How to solve LAN not flashing? lan1 does not flicker, and it is always on, and you can t access the

If the LAN light does not turn on (off), the solution is as follows:

1. Check whether the network cable is plugged in tightly.

2. Check whether the port connection is correct.

3. Check whether the network card, computer or wireless router is broken.

If your problem is not solved through the above methods, you can log in to the online business hall of China Unicom, click "Broadband", "Broadband> "Broadband Service> "Broadband Fault Report" > "** Fault Report" on the home page to report the fault. The above path is subject to the actual information displayed on the query page.

Summary. Hello dear. Don't worry. Check the equipment first for the following points.

Check if the line connection is correct;

Check whether the network cable and the copper sheet of the crystal head are corroded;

Check if the bayonet is loose;

If there is a condition, change one and then connect it;

If the above situation is still not resolved, it is recommended that you contact your broadband communication operator.

lan1 does not flicker, and it is always on, and you can't access the Internet

Hello dear. Don't worry. First, call the following checks on the equipment.

1.Check if the line connection is correct; 2.Check whether the chain in the network cable and the copper sheet of the crystal head are corroded; 3.

Check if the bayonet is loose; 4.If the selling brother has the conditions to change one and then connect it; 5.If the above situation is still not resolved, it is recommended that you contact your broadband communication operator.

I hope mine can help you. If you have any other questions, you can also ask me, I'm always on <>

When the LAN light keeps flashing and the computer cannot connect to the network, it may be caused by the following reasons:

Network faults: Flashing LAN lights may indicate a problem with the network connection, such as an unstable network cable connection, a faulty router, or a misconfigured network device. You can try plugging the network cable back in, check the status of your router or other network device, and make sure it's working properly.

Rent a room. IP address issue: The computer may not be able to obtain a valid IP address, resulting in the inability to connect to the network. You can try using DHCP (Dynamic Host Configuration Protocol) on your computer to get an IP address, or you can manually set the correct IP address, subnet mask, and default gateway.

Firewall settings: Firewall software or security settings may prevent your computer from communicating with the network. You can check the firewall settings on your computer and make sure that the relevant applications and ports that communicate with the network are allowed to be hidden.

Network driver issues: The network adapter's drivers may need to be updated or have issues that prevent you from connecting to the network properly. You can try Sakura to update the driver for your network adapter, or reinstall the driver to fix the underlying issue.

Network configuration issues: There may be a problem with your computer's network configuration, such as incorrect DNS server settings or gateway settings. You can check the network settings on your computer and make sure they match your network environment.

If you have tried the above methods and still cannot solve the problem, it is recommended that you contact the technical support of the network equipment manufacturer or consult a professional for further assistance. They can provide more detailed diagnoses and solutions on a case-by-case basis.

If your network lan2 light is solid and lan1 is flashing, and there is no network connection, try the following steps to fix the problem:1Check the network cable connection:

Make sure that the network cables for the LAN1 and LAN2 ports are plugged in correctly. It could be due to a loose or damaged network cable causing the connection issue. (This is more likely) 2

Restart the router: Power off the router and wait for about 30 seconds, then power it on again. This leak will refresh the device and help resolve some temporary network issues.

Make sure the DHCP server on your router is working properly. DHCP is responsible for assigning IP addresses and other network settings to your devices. Check the DHCP configuration in the router settings and make sure it is enabled.

Contact your ISP: If none of the above methods resolve the issue, then your ISP may be faulty. Contact your ISP to report the issue to them and ask for further help and support.

Note that these are common troubleshooting steps, but the exact workaround may vary depending on your network device and settings.

Hello, if your network lan2 indicator is solid and lan1 indicator is flashing, and you can't surf the internet, you can try the following solutions:1Check your network connection:

Make sure your network cable is properly connected to the LAN2 port and connected to the correct network device (such as a router or switch). 2.Restart the network device

Try restarting your router or switch. Power off and wait a few minutes before turning it back on. After the device is fully powered up, check the status of the LAN1 and LAN2 LEDs.

Sometimes, a damaged or low-quality network cable can cause connectivity issues. Try replacing the network cable and see if there is any improvement. 5.

Check network device configuration: Check the configuration of your router or switch to make sure that both the LAN1 and LAN2 ports are working properly and that there are no special settings blocking internet access. 6.

Reset your network device: If none of the above fixes the issue, you can try restoring your router or switch to factory settings. Note that this will clear all custom configurations, make sure you have backed up important configuration information.

If the problem persists, it is recommended to contact your network service provider or technical support from the network equipment manufacturer, who may be able to do it for you.

Summary. Kiss <>

Hello, the teacher will reply for you: If the network lan2 is always on and lan1 is flashing, it means that there is a problem with the network connection of the lan1 port, which may be a network line failure or a device configuration problem. Here's how to fix it:

1.Check the network cable: Make sure that the network cable of the LAN1 port is properly connected and is not loose or damaged.

You can try to change the network cable for testing. 2.Check the device configuration:

Check whether the devices on LAN 1 are correctly configured with network parameters such as IP addresses, subnet masks, and gateways. You can try restarting your device or doing a factory reset. 3.

Check network devices: Check the status of routers, switches, or other network devices to ensure that they are working properly. You can try restarting your network device.

If none of the above methods solve the problem, it is recommended to contact the network operator or network technical support personnel for further diagnosis and repair. <>

What should I do if the network lan2 is always on and lan1 is flashing and there is no network.

Kiss <>

Hello, the teacher will reply for you: If the network lan2 is always on and lan1 is flashing, it means that the network connection of lan1 port has a fluttering pin problem, which may be a network line failure or a device configuration problem. Here's how to fix it:

1.Check the network cable: Make sure that the network cable of the LAN1 port is properly connected and is not loose or damaged.

You can try to change the network cable for testing. 2.Check the device configuration:

Check whether the network parameters such as IP address, subnet mask, and gateway are correctly configured on the LAN 1 port. You can try restarting your device or doing a factory reset. 3.

Check network devices: Check the status of routers, switches, or other network devices to ensure that they are working properly. You can try restarting your network device.

If none of the above methods solve the problem, it is recommended to contact the network operator or network technical support personnel for further diagnosis and repair. <>

Okay thank you. Kiss <>

The teacher has sorted out the relevant expansion Yinlu for you: To set up a home network, you first need to choose a suitable router to ensure that its coverage can meet the needs of the area where the home is bright. Then connect the router with your broadband modem, plug it in and turn it on.

Next, connect to your router's wireless network from your computer or phone, enter your router's IP address in your browser, and follow the instructions to set it up. You can set the wireless network name and password, as well as other network parameters. Alternatively, network taps or bridges can be used to extend the reach of your home network.

In order to improve the integrity of the network, it is also possible to set the separation of the guest network and the home network. In addition, it is also necessary to understand some cyber security knowledge, such as regularly changing wireless network passwords and using strong passwords.