In daily life, can the bathroom be directly tiled after waterproofing?

After the bathroom is waterproofed, it can not be directly tiled, and there should be a layer of cement sand and ash between the waterproof layer and the tiles. This is because the waterproof layer will not be easily replaced, the possible life will be the same as the life of the building, and the tile has cracking, replacement, if the waterproof layer is close to the tile, the waterproof layer will be accidentally damaged when replacing the tile, so the loss is large.

After the bathroom is waterproofed, it can be directly tiled, because of this, because of this, as long as your waterproofing is excellent, there is no problem.

It can not be pasted directly, and then it is necessary to do brushing treatment, otherwise the tile will not be firmly pasted, and it will fall down for a long time, and potential safety hazards will occur.

No, you cannot. Because the wall is too smooth after waterproofing, the tiles will fall off directly. The wall should be brushed and then tiled, so that it will not fall off.

If you can't directly paste the tile, it will fall off after a long time, and it is best to lay a layer of cement on top of the waterproof, and then paste the tile.

Can I directly paste tiles in the bathroom after waterproofing in daily life? In everyday life. After the waterproofing, it is completely possible to apply tiles. Do you have to try to leak if you are waterproof?

If the wall surface of the waterproof project is not brushed, the tile and the base surface will not be firmly bonded, and there will be a hollowing phenomenon in the later stage, and even the tile will fall off. The proportional component of brushing is to mix a small amount of glue with cement and stir evenly with a small amount of sand, and then use a brush to apply the stirred material to the wall surface of the waterproof project, highlighting the unevenness on the wall, so that the adhesion of the wall surface is effectively increased.

After the bathroom is waterproofed, put water on the bathroom floor, observe for 24 hours, and see if the downstairs leaks.

There is no such hypocrisy, the general procedure is that after the secondary waterproofing is done, you can directly paste the tiles!

The waterproof material painted on the wall is finally formed by a layer of coating film, and there are few pores on the surface of the coating film, almost no pores. Therefore, it is impossible to meet the requirements of wall tiles. Because the base layer of pasting tiles must have a certain porosity to meet the coagulation of the pasting material.

There are problems: The tiles pasted on the wall have serious hollowing problems in the later stage. And once there is a hollow drum, there will be a hollow drum of the tiles in the entire waterproof area.

Wall tiles are falling off. When the hollowing is severe to a certain extent, it will separate from the wall and cause the tiles to fall off.

Treatment measures: We must first check the strength of the wall base. That is to say, before brushing waterproofing, it is necessary to ensure that the base layer of the wall does not have problems such as sand, sand dropping, hollowing and so on.

On the finished surface of waterproofing, it is recommended that you take the method of spraying or brushing to increase the adhesion between the base layer and the adhesive material. Special adhesive materials are used to paste tiles with waterproof walls. For example, you can choose the tile adhesive that is more commonly used at present.

Tiles can be glued using the back of the tile. Before pasting the wall tiles, brush the "wall solid" twice on the waterproof layer, the wall fixing glue, good wettability, high bonding strength, mainly used for better pasting the tile with the waterproof layer, effectively preventing the hollow drum from falling off.

From the above steps, it can be seen that the wall of the bathroom should not only be waterproof, but also tiled, so that the waterproof work of the bathroom can be foolproof. Even fall off. If the wall has been waterproofed, if the brick is pasted, it is necessary to brush a good layer of back glue on the wall, and the back of the brick should also be brushed with a layer of back glue, which will be more firm and not easy to fall off.

The waterproof layer is used to prevent waterproofing, as long as there is a little crevice, water can drill into it, so we must protect the waterproof layer well. It is necessary to plaster, mortar and sweep on top of the waterproof layer, and use it for protection. Polyurethane waterproof material try not to be used on the wall will affect the later tile adhesion effect, the world's waterproof materials are tens of thousands, in order to avoid unnecessary trouble, give some personal advice, I hope it will be useful to you.

That is, after the hair is solidified, we use our hands to deduct the hair to see if there is a place to deduct it, if it can't be deducted, it means that the strength has arrived, there is no problem, otherwise it is unqualified. It is to use a special tile adhesive, which is selected according to the water absorption rate of the tile to paste the wall tiles. Tiles have a good heat absorption effect, and if the space temperature is high, it can effectively reduce the indoor temperature.

