System" option in the format window that appears, then click "Start" and wait for the formatting to complete.

At the command prompt, enter: convert x: fs:

NTFS (where X is the drive letter) and then press Enter, and the rest of the operations are performed as prompted. However, NTFS converted by command is still slightly different from NTFS directly formatted, and it does not give full play to the advantages of NTFS, and only supports a single large file above 4G.

Click on the "Start Program Attachment Command Prompt" (this is a built-in DOS-like interface in Windows XP, and all the internal instructions are basically the same as those under DOS).

If you want to convert the C drive to NTFS, enter "Convert C: FS:NTFS" under Start -- All Programs -- Accessories -- Command Indicator.

If you want to convert drive D to NTFS, enter "convert d: fs:ntfs" under Start -- All Programs -- Attachments -- Command Indicator.

If you want to convert the E drive to NTFS, then enter "Convert E: FS:NTFS" under Start - All Programs - Accessories - Command Indicator.

Analogy.

When formatting, just select NTFS directly.

1. When the computer is reinstalled, choose how to format the system disk into the format you want 2. Use third-party software, such as pq, pm

3. To convert the volume to NTFS from the Command Prompt, open the Command Prompt window, and type: Convert Drive Letter: FS:NTFS