What is the reason why the soymilk machine only beats the pulp, but does not heat it?

There is an electronic component in the bean paddle machine called a relay, which is equivalent to an electronic switch. When the relay does not operate, the bean paddle machine will not heat up.

The reasons why the relay does not operate are:

1.There is no voltage at the relay coil end (the power supply line is broken, the circuit wiring is wrong or there is a short circuit);

2.insufficient voltage at the coil end;

3.coil breakage;

4.The relay was subjected to a strong shock.

In addition, it may also be that water enters the head of the soymilk machine during the cleaning process, and moisture enters the head for a long time during the heating process, causing problems with the computer chip. It is recommended to find after-sales service to repair.

There are two types of situations:

One is the situation that the new machine that I just bought is out of the machine, and the thermostat is certain.

If there is a problem, you need to go to the after-sales service for maintenance or go to the shopping mall to return it directly;

One is after using it for a period of time, which is usually when water enters the head of the soymilk machine during the cleaning process, and moisture enters the head for a long time during the heating process, causing problems with the computer chip. At this time, it is also necessary to find after-sales service to repair.

The soymilk machines on the market can usually be guaranteed for two years and provide door-to-door service. You can just hit **.

Confirm that the electric furnace wire is fault-free? Did you accidentally let the head of the soymilk machine get water when you cleaned it? There may be a short circuit inside, and it's best to look for after-sales maintenance. There are maintenance points everywhere, you can check the specific address on the official website, and they are free to repair during the 1-year warranty period.

There is a disconnect in the thermostat itself or in the circuit.

Summary. Hello dear, the soymilk machine only beats, but does not heat it: 1. It may be that too much water is put in, resulting in no heating; 2. It is possible that the circuit board has failed during use, and it will not be heated; 3. There may be a problem with the heating tube; 4. There may be a problem with the heated fuse, just replace it with a new heated fuse.

What is the reason why the soymilk machine only beats the pulp, but does not heat it?

Hello dear, the Doudan spring pulp machine only beats, but does not heat it is: 1. It may be that too much water is put in, resulting in no heating; 2. It is possible that the circuit board has failed in the process of making hail seepage resistant, and it will not be heated; 3. There may be a problem with the heating tube; 4. There may be a problem with the heated fuse, just replace it with a new heated fuse.

In this case, it is usually a problem with the heating tube.

Can be repaired but not. Yes.

However, you can only go to a professional maintenance place or contact after-sales service.

I've been buying it for several years, and I haven't used it for a long time.

Hmmm, it can be repaired too.

1. Check whether the water of the soymilk machine is added too much, which exceeds the maximum standard amount of the soymilk machine, resulting in no pulping.

2. More water in the soymilk machine will have an impact, and too little water will also affect the beating, so it is recommended to use the soymilk machine according to the amount specified in the manual.

3. If the soymilk machine blade is seriously worn, there will also be a phenomenon of non-pulping, and the soymilk machine blade can be replaced with a new one, or taken to the after-sales store to deal with it.

4. In addition, if the motor at the bottom of the soymilk machine is damaged, it will naturally not be able to rotate the pulp, and it is recommended to decide whether it is necessary to repair the motor according to the cost of maintenance.

The reason why the soymilk machine is not heated and how to maintain it

1) It may be due to too much water.

Maintenance method: according to the amount indicated on the instructions to discharge water, under normal circumstances, there will be two lines on the side of the soymilk machine, between that, try to let the amount of beans according to the amount of the instructions.

2) It is possible that the circuit board is faulty.

Maintenance method: first check whether the relay is still engaged when the program enters the heating process after powering on, and if it is not in the engagement, it is recommended to report for after-sales maintenance.

3) There may be a malfunction of the heating element.

Maintenance method: After turning off the electricity, use a universal meter to measure the poles of the heating element, if it is infinite, it means that the heating element is faulty, and replace it with the same model.

4) There is a pre-closing energy that can be used to heat the fuse pipe, so the balance crack occurs.

Maintenance method: first use a universal meter to measure whether the two ends of the fuse are connected, if not, it means that the heating fuse is faulty, and a heating fuse can be replaced.

Precautions for the use of soymilk machine

1. The soymilk machine should be placed on a stable table to avoid bumps and damage to the body.

2. In case of a sudden power failure, unplug the soymilk machine first. Avoid damage to the body caused by sudden calls.

3. After the power supply is connected, see if its working sound is normal, and whether there is a sound of pipes colliding with each other. If there is a relatively large abnormal sound, the power supply should be blocked immediately, and contact professional maintenance personnel.