The solar energy shows more than 40 degrees, showing why the water is full and the water cannot be r

The possible reasons are as follows:

1. The sensor is faulty, and the displayed water temperature and water level are inaccurate;

2. If the temperature in your area is currently below freezing, and your home's solar energy does not have any anti-freezing measures, the reason is that the water and water pipes are frozen.

Whatever the reason, it is advisable to contact the dealer who sold you the goods as soon as possible to confirm the fault and fix it in time.

If it is the second reason, one of the following two methods can be used to thaw:

1. Blanch it with hot water;

2. Wrap the antifreeze tape around the outdoor water and water pipes, and then turn on the electricity, and it will melt in a few minutes.

It is suggested that the first method is more difficult to operate, and the second method is the most direct and fast.

After thawing, if it is no longer used in winter, the water in the solar energy can be released. If it is to be used normally in winter, corresponding anti-freezing measures must be taken, such as:

1. Add fixed anti-freeze belts to the upper and lower water pipelines of the outdoor part (but it should be noted that the quality and installation of the anti-freeze belt must be passed, otherwise there will be hidden dangers);

2. Increase the insulation layer on the outside of the pipeline;

3. Increase pipeline circulation;

4. Add the emptying device of the water supply and water pipelines.

It is probably caused by a mistake in the sensor on the solar tank.

It should be that the sensor is broken, and there is no water in the solar energy.

Just replace the sensor.

It should be that the sensor is broken, or there is a problem with the meter.

Summary. 1. The water pressure of tap water is too high.

In solar water heaters, the tap water pressure is too high, so we need to reduce the flow of tap water or increase the booster pump. When the tap water pressure is balanced, hot water can flow out. We usually use water heaters very frequently, so we should always pay attention to the water pressure to avoid excessive water pressure.

2. Vacuum tube problem.

Many homes are installed on vacuum tube solar water heaters, which are an important part of absorbing solar heat sources. If the vacuum tube is not cleaned for a long time, the heat absorption capacity will be affected, and there will be no hot water only with cold water.

Vacuum tube solar water heater in the summer sunny day, heat absorption, the temperature rises quickly, if no one at home for a long time without water, so the water tank in a state of high temperature and high pressure for a long time, will make the water tank aging problem, unable to send water. In addition, the vacuum tube is damaged, resulting in insufficient heat generation, which will also cause the solar water heater to have no hot water.

We need to clean the vacuum tube in time. If it is damaged, we should replace it in time. If no one is at home for a long time, a lid should be placed on the vacuum tube to block out the sun.

A little water on the solar energy shows that it is full, but in fact there is not much water in it, what is the reason for this?

1. The tap water pressure is too highIn the solar water heater, the tap water pressure is too high, which will cause the hot water to not flow out, and we need to reduce the flow of tap water or increase the booster pump. When the tap water pressure is balanced, hot water can flow out. We usually use water heaters very frequently, so we should always pay attention to the water pressure to avoid excessive water pressure.

2. Vacuum tube problemMany families are installed on vacuum tube solar water heaters, and vacuum tube is an important part of absorbing solar heat source. If the vacuum tube is not cleaned for a long time, the heat absorption capacity will be affected, and there will be no hot water only with cold water. Vacuum tube solar water heater in the summer sunny day, heat absorption, the temperature rises quickly, if no one at home for a long time without water, so the water tank in a state of high temperature and high pressure for a long time, will make the water tank aging problem, unable to send water.

In addition, the vacuum tube is damaged, resulting in insufficient heat generation, which will also cause the solar water heater to have no hot water. We need to clean the vacuum tube in time. If it is damaged, we should replace it in time.

If no one is at home for a long time, a lid should be placed on the vacuum tube to block out the sun.

3. One of the reasons why solar water heaters cannot produce hot water is the problem of tap water. When installing a solar water heater, there are many water pipes, and if the cold water flows out, there may be a phenomenon of water stringing. This phenomenon requires the installation of a separate valve and the closure of the valve to prevent the flow of heat and cold.

4. The influence of the automatic auxiliary water tank The float valve in the automatic auxiliary water tank is not closed tightly or malfunctions, which will lead to more cold water, the water temperature drops, and the flow out is not hot water. Solving this problem requires the replacement of the float valve and related components. 5. Leaking pipes, valves or joints and their parts are generally outdoors, exposed to sunlight and wind, easy to damage, and should be maintained and replaced in time if there is a problem.

Failure Cause Analysis:

1. The outlet pipe is blocked, resulting in no water release.

2. The display error is caused by the instrument failure.

3. The installation of the water level probe is not in place, resulting in the display error.

4. The display error is caused by damage to the water level probe or broken line, short circuit, etc.

Solution: 1. Dredge the outlet pipe.

2. Replace the instrument.

3. Reinstall the water level probe.

4. Replace the water level probe and adjust the line.

Emergency solution to the need for hot water: It can be made up directly from the exhaust hole at the top of the water tank, and the time is recommended to be 1 hour before sunrise or after sunset, and the water replenishment can be stopped when the water overflows from the side or top exhaust hole. After the solar water heater fails, it is recommended to contact the buyer at that time as soon as possible and arrange for someone to come to the door for repair.

What happens when the solar water display is full and then there is no water a few minutes later? 1. First confirm whether the solar energy is on the water normally, if there is no water for a long time, the water itself will evaporate. 2. Confirm whether you will put a little water from the solar energy every day, and there is no water, so that the solar water will also be unconsciously emitted.

3. The pipeline is frozen and blocked, and the water from the solar energy cannot be released, so it needs to be thawed with heat tracing or hot water. 4. If the solar energy or vacuum pipe or pipeline leaks, and the water in the tank runs out, the customer service staff can only be asked to repair it.