Will there be a problem with sand grains when applying car film?

If the car film is not allowed to have sand grains, even if it is a small one, then the film is considered a blank paste. The best way is to choose a car beauty center with a dust-free workshop for film operation, they will generally help you wash the car carefully, and then carefully apply the film, and you can supervise the whole process on site.

If the dust inside the car film occupies a large area, it needs to be reattached. When the car film is pasted, if you find that there is dust in the film, it is best to go to the film repair shop in time to deal with it, because if the car film has dust, its viscosity will decrease, and in the process of high-speed driving, with time, the dust point will further expand, so it should be remedied in time. Don't handle it yourself, otherwise it may lead to a worse effect.

If there are sand grains in the car film, there is basically no way to solve it, and it is best to reapply the film. It is also very important to choose a film shop, it is best to choose a more professional place, with special equipment for film, professional technicians, and the film environment is generally a dust-free environment, which can reduce the appearance of sand, dust spots, etc., and in winter, the indoor temperature is about 15-30 °C, which is more conducive to filming.

Car film has a certain role in winter or summer, but many people mistakenly think that summer is more needed, but in fact, winter is also very needed. In winter, the content of the ozone layer decreases, and the intensity of ultraviolet rays will be greater, and the film can block a certain amount of ultraviolet rays, reduce the damage to the skin of the people in the car, and also alleviate the aging degree of the car interior. In addition, if the quality of the car film used is good, it can generally be used for about 5-10 years.

Summary. Hello dear, glad to answer for you! How to quickly remove air bubbles caused by dust and sand particles in car film There is no way to deal with impurity particles in the bubbles of car film, either it will be used, or it can only be replaced and repasted.

Hello dear, I'm glad to answer for you! How to quickly remove Lu Jing's bubbles due to dust and sand particles in the car film There is no way to deal with the impurity particles in the car film bubbles.

Dear, it is recommended that you choose a construction shop that can apply the film indoors for construction, otherwise it is easy for dust and spring grains to enter the film and land inspection, resulting in the inability to repair in the later stage.

Pro, 1If there is only a small amount of bubbles in the size of sesame seeds, you can test ignite and puncture it with a needle to squeeze out the inner skin and make it fit. 2.

When there are large bubbles or large bubbles, it is not recommended to deal with them by yourself, and decisively find a regular brand authorized store to replace them.

This is because there is debris on the glass that has not been cleaned up, and the only way is to restick it.

There are seven points to pay attention to in the film:

1. After the front windshield is pasted with the Wrigley film, try to dry in the direction of the sun when parking during the day, which will make the front windshield film dry faster. Generally, it takes about half a month to dry thoroughly, including the rear windshield.

2. After the car is pasted with the car film, avoid raising and lowering the windows within three days. Because there is still water between the window glass and the film that has just been pasted, it is easy to cause the edge of the film to fall off when the window glass is lifted, which will make the film unable to fit the glass again.

3. Do not wash the car within three days. Due to the high water pressure of professional car washing equipment, water is easy to be penetrated from the edge of the window, which will cause the edge of the glass and film to contain a large amount of water, and it will be easy to cause the edge of the Wrigley car film to fall off when the window is lifted and lowered after three days.

4. Do not open the sunroof when the vehicle has a sunroof within three days, especially when driving at high speed. When the sunroof is opened, convection occurs in the air inside and outside the car, which can easily cause the upper edge of the front windshield to fall off.

5. If you encounter blistering on the edge of the Wrigley car film, you should repair it at the construction point within 24 hours, and deal with it beyond the time, because the glue around the bubble has dried out, and the surrounding area of the car film can no longer move, and there will be creases during treatment.

6. It is forbidden to apply strong adhesive labels directly to the film within one month after the film, so as not to cause the partial detachment of the film from the glass.

7. After pasting Wrigley film in winter, it is recommended that you do not raise or lower the windows or wash the car within a week.

I have a front windshield, there is one just in front of the line of sight, I always feel uncomfortable, very small, my friends said that it does not affect, is it a psychological effect, I always drive unconsciously look at the small particles.

There are debris or particles between the film and the glass, it can only be said that the level of the film master is not professional enough, as long as it is pasted on the glass for more than 3 hours, it is basically impossible to repair, if it has just been pasted soon, you can find the shop that gives you the film to ask for re-pasting. But it is impossible to want to fix it, you can only ask for a repost.

Grain? Dirty, right? Or is it a matter of the quality of the membrane? There's no way to fix it, re-post it!

Oh, in fact, a little impurity has no effect on the film type, but people are like this, for their own things, always ask so perfect, the only way is to restick, but no one can guarantee that there is no small particles after repasting, can only see whether the heart of the film technician is fine enough, the master can reduce the impurities to a minimum, most of these particles are dust, because there is a lot of dust in the air, so a few years ago the film advocated dust-free film, In the environment of air humidity (cloudy day), the effect of the film will be a little better, mainly depending on the level of the technician!

Find them to pay or do it all over again.

The window frame must be wiped clean If it is the kind of wool of the Volkswagen, it must be stained with masking paper and can not be exposed at all The rest is that you hang it cleanly Indoors are not ventilated to be very clean Your hands and clothes must be clean These have been done There is also sand I admire There is also a little bit to remove the protective film quickly Try to keep the adhesive surface in the air for too long Because static electricity will also absorb some dust

Drive the car into a professional room, wipe it clean, and it's ready to be pasted.

Find a clean place in a windless environment!

Whether the dust particles are in the film or in the air, whether they are stuck in or in the environment are numerous.

If there is a lot of dust in the film, there will be a large number of bubbles, which is abnormal, if there are very few bubbles, and it does not affect the use, this is within the allowable range, and the film master has a bad technology will paste a lot of dust, you can ask for replacement.

This is discussed in the film hand family forum, mainly because of the environment of film construction and some details.

Hello