What is Plan X for Polar Routing?

The X plan is divided into three parts, 1. Upgrade the **200w user open experience blockchain project; 2. Released the world's first blockchain routing: Pole X; Integrate more AI-level processors to become the AI hive of the future.

How to connect the router hardware and set up the network:

1.The router is connected to the network.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

6.The configuration is complete and you can enjoy the network.

The key to your problem is the IP conflict between the telecom cat and the Mercury router, which can be solved step by step like this:

Unplug the network cable connecting the modem to the WAN port of the router.

Enter admin, admin in the browser address bar, and admin to enter the route settings.

Exit the Setup Wizard, click Network Parameters -LAN Settings on the left, change the LAN port IP to, save and restart the router.

Enter admin, admin, admin, and re-enter the routing settings in the browser address bar.

In the setup wizard, select PPPoE Internet access mode and enter the broadband account secret. Note: Please do not enter the account password incorrectly, please carefully check whether the broadband user name and password entered are correct, pay attention to distinguish between Chinese and English input, the upper and lower case of letters, and whether the suffix is fully entered.

Follow the prompts to complete the wireless password setting and other operations, the wireless SSID can be changed or not, and finally click "Finish".

Plug in the cat network cable at the WAN port.

After the restart is completed, enter the management interface (, open the running state, wait for 1-2 minutes, the IP address of the WAN port status is the specific number instead of the line. If both are 0, check whether there are any errors in the WAN port settings and select it"Network Parameters—MAC address cloning", click"Clone the MAC address", then save and restart the router as prompted to see if there is any data left.

Note: After using the router, the computer can go directly to the Internet, and there is no need for broadband connection dial-up.

Broadband cats don't have to move; Connect a network cable to the WAN port of the wireless router on the LAN port of the modem; Then go to the router settings; Follow the instructions and select ppp0e as the dialing method

You connect the broadband cat to the network cable of your computer to the WAN port of your router, and then the computer connects the network cable to the LAN port of the router, and when it is finished, enter the username and password on your router in the IE address bar and set it up, just write the username and password of your dial number into it, and then select open in the wireless function block, and broadcast it. Look at the detailed instructions of your router.

Yes, routers are hardware in a local area network!

A router, also known as a gateway, is used to connect multiple logically separated networks, and the so-called logical network represents a single network or a subnet. When data is transferred from one subnet to another, it can be done through the router's routing function. Therefore, the router has the function of judging the network address and selecting the IP path, it can establish a flexible connection in the multi-network interconnection environment, can connect various subnets with completely different data packets and media access methods, the router only accepts the information of the origin server or other routers, and belongs to a kind of interconnection device at the network layer.

Yes, even the use of routers in the home also constitutes a local area network.

The most typical feature of network resources is sharing, and the function of the router is mainly routing, and it does not have the function of storing in shared resources, so it should be regarded as a hardware resource.

The function of the router is mainly routing**, and it does not store the function of shared resources, so it should be considered a hardware resource.

A hardware failure is basically a failure of the system to turn on, or an interface that does not work.

What routing to implement, VLAN and other commands and other functions are software problems, software problems are relatively easy to solve, you can reinstall an OS yourself.

First look at the light to see if it is on, and then you can find the same good device and copy the configuration to see if it is normal.

a. Install the wireless network card on the computer;

b. Generally, the wireless function of the new router is turned off, so it is impossible to use wireless router settings, to set up the router, you must use a network cable to connect the computer and the router before you can set the router. Here's how to set it up:

1. Connection: The LAN port of the router is connected to the computer with a network cable, and the WAN port is not wired first, log in to the router (for TP-Link routers: turn on your computer, click on the IE browser, and enter in the address bar: After pressing enter, the login page will pop up.

A. For the old router, enter the user name "admin" and password "admin", b. When the new TP-Link router is first set the router administrator password, in fact, this is to set a login password for the router, and in the future, anyone who wants to log in to the router is to enter the password to log in to the router.

c. For other routers, please refer to the router user manual;

2. Click on the network settings on the left, select PPPoe in the WAN port settings, enter the username and password given by the operator (if you don't know, call broadband customer service), and enter the DNS address (you can check your local DNS address on the Internet);

Note: If the router prompts that the network cable is not plugged in at this time, you don't need to pay attention to it at all!

3. Turn on the DHCP server;

4. For the wireless router, turn on the wireless network, turn on the wireless network function, and set the wireless login password (security option wpa-psk wpa2-psk, enter the key);

Save the parameters and it's OK,At this time, restart the router after connecting the network cable to the WAN port of the router,Wired is already available,Then open the wireless network card in the right corner of the desktop and right-click to view the available wireless network,Now your router broadcasts the signal,Double-click to connect,Enter the key to get it。 Wired and wireless access is available.

Configure the IP on the computer to automatically obtain, and in the future, you can go to the Internet by opening the browser directly on the desktop, and finally connect the computer to the network (wired, can be) to check whether you can access the Internet normally.

If you can't access the Internet, you can only connect to the computer that can access the Internet normally after dialing up the connection on the router, log in to the router again, and clone the MAC address in the WAN port settings.

Do you have a computer?

Does the router have wireless function? Is there a tie cable? Do you want to share the Internet with your phone, laptop, or desktop computer?

It's very simple,Offline access to the cat--- cat under the router--- router has wireless to turn on wifi, no wifi to use a network cable, IP address as long as a network segment with the router is good.

Then your computer must have two network cable interfaces, one connected to the network cable and one connected to the router.

Win7 desktop does not have a broadband connection at all, you click on the small computer at the bottom right, right-click to open the network and sharing center, after opening, at the top left, change the adapter settings, there is a broadband connection inside, pull him to the desktop, if there is no inside, create a new one.

Search: Win7 connected to the Internet in Windows did not detect any network hardware.

The router I use.

Forming a computer network requires a system. a.Router BCommunication Subnet CNetwork Hardware DNetwork software.

The answer is: DNetwork software.

Building a computer network requires network hardware devices and network operating systems.

Correct Answer:

a.Router BCommunication Subnet CNetwork Hardware DNetwork software.

a.Router CNetwork Hardware DNetwork software.