How to memorize the points in subject 2? Subject 2: All point formulas

Subject 2. The main thing is to watch, which requires you to fix your seat and "adjust" your eyes.

When you open both eyes at the same time, it is difficult to align near objects with distant objects, so you need to close one eye to make sure that it is accurate. Personally, I have a habit of closing my left eye and opening my right eye, in fact, I can do it. Don't change it after choosing one eye, especially if you can't practice with your left eye and look with your right eye during the test.

Inverted piles. Get on the bus: Adjust the seat first, then the rearview mirror. The body accounts for one-quarter of the rearview mirror, and the rear door handle tops the upper edge of the rearview mirror.

Electronic road test (close your left eye and open your right eye): get on the bus and adjust the seat to shake down the glass, and then adjust the rearview mirror. In the right rearview mirror, the rear door handle is fixed in the upper left corner. The rear tires can be seen in the left mirror. Wear a seatbelt.

Very important! Turn on the left direction light.

1.Side parking.

If you can't see the corner in the right rearview mirror (it's a bright mark during the test), you will be killed in the right direction. Looking in the left rearview mirror, the rear of the car is back in the right direction when it is a fist away from the corner. Killed in the left direction when the wheel was pressed into the line. When the body returns to the center to a little crooked, step on the brakes and stop, and do not turn back to the direction.

2.Ramp parking: Turn to the left wiper along the top white line.

Uphill until the right front and rear mirrors are parallel to the right lever, the brakes are pressed, and the clutch does not move.

3.Ramp start: Lift the clutch slightly when you release the brakes until you are about to loosen.

4.Right-angle turns.

The shunting position is until the person is in the middle of the left and right iron bars. Walk slowly until the corner of the iron bar reaches the black frame, then kill to the left.

Curve: When the left corner covers the right curve, make a circle to the left, and the direction is based on the corner covering the curve. When the left corner crosses the left curve, the direction returns to the right. When the right corner is about 10 cm away from the left curve, make a circle to the right and fine-tune until you get out.

When taking the driver's license test, subject 2 is a field test, and if you want to pass subject 2, it is very important to learn to find something to watch. Today, I will help you sort out the important points, lines, and references of subject 2. Remember these, and the second section will be stable

1. There are 5 points of the engine head cover.

1. The left vertex of the head cover;

2, 1 3 places on the left side of the head cover;

3. the midpoint of the head cover;

4, 1 3 places on the right side of the head cover;

5. The right vertex of the headcover.

Remembering these 5 points of the hood can help you easily determine the accurate distance between the car body and the curb. When parking on a ramp, when the side line coincides with the left or right side of the hood 1 3, it means that the left or right side of the car body is exactly 30 cm away from the side line.

After entering the corner, when the vertex on the left side of the hood is aligned with the yellow line on the right, you should immediately make a circle to the left to turn in the direction, and when the vertex on the right side of the hood is aligned with the yellow line on the left, you should immediately make a circle to the right and reverse.

Second, the lower edge of the rearview mirror.

The lower edge of the rearview mirror is mainly used to find the parking position. For example, in the process of reversing backwards, when the yellow line in front of the garage coincides with the lower edge of the rearview mirror, you can step on the brakes to stop, otherwise you will press the line if you reverse backwards.

3. Shoulders of the trainees.

In fact, the shoulders of the students are also an important reference for finding points. In a right-angle turn, if it is a right-angle to the right, when the student's shoulder is aligned with the right corner line, the right direction is immediately killed.

Fourth, the left and right rear wheels.

The rear wheels on the left and right sides of the car let you know if the storage position is appropriate when reversing into storage. Take the right inverted warehouse as an example, when the distance between the right rear wheel and the storage angle is 30 cm from the right rearview mirror, the storage position is moderate. When the distance is too far, it means that the left wheel has the risk of crimping; When the distance is too close, it means that the right wheel has a risk of crimping, and both situations should be corrected in time.

