-
Anonymous users2024-02-06Before installation, please check whether the installation of cut-out templates, pencils, glue (such as strong glue), fastening splints (such as two-finger-wide marble blocks), faucets, soap dispensers and other optional accessories are ready.
Installation Steps. 1. Place the installation opening template flat on the counter surface of the cabinet and adjust the opening position, which requires attention to two problems
One is to determine that there is enough space to install the faucet, and the other is to determine that there is enough space to install fastening splints (or hooks), etc.;
2. Use a pencil to draw a line along the edge of the perforated cardboard on the countertop;
3.Hole according to the drawing line;
4.After the hole is opened, the countertop of the cabinet is turned over, and the prepared glue is evenly applied to the perimeter of the countertop opening.
5.Then fix the sink to the countertop;
6.Then glue several fastening cleats around the perimeter of the sink to strengthen the bond.
7.Replace the countertop with the cabinet and remove the exposed glue watermark before installing the faucet and drain fittings.
Most of the sinks are installed when the new house is renovated, and once the new house decoration is completed, there will be a comprehensive cleaning work, including cleaning the walls and floors of cement slag, wall glue, sediment, iron filings, paint and other sundries, and these sundries will form a rust-causing agent if they remain on the surface of the sink for a long time, causing floating rust or sticking to the surface of the sink and making it difficult to clean, thus affecting the image of Juyi products, so certain protective measures should be taken for the sink and faucet immediately after the installation of the sink.
The specific requirements are as follows:
1.The sink and its accessories must be cleaned up after the installation and successful water test, if not used for a long time, the water mixed with a small amount of dust impurities will leave a watermark on the surface of the sink that is difficult to clean after evaporation;
2.The faucet must be wrapped in the original packaging cloth bag;
3.In order to prevent customers from damaging the basin in the follow-up decoration process, such as preventing high-temperature welding slag, rusty iron slag, lime slurry, paint and coating from falling into the sink, you can dig a faucet hole in the sink carton, and completely cover the carton above the sink, because the carton is thicker, so that it can play a good protective role, of course, if it is equipped with text logos such as "please protect the sink during decoration and clean it in time after use".
-
Anonymous users2024-02-051. First of all, remove the plastic nut of the drainer under the basin and unscrew it counterclockwise, and take out the sealing washer.
2. Check whether there is sealant around the basin hole and between the flapper, under normal circumstances, the sealant will be played, and we can use a utility knife to cut it and clean it.
3. After the sealant is removed, push the drainer up from the bottom of the basin and take it out from the top of the basin.
How to replace the drain of the toto basin flap.
Wait for the basin sewer to be replaced: 1. Rotate the nut of the sewer, 2. Put the sewer into the basin hole, and then screw the nut back from below, to tighten, 3 connect the pipe to the sewer at one end and connect the sewer hole on the ground at one end.
No, yes, it's this case, and I want to change the flap cover.
1. First of all, remove the plastic nut of the drainer under the basin and unscrew it counterclockwise, and take out the sealing washer. 2. Check whether there is sealant around the basin hole and between the flapper, under normal circumstances, the sealant will be played, and we can use a utility knife to cut it and clean it. 3. After the sealant is removed, push the drainer up from the bottom of the basin and take it out from the top of the basin.
Pull it out the net, can't you pull it out?
Can't pull it out. It's like there's a location card.
I'll check it out for you.
Try it with pliers, it's really not good, just hit the repair**.
Left face cover] can't help it.
1. First of all, you need to know the memory supported by the motherboard and whether there are any remaining memory outlets. >>>More
005 Computer Principles and Disassembly 05 How to Install the Motherboard.
First, the material. There are many materials for the washbasin on the market, including marble, granite, artificial stone, stainless steel, mosaic, glass, ceramics, etc., how to choose so many materials. Among the five elements of Feng Shui, ceramics belong to the earth, and the handwashing station itself belongs to the water, the soil can overcome the water, and the ceramic material of the handwashing station can help remove the filth. >>>More
First, use the appropriate tools to make holes in the ceiling according to the corresponding lamp size. Second, correctly connect the wires and the terminal of the lamp in accordance with the instruction manual, it is best to install and operate by a professional electrician, please follow the safety rules of wiring. Third, use your hands to insert the snap buckles at both ends of the slim LED downlight vertically into the ceiling cutouts that match their size. >>>More
Paste their answers first, and then add some additions.
The function of the CPU fan is to dissipate heat from the CPU (it is a must, so that your CPU can work efficiently). >>>More