Whirlpool 24708BW washing machine shows what is the fault of 8yE?

Indicates the extent to which the garment has been washed. It is a special instrument to measure the reflectivity of the polluted cloth, and the reference cloth to compare the data obtained, China's national manufacturing standards stipulate that the qualified value is, to achieve the first level of energy efficiency.

F1: Poor contact with the water level sensor.

E1: When the drain times out, check whether the drain pipe is blocked or the safety switch is faulty. It means that the imbalance of the two dehydrations cannot be handled automatically, so please place the clothes evenly and cover the cover by hand.

Or the cover plate is not covered when running, please cover the cover plate. The washing machine continues to run automatically. Maintained until manual intervention"e1"Display status.

E2: The lid is not properly covered.

E3: Unbalanced dehydration, shake the clothes back up and dehydrate again. Indicates that the drain time is more than 5 minutes.

It may be that the drain pipe is not put down, blocked, or frozen, please put down or unclog the drain pipe, open and close the cover once, and the washing machine can continue to work. If no one intervenes, the washing machine will automatically turn off the power after about an hour.

E4: When the water inlet is overtime, check the water pressure and whether the water inlet valve is dirty and blocked. It means that the set water level has not been reached after 30 minutes of water ingress.

As in the instructions"Washing does not work"After the condition is checked, the cover can be opened and closed once the water can be restored. If no one intervenes, the laundry will automatically turn off the power and shut down after about 1 hour.

E5: The water temperature is over 50 degrees.

In this case, if this thing is displayed, it means that the line is short-circuited, and it is this fault, which is because of this.

The washing machine displays 777, which means that the alarm is faulty, and the communication between the display board chip and the main control chip is abnormal, and the board chip needs to be replaced.

The water inlet must exceed the set water level before the water can be entered: the air pressure in the air pressure switch gas collection chamber still does not reach the specified value, and the water can not be entered, the reason may be that the air guide nozzle of the gas collection chamber is blocked, and the foreign matter needs to be removed, and check whether the nozzle is leaking, if there is air leakage, replace it in time.

The washing machine kept pouring water. The main reasons are as follows:1. The connecting pipe of the water level switch falls off, and the switch cannot get a signal to prevent it from falling off again. If the pipe does not fall off, it is recommended to replace the water level switch.

It's the same in my house, I unplug the power and disassemble the top plate, use a hair dryer to dry the computer for a few minutes, and then press it back on, you can try it.

If the Whirlpool washing machine fails to show this situation, you can contact the official after-sales service.

The 777 of the washing machine means that the alarm is faulty, and the communication between the display board chip and the main control chip is abnormal, and the board chip needs to be replaced. The water inlet must exceed the set water level before water can be entered: the air pressure in the gas collection chamber of the water pressure switch still does not reach the specified value, and the water can not be entered, the reason may be that the air nozzle of the gas collection chamber is blocked, and the foreign matter needs to be removed, and check whether the nozzle is leaking, if there is air leakage, replace it in time.

The reasons for 777 may be:

1.Control panel failure: When the 777 error code appears on the washing machine, it may be due to the failure of the control board, resulting in the failure of the washing machine.

2.Water pressure is too low: When the water pressure is too low, it will also cause the 777 error code to appear on the pin of the washing machine, at this time, you should check whether the water pressure is normal and take measures to increase the water pressure.

3.Abnormal water temperature: If the washing machine has a 777 error code, it may be due to the water temperature being too low or too high, and you should check whether the water temperature is normal.

4.Abnormal voltage: When the 777 error code appears in the washing machine, it may be because the voltage is too low or too high.

The washing machine shows that the F08 fault is a faulty heating tube (or thermostat fault) The possible causes include: the heating tube is broken, the wiring harness between the heating tube and the computer board is open or short, and the computer board heating unit is faulty.

The handling method of F08 fault ** is as follows:

1. Check whether the water level sensor is abnormal, most of it is caused by the humid environment, it is recommended to disassemble the control panel base, first use a hair dryer to blow and see, the general situation can be solved.

2. The connection between the water level sensor and the socket on the computer board is not good, so it is recommended to adjust and re-plug it.

3. The plug of the water level sensor is not in good contact with the water level sensor, so it is recommended to adjust and re-plug it.

4. If the detection circuit of the computer board fails, it is recommended to repair or replace the computer board.

5. If the internal fault of the water level sensor is faulty, it is recommended to replace the water level sensor.

First, Whirlpool washing machine failure **F08 is a heating pipe failure.

Second, the fault handling method: replace the heating wire to remove the fault.

There is a table on the title page of the manual, and it is all written on it

It is recommended that you check the display panel for water ingress.

If the motor does not turn and it whines, the motor or capacitor may be damaged. At this point, set the washing machine to the washing state. When the motor whines, apply a force (clockwise force only) to the wave wheel with your hand.

If the wave wheel can be turned by hand, the starter capacitor is disconnected. If the afterburner does not rotate and the wave wheel dies, the motor is broken.

Whirlpool washing machine failure, in this case, you can contact the official after-sales customer service.

1.The communication between the panel and the motherboard is old, and the voltage is too low. Please check the power supply voltage and motherboard.

2.If the water level sensor is damaged or in poor contact, check whether the water level sensor and its circuit are connected, observe whether the air duct is flooded, and replace it if necessary. Two.

Failure of Whirlpool washing machine E8. 1.The failure of Whirlpool washing machine E8 is a bad code fault code due to damage or poor contact of the water level sensor; 2.

If you encounter this kind of failure, you can try to check the filter in the washing machine to see if there is any debris, whether it has not been cleaned for a long time, and turn it over clean; 3.Use a tool to pry open the drain under the washing machine, first use a basin to put the prepared sewage below to flow out, and then directly screw the lid after opening to catch the sewage and discharge it; 4.If the above removal measures can not be solved, it may be caused by the failure of the water level sensor or circuit board detection circuit, and it can only be repaired or replaced, and it is recommended to find after-sales maintenance personnel to repair it.