LAN1 is connected to the router, LAN2 is connected to the TV set top box, LAN1 s light does not flas

Settings - Wi-Fi - Search for your wifi - Enter password - Connect. In addition, it is recommended that you install the sofa butler, which can **a lot of film and television software, almost what you want to watch**, movies, TV series.

If your network lan2 light is solid and lan1 is flashing, and there is no network connection, try the following steps to fix the problem:1Check the network cable connection:

Make sure that the network cables for the LAN1 and LAN2 ports are plugged in correctly. It could be due to a loose or damaged network cable causing the connection issue. (This is more likely) 2

Restart the router: Power off the router and wait for about 30 seconds, then power it on again. This leak will refresh the device and help resolve some temporary network issues.

Make sure the DHCP server on your router is working properly. DHCP is responsible for assigning IP addresses and other network settings to your devices. Check the DHCP configuration in the router settings and make sure it is enabled.

Contact your ISP: If none of the above methods resolve the issue, then your ISP may be faulty. Contact your ISP to report the issue to them and ask for further help and support.

Note that these are common troubleshooting steps, but the exact workaround may vary depending on your network device and settings.

Summary. Kiss <>

Hello, the teacher will reply for you: If the network lan2 is always on and lan1 is flashing, it means that there is a problem with the network connection of the lan1 port, which may be a network line failure or a device configuration problem. Here's how to fix it:

1.Check the network cable: Make sure that the network cable of the LAN1 port is properly connected and is not loose or damaged.

You can try to change the network cable for testing. 2.Check the device configuration:

Check whether the devices on LAN 1 are correctly configured with network parameters such as IP addresses, subnet masks, and gateways. You can try restarting your device or doing a factory reset. 3.

Check network devices: Check the status of routers, switches, or other network devices to ensure that they are working properly. You can try restarting your network device.

If none of the above methods solve the problem, it is recommended to contact the network operator or network technical support personnel for further diagnosis and repair. <>

What should I do if the network lan2 is always on and lan1 is flashing and there is no network.

Kiss <>

Hello, the teacher will reply for you: If the network lan2 is always on and lan1 is flashing, it means that the network connection of lan1 port has a fluttering pin problem, which may be a network line failure or a device configuration problem. Here's how to fix it:

1.Check the network cable: Make sure that the network cable of the LAN1 port is properly connected and is not loose or damaged.

You can try to change the network cable for testing. 2.Check the device configuration:

Check whether the network parameters such as IP address, subnet mask, and gateway are correctly configured on the LAN 1 port. You can try restarting your device or doing a factory reset. 3.

Check network devices: Check the status of routers, switches, or other network devices to ensure that they are working properly. You can try restarting your network device.

If none of the above methods solve the problem, it is recommended to contact the network operator or network technical support personnel for further diagnosis and repair. <>

Okay thank you. Kiss <>

The teacher has sorted out the relevant expansion Yinlu for you: To set up a home network, you first need to choose a suitable router to ensure that its coverage can meet the needs of the area where the home is bright. Then connect the router with your broadband modem, plug it in and turn it on.

Next, connect to your router's wireless network from your computer or phone, enter your router's IP address in your browser, and follow the instructions to set it up. You can set the wireless network name and password, as well as other network parameters. Alternatively, network taps or bridges can be used to extend the reach of your home network.

In order to improve the integrity of the network, it is also possible to set the separation of the guest network and the home network. In addition, it is also necessary to understand some cyber security knowledge, such as regularly changing wireless network passwords and using strong passwords.

Hello, if your network lan2 indicator is solid and lan1 indicator is flashing, and you can't surf the internet, you can try the following solutions:1Check your network connection:

Make sure your network cable is properly connected to the LAN2 port and connected to the correct network device (such as a router or switch). 2.Restart the network device

Try restarting your router or switch. Power off and wait a few minutes before turning it back on. After the device is fully powered up, check the status of the LAN1 and LAN2 LEDs.

Sometimes, a damaged or low-quality network cable can cause connectivity issues. Try replacing the network cable and see if there is any improvement. 5.

Check network device configuration: Check the configuration of your router or switch to make sure that both the LAN1 and LAN2 ports are working properly and that there are no special settings blocking internet access. 6.

Reset your network device: If none of the above fixes the issue, you can try restoring your router or switch to factory settings. Note that this will clear all custom configurations, make sure you have backed up important configuration information.

If the problem persists, it is recommended to contact your network service provider or technical support from the network equipment manufacturer, who may be able to do it for you.

lan1 light flashing + can connect to wifi but it doesn't work.

Hello, dear, I've kept you waiting, and now I'll answer for you. LAN 1 light flashes + can connect to wifi but can't use the reason and solution:1

For broadband issues, connect a broadband cable directly to test whether there is a network speed. If it doesn't work, contact broadband customer service to solve it; 2.If there is a problem with the router, you can cut off the pure power supply of the router and wait for a period of time before connecting.

If you still don't have the internet speed, you can restore the factory settings and reset the router according to the instructions for lifting the bucket. 4. If there is a problem with the LAN 1 system, you can go to the maintenance office to restore or reinstall the system. Additional reading:1

First of all, we use our mobile phone to connect to the device to check whether the Internet is normal. 2.If the internet is fine, we log in to the router.

3.We check if the WAN port in the router is normal, and then we have to click on the button to set the LAN port. 4. We click the network port setting button to enter the network port setting page.

5.On the settings page, we see that the IP address of the LAN port is set to manual, and generally we can set it to automatic. 6.

Next, we set the IP address of the LAN port to automatically connect to the Internet.

Hello, if it's a light cat.

If the LOS light turns red or the hall flashes, it is usually caused by the following conditions:

If there is a problem with the optical interface of the optical modem, you need to replace the optical modem.

Indoor pigtails. The connector of the latching cat in the state of the base pin is loose, and the connector can be restored by plugging it in;

The bend of the optical fiber in the indoor part is too large. Excessive bending of the optical fiber will affect the total reflection of the optical signal in the optical fiber.

Transmission, as long as the optical fiber is straightened;

If the outdoor optical fiber is broken or the optical port of the equipment in the equipment room is faulty, you need to contact China Unicom staff to report the fault.

1. The network cable that comes out of the normal cat must be connected to the router WAN port, and then log in to the router to set the router WAN port configuration.

2. If the network cable out of your cat is connected to the router LAN port, and your computer can access the Internet without a broadband connection, it means that your "cat has a router function", then your router only plays the role of a switch, and the notebook cannot get the address, you need to manually add the address.

3. If your cat has a router function, you should connect the WAN port of the router and set the WAN port as a dynamic IP, after which your laptop and computer can access the Internet.