How to clean the fan blades of the Xiaomi air purifier, how to disassemble and wash the fan of the X

Now the environmental pollution is serious, I believe that many families have bought air purifiers, but after using the air purifier for a period of time, I found that the blades of the purifier are very dirty, but I don't know how to open it, and I am afraid that I will dismantle it myself, so today I will teach you how to disassemble the millet purifier to clean the blades.

Tools Raw materials.

more, Xiaomi Air Cleaner Slotted Screwdriver Phillips Screwdriver.

Method steps.

1 6 Step by Step Reading.

The first thing to do is to unplug the power cord and then take out the filter cartridge and wipe it, which is relatively simple.

Then we turned the purifier over, took off the rubber buckles, and then we could see a circuit board, and we could remove it by unscrewing the screws with a screwdriver.

See the remaining 2 images.

Then there is the side panel, first pry the back with a flathead screwdriver, and then carefully remove the side panel, note that brute force cannot be used here.

See the remaining 2 images.

Then you can see that there are 4 screws in the fan cover, unscrew it and then remove the wires next to it, all of which have a foolproof design, don't worry about forgetting how to plug in.

See 1 image remaining.

Then remove the fan cover, unscrew the screws, remove the circuit board, and remove the fan blades.

See the remaining 3 images.

Then wash the removed fan blades with water or dish soap, wash and dry, and then put them back in the previous steps.

See 1 image remaining. Summary.

Unplug the power cord and wipe the cartridge.

Turn the purifier over, remove the rubber buckle, unscrew the screws and remove the circuit board.

Pry off the back of the side panel with a screwdriver and remove.

Unscrew the fan cover screws and remove all the cables on the side.

Remove the fan cover, unscrew the screws, remove the circuit board, and remove the fan blades.

Finally, clean the fan blades.

Precautions. Remember to pry from behind before opening the back, and don't use brute force.

Taking the Xiaomi air purifier as an example, the disassembly and cleaning method is as follows:

Rotate the top fan grille counterclockwise and remove it (please remove the operating instructions sticker first);

Hold the fan blade with one hand and unscrew the fan blade cover clockwise with the other hand to remove the fan.

Just clean it;

In order to ensure dynamic balance, it is not recommended to remove the label from the blade.

How to clean the Xiaomi purifier? The three-leaf millet purifier can be used to open the back cover with the screw skin of the special page, remove the fan blades, clean them with washing liquid, and install them to resume normal operation, which is very simple and easy to operate.

There should be a professional cleaning tool.

1.Disconnect the power supply (actually step 2: Turn on the fan grille purifier.)

will stop running, but for safety reasons, be sure to unplug the power plug); Open the fan grille and gently twist the grille counterclockwise with both hands and it will float.

2. Unscrew the top cover, which is to rotate the gray cover in the middle of the fan clockwise.

3. Lift the fan blades upwards to see if there is a bayonet on the back of the fan, which fits the transmission shaft just right.

on the card stick. <>

4. Replace the fan and gently rotate it a few times so that the fan and the transmission shaft are consistent; Gently screw the top cover of the fan counterclockwise, just screw it gently, if the fan is too tight, it may be unbalanced, and if it is a little looser, you don't have to worry about the fan coming loose, because the top cover is a reverse thread, and it will only get tighter and tighter as the fan turns.

Yes, I bought an air purifier for more than a year and used it recently, which may be caused by the speed adjustment when it is up and down, or it may be cracked because I put the air purifier under the lack of pads, which causes the maple leaves to resonate, resulting in all the damage of the maple leaves.

Later, I bought the relevant accessories through the universal template, and finally spent a long time when disassembling and dismantling, and finally found the trick to remove this fan, that is, you need to wear plastic gloves when disassembling to increase friction.

It was easily removed.

The details of the Xiaomi fan are as follows::Tools: Xiaomi fan, screwdriver. 1. Disconnect the power supply, unscrew the screws fixing the fan, and rotate counterclockwise to remove the front cover.

2. You can use a flat-edged screwdriver to unscrew the screws of the fan cover.

3. Gently pry along the gap in the circumference.

4. After the circumferential gaps become larger, pry a few more times to remove the lid, and then wipe it clean.

Tool Material: Mi Purifier.

Crowbars, screwdrivers.

1. First of all, cut off the four foot pads of the base of the Xiaomi purifier.

2. Then unscrew the screws on the base of the Mi purifier.

3. After that, remove the base of the Xiaomi purifier to expose the power strip.

4. Then use a crowbar to pry open the side baffle.

5. After that, open the air duct of the Mi purifier.

6. Then remove the fan blades of the Mi purifier.

7. Finally, clean the fan blades of the millet purifier.

Tools Materials: Xiaomi purifier, crowbar, screwdriver.

1. First of all, cut off the four foot pads of the base of the Xiaomi purifier.

2. Then unscrew the screws on the base of the Mi purifier.

3. After that, remove the base of the Xiaomi purifier to expose the power strip.

4. Then use a crowbar to pry open the side baffle.

5. After that, open the air duct of the Mi purifier. <>

6. Then remove the fan blades of the Mi purifier.

7. Finally, clean the fan blades of the millet purifier.