Of course, which one to choose depends on the specific characteristics of the house and regional differences, and you can't rush it.

It is the area of the shower room that we all know. The second part is the washbasin area in the bathroom. These two parts are required by the code to be waterproofed on the wall.

In addition, some friends have chosen the method of waterproofing all the interior walls of the bathroom, of course, it is also possible. After the waterproof layer is done 2 to 3 times, there will be a curing period of 5 to 7 days, so naturally, tiling must be done after this, so you can't stick tiles immediately after waterproofing. The bathroom wall is waterproof, and it can be tiled.

The key problem of tile sticking is not to operate according to the requirements of tiling.

Of course, it is needed, and tiling is also to make the walls of the bathroom look better, and it can also play a role in water insulation again.

OK. But before we apply tiles, we must use tile adhesive, which will be firmer and will not fall off.

Of course, you can paste tiles, but before pasting, you must level it, you must treat the wall, and you can also add barbed wire, which can make the tiles more firmly pasted and not easy to fall.

Yes, and the bathroom wall tiles are also conducive to cleaning, and it is also a decoration method that many young people will choose.

The bathroom wall has been coated with waterproof measures, can it not be tiled? The bathroom can not be without tiles, if not tiled, it is easy for the walls to be soaked with water, easy to rot and crack. When doing toilet waterproofing, it is difficult to paste tiles to do waterproof coatings, waterproof coatings are used for waterproofing, tiles are difficult to decorate, tiles are not strong, and quality problems are prone to occur, although the waterproof layer is pasted with tiles, there are many uncertain factors, but choose the auxiliary materials suitable for the waterproof layer above the wall tiles, the quality of the sticker.

The first process of home installation, first of all, is to change the water and electricity, reinstall the water and electricity, make waterproof paint in the bathroom, when doing waterproof coating, you can do the leveling method, the next is to do waterproof coating, the waterproof coating on the three walls is smooth, dry shrinkage, you can paste the wall tile construction, can you paste tiles on the waterproof layer? The answer I gave is yes, the two materials are suitable for the ceramic tiles attached to the waterproof layer, and the adhesive on the back of the ceramic tiles is to apply glue, and the following is to undertake the reader's.

Ceramic tile adhesive: friends who have been decorated know that ceramic tile adhesive is a barrel latex liquid, which has high requirements for the roughness of the wall. Before pasting the wall tiles, brush the waterproofing layer twice"wall solid"It is mainly used for the pasting of ceramic tiles and waterproof layers, which can effectively prevent the hollow drum from falling off.

The process of pasting ceramic tiles.

The adhesive of the ceramic tile needs to be treated by blister two hours before use, the moisture on the ceramic tile is fully absorbed, the reverse side of the release agent is wiped clean, there is no moisture after drying, and the adhesive is evenly pasted on the back of the ceramic tile with a roller or soft brush. In order to ensure the quality of pasting, the ceramic tiles are placed in a cool and ventilated place indoors, and the latex on the back is gradually transparent, and then you can paste it on the wall.

Ceramic brick adhesive is a mixed mortar powder, different from the traditional cement mortar, cement mortar needs to be matched with a certain number of tile stickers during construction, ceramic brick adhesive contains quartz sand, commonly known as"Medium sand"After screening, washing, drying and other processes, high-quality cement and other auxiliary materials are added, and they are processed by mechanical stirring. Ceramic tile adhesive only needs to add an appropriate amount of water, stir evenly can be used for the construction of pasting ceramic tiles, indoor and outdoor can be used, can replace the traditional cement mortar, mainly used for pasting difficult ceramic tiles.

The bathroom is not waterproofed, what are the treatment methods after pasting the tiles.

Ideas to solve the problem] Through the above analysis of the determinants of water leakage in the bathroom, we will find that the reason why the leakage toilet will leak depends on two aspects. The first aspect is that the waterproofing of the bathroom is not done well; The second aspect is that the bathroom tile gaps are not properly handled. So, we can start to solve these problems.

Solution] The solution recommended by the individual is to deal with the gaps in the bathroom tiles. What we need to do is to ensure that the gaps in the bathroom tiles are tight, so that water does not penetrate down through the gaps. In this way, the leakage of the bathroom is fundamentally solved.

Of course, what we can only do is this protection, then the other protection is the waterproofing of the bathroom that we can't solve. The first method can use the most common beauty joint agent at this stage to seam these tiles. The key to control here is that the tile should not be cracked after the seam is opened.