Pay attention to the control of the vehicle's speed. Mainly by stepping on the clutch level, if necessary, you can step on the brakes slightly, but do not step on the stop, "slow speed, fast direction" is the main point.

Remember not to stop and do not stick your head or arms out of the window. Except for the section between the test areas of each project, you can stop and wait, once you enter the test area, you cannot stop in the middle of the operation.

The steering wheel is good to play, the clutch is also easy to press, control the speed, drive slowly, play less and return quickly, and pay attention to the details.

Subject 2 students have just started and memorized each point, which is half the success.

Subject 2: All point formulas are as follows:

1. Reversing into storage: lead the car into the field over the shoulder line, and observe the left mirror slowly falling; As soon as the point arrives, it will be killed, and the thirty distance will be adjusted; The deviation is adjusted in advance, which width is in which direction to turn; If the body garage line is parallel, quickly return to the steering wheel; Pay attention to the line under the left mirror, and step on the brake as soon as the position is reached; Out of the warehouse optimistic about the rear wheel, tens of millions of crushing the corner line of the library; The left side of the library is very similar, and you will be proficient after practicing a few more times.

2. Side parking: drive into the area to collar the line, 30 cm to adjust; Observe the right mirror slowly falling, and then hit the right side when it is your turn; Pay attention to the left side mirror, the inner corner appears to be back to normal; The left mirror observes the left rear wheel, and the dashed line is killed if it is pressed quickly; If the body garage line is parallel, immediately press the brake to stop; Remember to turn when leaving the warehouse, and slowly lift the clutch line.

3. Curve driving: Curve driving is very simple, and the car is correct before entering; First put the line on the right side, and hit the left when you reach the point; Remember to be slow and hit the right side of the point; Pay attention to observe at all times, and take care of both the left and right; Out of the warehouse look at the rear wheel, don't put that line tail pressure.

4. Right-angle turn: right-angle turn to the right, 30 cm to adjust; Drive into the test area at low speed and turn on the turn signal in advance; As soon as the point arrives, it will be killed, and the clutch speed will be stable; If the line around the car is parallel, immediately return to the steering wheel; Drive safely out of the right angle and into the test area of the lower round.

5. Half-slope start: drive into the area to the right, 30 cm to adjust; In addition to adding some oil when going uphill, the power is enough to put the slope uphill; Then slow down a little and leave some time to look at the point; Observe the left mirror point, and press the clutch brake together; The handbrake can not be forgotten to pull up, and the clutch is slowly lifted to find linkage; The body shakes violently, and finally loosens the handbrake; A smooth start is completed, and the clutch should be loosened downhill.

The rules of the driver's license subject 2 test are as follows:

1. There are two chances to pass the exam, and each opportunity needs to pass five items. If one project fails, all five projects must be re-enrolled.

2. If you fail the first chance exam, then the second exam will be taken. The process of the test is the same as the first test, the same car, the same test lane. Fingerprints must be re-verified.

3. After the test, candidates must leave quickly. They must not interfere with or instruct others to take the test. They should leave the test room through the exit and bring the sign-in number to the score printing window to print the score report.

If you can't find the right point, you can try the following methods:

1. Find a good reference.

Whether the car is straight or not, you can find a reference and compare it. This can be a marking, a wall parallel to the body, a tree, etc.

2. Look into the distance.

If you keep staring at the small area of the body attached to Zheng Jin, you can only find the problem when there is a lot of deviation. When a novice is driving, he should look into the distance, so that it is easier to find out whether the car is driving straight, and if there is a deviation, it is good to correct it in time.

3. Know how to make appropriate corrections when playing the steering wheel.

Don't drastically modify the steering wheel just because the vehicle is out of direction. Proper correction of the steering wheel still requires more practice in practice.

4. Practice more.

In addition, when you usually practice driving, practice more, think more, and be flexible. Usually practice to find a feeling, so that it is not easy to panic and not easy to get nervous during the exam, and it is basically over. Because many people either can't take the exam, or they are nervous.

