How to change the battery of LETV mobile phone? How to change the battery of LETV 2 mobile phone

The steps are as follows: 1. Use a hair dryer to blow around the phone for about 5 minutes, as shown in the figure below.

2. Slowly warp one side, be slow, use a wallpaper knife to warp a little and then use a crowbar.

3. Be sure to start on the edge of the phone, see it, pry it here.

4. Slowly pry it up and remove the cables and screws, remember how to install it.

5. Finally see the battery, remove the cable, be careful with the one above.

6. To replace the battery, first disassemble the screen, as shown in the figure below.

<>8. Turn on the battery first, and then install it normally, don't disassemble it if it's not good.

The steps to change the battery of a LETV mobile phone are as follows:

1. Use a screwdriver to unscrew the two screws at the bottom, and use a hair dryer to heat up the mobile phone to preheat and degum the waterproof glue.

2. Use suction cups, cards and other tools to gently warp from the top of the phone.

3. After opening, you will see that the middle position is the screen cable part, unscrew the two screws, and remove the display screen.

<>4. Unscrew the screws around and remove the middle partition plate.

5. Remove the battery, open the battery interface plug-in, replace the new battery, cover the middle spacer, and screw back the screws.

6. Finally, stick back the waterproof glue and it can be completed.

LETV mobile phone 3 machines can't remove the battery, you don't have to think about it. It's all one machine.

LETV mobile phones use an all-in-one design, so the battery cannot be replaced directly.

LETV mobile phones are all integrated design, and the battery cannot be replaced directly.

It is recommended to go to a mobile phone repair shop,If you change it yourself,LETV mobile phone can replace the battery as long as the back cover can be removed,The following are the specific steps。

First of all, you can use suction cups, cards and other tools to gently open the top of the phone from the top of the phone and open the phone cover.

Then unscrew the screws around the perimeter and remove the center partition.

Remove the battery, open the battery connector plug-in, and replace it with a new one. Cover back the central spacer. Screw back the screws.

Finally, the back cover is installed.

1、Take a hair dryer and turn on the hot air to blow on the screen of LETV 2 mobile phone for 1-2 minutes,The glue between the screen and the back cover melts,It is conducive to disassembly。

2、Take a knife and draw a circle along the edge of the LETV 2 mobile phone screen,Make a gap between the screen and the back cover。

3. Use inserts or stiffer pieces of paper to insert into the gap drawn by the upper type, and slowly expand the gap.

4. Separate the screen and the back cover to obtain a larger gap, and a row of lines can be seen at this time. Dust Brigade.

5. Use a screwdriver to remove the screws in the red box in the figure, which are used to fix the cables of the screen and the back cover components, and remove the screws to remove the screen.

6. Remove all the screws in the red box in the picture.

7. After completing the previous step, you can take away the protective plate covered by Bu Brother Dan on the battery.

8. Remove the old battery and replace it with a new battery, and carefully press it with your hand to make the new battery completely close to the back cover, otherwise the protection board cannot be installed back.

9. Replace all components and turn on the machine. Successfully booted,LETV 2The mobile phone successfully replaced the battery,It's done。

LeTV mobile phoneThe replacement card can be replaced by taking the card out with a pin. Do not use non-standard cards such as nano+ card holders, manual card cutting, etc., otherwise it will cause damage to the card holder, do not know the card, the SIM card cannot be removed, and do not insert and remove the card in the boot state.

You can press the SIM card holder to the end, and a click indicates that the card is installed correctly. The way to take out the card slot is to use the card pin to poke the card tray hole vertically, and do not install the TF card or SD card to install it and damage the card slot.

Development of a quiet spring history.

LeEco launched a smartphone after the impressive performance of the smart TV cautious business. LETV Mobile hopes to reduce people's attention to LETV mobile phones through covert research and development, and continue to increase the ecosystem. At the same time, through the introduction of experienced management and grassroots R&D personnel, we strive to avoid detours and improve their success chances.

On April 14, 2015, LETV released three flagship products of the dual flagship series of mobile phones in Beijing, namely LE1 series, LETV super mobile phone, LETV super mobile phone1pro, and LETV MAX series, LETV super mobile phoneMAX.

On October 27, 2015, LETV released Lekuanyun Jishi super mobile phone 1S, using the pricing method of ecological subsidy hardware, which is lower than the cost of mass production, and the price is 1099 yuan. 2016year4month20day,LETV officially released the super mobile phone 2nd generation series of new products Le2,Le2PRO and LEMAX2,2016year9month21day,LETV released a new generation of flagship products LEPRO3。

Hello dear<>

We are happy to serve you, and the answers are <> below

How to change the battery of LETV mobile phone X5oo is as followsThe steps for changing the battery of LETV mobile phone are as follows:1、Use a screwdriver to unscrew the bottom two screws,Use a hair dryer to heat up the phone around it,Make the waterproof glue preheat and degum。 2. Use suction cups, cards and other tools to gently open the lead from the top of the mobile phone.

3. After opening, you will see that the middle position is the screen cable part, unscrew the two traced screws, and remove the display screen. <>4. Unscrew the screws around and remove the middle partition plate. 5. Remove the battery, open the battery interface plug-in, replace the new battery, cover the middle spacer, and screw back.

6. Finally, stick back the waterproof glue and it can be completed.

Yes, you can change it.

How to change the built-in battery of LETV mobile phone: turn off - remove the screws of the mobile phone - remove the back cover from the suction cup - remove the cable.

Specific steps: 1. Shut down and take the card tray.

2. Disassemble the back cover, remove the tail screws, and with the assistance of the suction cup, remove the back cover 3, and remove the two fixing screws at the tail.

5. Remove the screws.

6. Remove the fixed iron sheet.

7. Pry off the headphone hole cable.

8. Take out the signal cable.

9. Remove the motherboard screws.

10. Pry off the vibrating motor cable.

11. Disconnect the antenna.

12. Pry open the LCD link cable.

13. Pry out the battery.

14. Change to another battery.

The mobile phone is an all-in-one machine that cannot be disassembled, but don't disassemble it yourself, the mobile phone is a one-year warranty for the battery, and it can be returned to the factory for repair or to the nearest after-sales outlet for repair.