The second method is to use a waterproof adhesive that is used to repair the cracks in the restroom. This type of glue is sold in many places, and it is very simple to operate. After cleaning the gaps, you can directly brush these glues.

In the traditional sense, the bathroom cannot be waterproofed after tiling. But from the perspective of modern material science, it is possible to apply film on the outside of the tile and redo the waterproofing.

The bathroom has been tiled, and there is no way to do waterproofing! Only when it was found that the bathroom was leaking again, as a last resort, it could only be planed, re-waterproofed, and re-tiled.

After the bathroom is tiled, it can no longer be waterproofed, and there is no point in you doing it again, and. It's also not aesthetically ple Unless you do waterproofing, is it necessary to stick to the wall and sink the ship?

First of all, use plastic bags to block the drain of the floor drain, then mix the gel-type waterproof material with water, and finally pour the prepared waterproof material on the ground and let it stand for about three hours; In this way, the paint will automatically flow into the cracks or unevenness to fill in the waterproofing layer after curing.

No, the waterproof layer is under the tiles, and I really help you look forward to it

Yes, use special waterproof leakage repair materials to make tile joints or pour them under the tiles to achieve the purpose of waterproofing.

Under normal circumstances, after the hydropower renovation is completed, the ground garbage will be cleaned up, and the waterproofing can begin; When brushing waterproof, we should also pay attention to the following details: 1. Brush the pipe mouth several times, and the second time must wait for the first time to dry before brushing; 2. After brushing, start the water discharge test, and wait for the results after 48 hours, and there must be no problems in the test before construction.

It's not that it can't be done, but the effect won't be very good, and it's best to do it before laying bricks.

Hello dear! It's a pleasure to serve you. After the bathroom is waterproofed, it can not be tiled, but the waterproof layer must be sold with cement mortar, which must have a certain thickness, otherwise the waterproof layer will be damaged!

Let me share with you the construction of bathroom waterproofing:1with a water repellent agent.

First use waterproofing agent mixed with cement mortar in the kitchen or bathroom base mold and teasing again, after drying, and then use waterproofing agent mixed with cement ash in the first surface layer in the brush, so that the main purpose is to plug the small holes produced after the first drying, and the root of the pipe should be carefully brushed. 2.With the coil, first clean the base layer to make the base dry, and then spread the coil on the ground, and heat the coil with a spray gun, which is the gap bonding between the coil and the coil.

However, the membrane is fragile, and the surface is easy to be broken by the stones when backfilling, resulting in water leakage, and it is not easy to deal with the root of the pipe. 3.Non-woven fabric, which is similar to cloth, after brushing the base layer with cement mortar thinly, it can be directly spread on it.

Note: Regardless of the type of waterproofing of these three, the perimeter should be 300-500 above the ground to prevent water from flowing down the wall to the bottom.

The wall of the bathroom has different situations according to different divisions, and there are generally two situations: if we use the surface layer as the criterion, there will be two situations:The first situation is that the surface of the toilet wall is just plain plastered, which is called plastering wall.

In the second case, it is common to apply waterproof paint.

The wall surface of the bathroom is the area for bathing and the location of the wash basin, which is also the area where water often splashes in our lives. According to the requirements of the specification, it is necessary to brush with a waterproof coating material, so as to prevent water from seeping into the wall during use, resulting in the return of moisture on the wall, and the result is that the wall is soaked and falling off. We have to spend a lot of money to repair the walls, which brings unnecessary trouble to our lives.

You can only apply tiles after the waterproofing is done, but it is also the type of paint that needs to be paid attention to when applying tiles.

For example, the surface of the wall is coated with polyurethane waterproof material, so it is not possible to directly paste the tiles, because it cannot be pasted, so we need to add an additional process that is the brushing treatment of the wall. Brushing can be very effective in solving the direct adhesion between the bottom layer and the tile bond. Nowadays we use tile glue or mortar mixed with cement.

Such adhesive materials must be bonded to the bottom layer to make the tiles more firm. It is also possible to prevent the tiles from emptying and drumming or even falling off.

As long as the brushing strength reaches the standard, you can apply tiles. So what we have to learn is how to judge the strength of brushing, and what kind of strength can be used to paste tiles. Rather than judging by timeliness, different materials have different brushing effects, and when natural tiles are pasted is also different.