Pass the subject two tips

2. When parking in the side direction, if the rearview mirror cannot see the rear wheels, you can stick your head out or tilt your head to look at the rearview mirror.

3. If you don't grasp the fixed point of the ramp, don't press the line in order to pursue a perfect score. When starting on the ramp, you must stabilize the clutch, control the balance of the throttle and the clutch, avoid turning off the engine and slipping, and seriously feel the shaking of the body.

4. Before entering the right-angle corner, you can slow down or stop, turn the wheel back or put the body right, and try to get close to the right sideline.

5. Don't be too anxious in the general direction of curve driving, and try to walk in a big circle after entering the curve.

6. Use 1 gear and reverse gear idle speed throughout the whole process of reversing and warehousing, look at your own points, control the key points and time, and know how to fine-tune the return position when you find deviations through the rearview mirror.

7. Mentality is also a very important point, and you should take the exam with a normal heart.

There are many points in subject two, and the points taught by each coach may also be different.

If you write down these points, will you be able to pass the subject 2 exam with trembling? Not necessarily, it takes luck.

What if the situation in the test room is different from the training field, and what if the sign marking a certain point does not exist?

People are nervous during the exam, and if they find that the situation is different from what they expected, they will increase their tension and cause their movements to be deformed.

Moreover, by rote memorization of these points and following the so-called correct process, you are just coping with the test, not learning to drive.

We should think about how these points came to be and why we did them at that point.

In addition to practicing in the car, you should also look down more, see the trajectory of the car, draw it on paper, and think about it in your head.

In this way, observe and think more, fully comprehend the meaning of each point, and know why it is scattered.

As the understanding becomes clearer, the feeling of the steering wheel is practiced, and you know how to play the direction in what situations.

Slowly practice muscle memory, and your hands will automatically do the action, without thinking about it for a long time.

If you practice to this level, you will be sure that even if the venue is slightly different during the exam, you will be able to adapt accordingly.

Moreover, with such a feeling, it can be regarded as learning to drive.

The method of looking at the points in Section 2 is as follows:

1. Adjust the direction and see that the edge of the left rearview mirror is driving along the inside of the Mino-celery line on the left side of the road, and the body is parallel to the solid line of the road.

2. When the front of the car presses over the right starting control line, and the left rearview mirror exceeds the control line, stop and hang up the reverse gear.

3. When driving in reverse, when the lower edge of the left rearview mirror coincides with the control line, hit the direction to the right.

4. Look at the right rearview mirror, when the distance between the right front corner of the garage and the wheel is about 30cm, return to the right direction.

5. After the wheel enters the garage, hit the direction to the right again, and when the body is about to be parallel to the edge of the garage, return to the right direction.

6. Observe the left and right rearview mirrors, fine-tune the direction, the distance between the two sides is similar, and the body is parallel to the garage sideline.

7. Look at the lower edge of the left rearview mirror, and when it coincides with the front edge line of the garage, stop and hang 1st gear.

8. Go out of the warehouse, when the edge of the front cover of the front cover covers the solid line of the road in front, hit the direction to the left.

9. When the front of the car presses over the left control line, and the left rearview mirror exceeds the control line, do not return to the right direction, stop, hang up the reverse gear.

10. Reversing driving, if the car is in good condition, you can directly complete the left storage, if there is a problem with the direction of the car, when the distance between the wheel and the left front corner of the garage is too close, return to the right direction.

11. When the wheel enters the library, it will kill the direction to the left again, and when the body is about to be parallel to the edge of the library, return to the positive direction.

12. Observe the left and right rearview yard spine mirrors, fine-tune the direction, the distance between the two sides is similar, and the body is parallel to the garage sideline.

13. Look at the lower edge of the left rearview mirror, and when it coincides with the front edge line of the garage, stop and hang 1st gear.

