LCD display font has ghosting, how to solve, 50 points! Add 100 when solved!

The above statement makes sense, the display has an optimal fractional resolution, if you say that it is adjusted to 1024*768, it is fine, it means that this is your best. Also, you can turn your refresh rate up a little higher, if it's 60, or 75 or higher, depending on your monitor. Before trying the above again, you should first see if the VGA interface behind your monitor is loose, because I also had your reason last time, and it turned out to be a problem for a long time.

That's because the best resolution of your monitor is1024x768,It really has1024*768 liquid crystal dots,Turning it up or down will produce a bad display effect,Your monitor won't be displayed in the center,So ghosting,It's best to use the best resolution,Otherwise, it's not good for the display。

The LCD monitor has an optimal resolution! Only by jumping to the best resolution will it not blur! Your best resolution is 1024*786

If this problem occurs only when the pixels are expanded, it may be that the refresh rate is not enough, right-click on the blank space of the screen --Properties--Settings--Advanced--Monitor, and turn the refresh rate up to see.

This may be a phenomenon of screen burning,Like the previous CRT monitor, this phenomenon often occurs,Mainly because the monitor stays on the same screen for too long,A friend's monitor of mine is the same,Always like to watch network TV,As a result, a cctv5 logo appeared in the upper left corner of the screen later,No matter what interface you switch to, it won't disappear。 This situation is not good, but the color will not be so dark after a long time, and it can be used reluctantly. Note that when the desktop is not in use, enable the screensaver (automatically starts in about 5 minutes).

There is also a situation where there is a problem with the graphics card, which can be checked with special detection software.

1024 786 The settings are set like this, and if they are set like this, they will be blurry if they are higher, and if you want to change to something else, you need to install a discrete graphics card.

For some displays, auto (auto-adjustment) on the dot panel can be solved.

Reboot -- press F8 -- select the last correct configuration.

1. If the VGA cable is poorly connected, the host signal output is output to the display signal input, if the interface is not in good contact, it will cause the display image to be distorted and the color to be abnormal;

2. The refresh rate of the display is not enough, the default refresh rate of the domestic display is 60Hz, if the setting is low, the display image is refreshed and the image is incomplete.

It is recommended to re-plug the VGA port and set the refresh rate of the monitor to 60Hz.

Note: The refresh rate is set by Desktop --Properties --Settings--Advanced--Monitor--Screen Refresh Rate.

Mine is also this problem.,It's useless to reinstall the graphics card driver.,It's useless to adjust the resolution.,It's useless to adjust it.,I asked the customer service to come and take a look.,People got it in two clicks.,It's a long time and the connector is a little bit of poor contact.,You turn the data cable on the display over and plug it in with the end on the host.,Tighten it and try it.,That's how people got it for me.,Be sure to tighten it!

My monitor is an TPV 19" 1440x900

The graphics card is 9600gt

Press the auto button on the monitor panel once, and wait a few seconds for it to automatically adjust and you're done.

Try a different VGA cable, and try the power cable, to see if it's a problem with the display or the graphics card.

If the display has a warranty, take it to the warranty, and if not, repair it and see if the quality is too poor, and the screen is broken.

Has it rained lately? Maybe it's damp I've had the same thing with my computer.

It's OK to stand by for a while.

The LCD interface and the graphics card interface are not tightened, resulting in the problem of ghosting, check whether the lower interface is plugged in.

Adjust the resolution, maybe the video memory is not enough.

If it's a discrete graphics card, check your graphics card and install the driver.

To solve the problem of the font of the LCD monitor, the first thing is to check whether the resolution of the LCD is set correctly. LCD monitors will have an optimal resolution, just like a 19-inch widescreen LCD monitor is 1440*900 (some are 1680*1050), a 22-inch widescreen LCD monitor is 1680*1050, and when the resolution set by the user is not this optimal resolution, there will be a situation where the font is blurred.

If you can't find the best resolution for the LCD in the adjustment options, you need to install the driver of the graphics card first. This explains why most of the users who find fonts blurred do so after changing their graphics cards. Therefore, if you find that the LCD has a problem with the font blurring, please check whether the system resolution is set to the best resolution, if you can't find the best resolution in the adjustment items, then you must install the driver of the graphics card (including the integrated motherboard) correctly.

If you are sure that the resolution is set correctly, and the text is still blurred, then you need to adjust the LCD display yourself. The method is very simple, just press the "Auto" button on the LCD OSD menu directly (some LCD keys are implemented by combining keys), and its function is to make the LCD automatically adjust to make the text display sharper. Of course, this is only useful for analog signals (VGA), and if you are using a DVI signal line, it will not be very useful.

If the user's LCD OSD button does not have an "Auto" button, then it needs to be adjusted manually, generally the two options of "Pixel Clock" and "Phase Adjustment", which can be found in the LCD adjustment menu.

6win10 font blur is perfectly solved.

Possible reason 1: The resolution is not set to the best resolution for the LCD.

Generally beginner users will encounter such a problem, more senior players know that LCD monitors have their own most suitable resolution, which is determined by the physical structure of the LCD panel, for desktop computers, usually the best resolution of 15-inch LCD monitors is 12801024 inches.

Solution: Right-click on the desktop, select Properties, and then select the Settings tab, and now the lower left corner of the menu is the slider to adjust the resolution, drag it, adjust to the best resolution of the monitor, and then click Apply, the system will prompt whether to keep the changes, select OK.