14. Go forward and out of the warehouse, when the edge of the front cover of the front cover covers the solid line of the road in front, hit the direction to the right.

15. Drive out of the reversing and warehousing test area.

The shorthand method of subject 2 is as follows: letter shooting;

1. There are five points on the front cover: the left vertex position of the front cover, the left third of the front cover, the middle position of the head cover, the right third position of the head cover, and the right vertex position of the head cover. These five points allow us to easily determine the distance between the car and the side of the road, especially when parking on a ramp, and these points allow us to park exactly 30 centimeters from the sideline.

2. The lower edge of the rearview mirror, find the parking position through the lower edge of the rearview mirror, such as when reversing into the garage, when the yellow line in front of the garage coincides with the lower edge of the rearview mirror, it means that it has entered the warehouse, and if the rear of the reversing car is the line.

3. The driver's shoulder, because the height and sitting habits of each person are different, so the position of the point is also different, at this time we can find the point through the shoulder, such as when turning at a right angle to the right, when our shoulder is aligned with the right corner, it is necessary to kill the direction to the right.

4. The left and right rear wheels, the rear wheels on both sides can let you know whether the storage position is accurate when reversing into the warehouse, taking the right wheel as an example, when the distance between the right wheel and the garage angle is 30 cm, the storage position is moderate, if the distance is too far, the left wheel may be pressed, and if the distance is too close, the right side may be pressed.

The point of subject 2 is determined as follows:

One. Fixed-point parking and starting

1. Examination standards: When parking, the body is more than 30 cm away from the sideline, the front bumper is more than 50 cm away from the pile line, and the rear slip is more than 50 cm when starting.

2. Sideline distance from the finger hole: check the distance between the body and the sideline through the reflector, generally speaking, the distance in the reflector is within 1 cm (recommended) through the wiper or the point on the hood as a reference, and the reference object on the slope of the project in the examination room, such as: the length of the dotted line, the cracks on the slope, tire marks, etc.

3. Fixed-point parking: reference objects in the examination room, such as: trees, sign poles, telephone poles, cracks, etc. on both sides of the parking position (recommended) The position of the lower right corner of the front windshield and the pile pole as a reference (affected by the distance between the body and the sideline) The lower edge of the left reflector and the pile line as a reference.

Second, right-angle turns

the relative position of the front door handle and the inside right angle; The relative distance between the hood and the front line of the car is generally about 1 second after the hood passes the front line.

3. Curve driving

1. Take the hood and the edge of the curve as a reference, the curve can be pressed on the outermost side of the hood you can see, or it can be a third of the part, or it can be half of the position, look at the right hood for a left turn, and look at the left hood for a right turn (recommended).

2. The extension of the reflector is also to look at the right side mirror when turning left, and looking at the left side mirror when turning right; In some test rooms, you are allowed to stick your head out of the window in subject 2, and you can put your head out of the window and control the direction with the left sideline as a reference.

4. Side parking

1. Storage: According to the relative position of the right rear door handle and the first right angle of the garage for the timing of the first direction, it can also be the dotted line on the side of the garage, and the left mirror sees the inner corner of the right rear of the garage, and the direction is corrected with reference to the inner corner of the right rear of the garage. The left mirror sees the left rear wheel and the garage outside line at the right time (fast or pressed to the line) to the left in the direction of the kill (third direction).

Fifth, reversing into storage

1. At the beginning of reversing, take the relative position of the lower edge of the reflector and the edge of the test area as a reference, and during the reversing, take the distance between the body and the corner of the garage seen in the reflector as a reference, and always maintain a distance of one grid (a dotted line) between the body and the corner of the garage, and the direction is corrected (recommended) if it is greater or less than this distance.

2. When parking, the relative position of the lower edge of the reflector and the side line of the garage is taken as a reference, and the body and the garage dotted line seen in the reflector can be used as a reference during reversing, for example: the body is always on the first dotted line, and the direction is corrected if it deviates.