Possible cause 2: The digital signal phase or pixel is set incorrectly.

This is less likely unless the signal phase and pixels have been misadjusted in the LCD control menu, or the output signal of the graphics card does not match the LCD display.

Solution: It is very simple, the control buttons on the LCD display panel can be adjusted to normal display. First choose self-image adjustment or factory reset, if the image is still blurry at this time, enter the image adjustment menu, manual adjustment of fine-tuning and clarity (also known as phase, pixel adjustment), the general LCD has a Chinese menu.

Swap and compare, take the monitor to your sister and try it to see if it's a problem with the monitor.

If it's a problem with the monitor, you'll find reset in the settings. Generally, the parameters are optimal when setting up at the factory.

If it's blurry again, it may have something to do with your display, you bought it 5 years ago, and the display screen is at least a product from 5 or 6 years ago, not LED, right?? The old display screen was not as good as the current display screen.

You can press ctrl and +- to resize the page.

An LCD monitor is a fixed-resolution display that works best only at the best resolution.

It's a pity that you have watched 1440*900 for 5 years, and you have long been used to the large font.

Of course! The best resolution for 22 inches is 1680x1050, and you are 1440 of course! Also use whether you are VGA or DVI, if it is VGA, then change to DVI.

If the monitor is installed on another computer, try to change the resolution, and it still doesn't work, then it can only be a problem with the graphics card.

Yes, it is generally caused by the aging of the VGA signal line.

Once you've ruled out resolution issues, consider display settings.

Step: The control keys on the LCD display panel – Other – Auto-Adjust – Yes.

This one is pretty much fine. To get better, do the following:

Right-click on the desktop - Personalize - Display - Adjust the clearType text, select according to the prompts, and finally click Confirm.

The reason why the text is ghosted on the computer may be due to the lack of refresh rate on the computer, or a problem with the cable.

The solution to the ghosting of computer text:

1. Right-click on the blank space of the desktop--Properties.

2. Click Open.

3. Click Appearance--Effect.

4. Check the following methods to make the year of the screen font smooth, and the following options are selected clearly - OK.

Experience for yourself, the quality of the VGA cable is very important for the display effect!!

It took 3-4 days to debug all sorts of debugging: updating the driver, resetting the resolution. Switch to a different computer for testing. Ghosting cannot be removed.

I've been using that garbage VGA cable to test the machine, thinking it's a display problem. Already planning to replace the monitor. And I also thought that the quality of the computer graphics card was too poor, and I was very annoyed.

In the end, it was a mistake, I found a VGA cable on the brand machine to access, the ghost disappeared, and the font display was very sharp! Only to find out that it was a problem with the wire.

Poor quality VGA cable, poor shielding or filtering, seriously affect the display effect. Especially in complex use environments, interference with transmitted signals is hidden.

If possible, first find a *** VGA data cable to access the test machine and take a look.

First try my computer right-click, properties, advanced system settings, performance settings, use the shadow on the desktop for icon labels to cancel, if it doesn't work, update the graphics card driver.

Generally, this situation is mostly a problem with the display,You can see if the display has the function of adjusting this aspect,You can look for it,If not,It is recommended to change the resolution to try,Generally, it can be solved。

Reset the screen settings to your appearance settings or make automatic adjustments.

Try restarting your computer first, and if you still have one, let your computer rest for a while, cool it down, and then restart it. This may happen when the computer is used for a long time and the heat dissipation is not very good. If there is still such a situation after resting and cooling, it is necessary to consider whether there is a fall and a knock, which may get the contact of the internal parts of the computer, such as the poor contact of the display screen, if this is the case, you need to take it to the store and find professional personnel to help repair it.

Of course, if the problem is not very big and does not affect the use, it is better to continue to use it and do not need to worry too much about this problem.

The specific solution to the ghosting on the computer screen is as follows:

Method 1: Reinsert the display cable.

1.When the computer is ghosted, first check the connection of the monitor cable.

3.Then the screen will return to normal.

Method 2: Modify the frequency.

1.Right-click on the screen and select "Screen Resolution".

2.Click on the blue word "Advanced Settings" in the bottom right corner.

3.Once you find "Monitor", change the screen refresh rate to 60Hz and tap "OK".

4.Then restart the computer and it will show normal results.

Reinstall the graphics card driver and reseat the memory module.

Update the graphics card driver or adjust the resolution.

Workaround for computer ghosting:

Right-click My Computer, click Properties Advanced Performance Settings, select Use Shadows for Icon Labels on the Desktop in the Visual Effects page, and click OK.

Right-click on the blank space of the desktop, and delete "Lock desktop web items" in the "Arrange icons".

Sometimes, the above settings do not solve the problem, and we can solve it by creating a new user, but the settings such as the desktop icon, quick launch bar, and environment variables will return to the default state and need to be set again.

Another way to solve the problem is to right-click on an empty space on the desktop, click on the Properties Desktop Customize Desktop Web option, and then drag the Current Home page in the Web page bar, and then http ....Wait for all the checks in front of each item to be removed ("http......"In order to add web pages or ** addresses from the Internet, generally not needed, you can delete them all), and remove the tick in front of the "lock desktop project" below, click OK to complete the setting, and you can see the cute desktop icon again.