Why does the washing machine always drain water when it is taken off?

It should be related to water level control. The water level control switch of the washing machine is composed of an air intake nozzle, a pressure chamber, a return spring and a mechanical adjustment screw.

Sogou asked. Disassemble the rear cover, check the air intake in order, the plastic pipe behind is the air pressure intake pipe, this plastic hose is very important, it and the water level control switch should be in a quasi-sealed state, through the change of air pressure in the pipe, push the action of the switch so that the pressure after the water level reaches the start state. Carefully inspect the plastic pipe, find that the joint is ruptured and in a loose state, cut off the rupture, and connect it with a circlip.

Turn on the power supply and start the test machine, and solve the problem of normal operation and start of the washing machine.

If the attack is always delayed and the water is released, it may be that you have set it wrong, you can reset the dehydration function, and it will not.

1. The washing machine is not placed smoothly, no matter whether the ground is flat or not, the washing machine should be placed vertically with the horizontal plane, and the four feet must be placed firmly;

2. Leakage of balance liquid at the upper part of the washing machine bucket;

3. The length of the four booms is inconsistent or the spring elasticity is inconsistent;

4. Open the lid when washing, put the clothes evenly around the bucket before dehydration, and then close the cover.

If you feel that there is a problem with the washing machine, I suggest that you find after-sales personnel to come to the door for testing.

The washing machine always takes off the circle and releases water, maybe it is not the clothes that are not put flat, or the reason why the washing machine is out of order, you can consult the maintenance person.

If this happens to the washing machine all the time, it should be that there is a problem with the rubber ring inside, and if it is something else, there may be a problem with the circuit board.

This may be due to the fact that the performance has been damaged for a long time, and most of the turntables in him have failed, so you can adjust it.

The washing machine always takes off the circle and discharges the water, maybe the time you set is too short, you can set it for a longer time.

The washing machine is dehydrated by draining the dirty water from the washed clothes, and after the water is drained, it is ready for the next spin drying. Like the Haier no-clean washing machine I bought at home. Fully automatic washing machines are like this, as long as you make an appointment for the program, the clothes will be automatically cleaned, or it can be fully automatic

There may be a problem with the setting of the washing machine, you can reset the spinning time mode and length.

Hello, the power supply is cut off first if the washing machine fails. Then see if the belt is loose.

Summary. Hello dear, I'm glad to answer for you, the washing machine is always dehydrated and halfway down and starts to release water? A:

The washing machine is halfway off and automatically discharges the water, which is a mess of the function, and it is necessary to reset it on the line1If there is a serious imbalance in the laundry at the start of the spin, the safety switch will be directly hit when the spinning bucket is started and the washing machine will stop working. 2.

If the dehydration is not particularly serious when the dehydration starts, the unbalance of the clothes is not particularly serious, and the dehydration bucket (including the dehydration outer bucket) will swing and collide with the safety switch due to the action of centrifugal force, at this time, the washing machine will automatically carry out the self-balancing procedure, that is, stop the dehydration, and turn to water injection (automatic water intake) - wave wheel swing (balance clothes) - drainage - dehydration again. If the laundry dehydration balance requirement is not met, the washing machine will automatically perform a self-balancing program several times, then beep to inform and shut down. 3.

For fully automatic washing machines, the solution is to reduce the number of dehydrated laundry washed at a time.

Hello dear, I'm glad to answer for you, the washing machine is always dehydrated and halfway down and starts to release water? Answer: The washing machine is halfway off and automatically discharges water, which is a mess of the function, and it is necessary to reset it on the line 1

If there is a serious imbalance in the laundry at the start of the spin, the safety switch will be directly hit when the spinning bucket is started and the washing machine will stop working. 2.If the dehydration is not particularly serious when the dehydration starts, the unbalance of the clothes is not particularly serious, and the dehydration bucket (including the dehydration outer bucket) will swing and collide with the safety switch due to the action of centrifugal force, at this time, the washing machine will automatically carry out the self-balancing procedure, that is, stop the dehydration, and turn to water injection (automatic water intake) - wave wheel swing (balance clothes) - drainage - dehydration again.

If the laundry dehydration balance requirement is not met, the washing machine will automatically perform a self-balancing program several times, then beep to inform and shut down. 3.For fully automatic washing machines, the solution is to reduce the number of dehydrated laundry washed at a time.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

1. When the washing machine is dehydrated, the clothes are particularly unbalanced. 2. In the process of high-speed rotation of the dehydration bucket, the dehydration bucket (including the dehydration outer barrel) will swing and collide with the safety switch under the action of centrifugal force, and the washing machine will automatically carry out the self-balancing program, and then stop the dehydration and transfer to water injection. If the laundry balance requirement is not met, the washing machine automatically performs several self-balancing procedures, then beeps to inform and shuts down.

3. After the service life of the washing machine is long, the elasticity of the hanging spring of the washing machine spinning off the bucket changes, resulting in the balance of the power of the four hanging springs. Suggested treatment: 1. Reduce the amount of dehydrated clothes at one time.

2. Suspend the washing machine, open the cover, untie the winding clothes by hand and place the clothes flat, and then this will not happen again. 3. If the power of the four hanging springs is balanced, the suspension springs need to be replaced. 4. Special attention should be paid to the fact that it is normal for the automatic washing machine to suddenly jump to rinse when dehydrating, this is set by the program to be like this, when the clothes in the dehydration bucket are placed unevenly, the shaking strength is too large, and the program will jump directly to the water to find the balance again.

In general, this is most common in over-cylinder washing machines.

There is still water in the washing machine after washing the clothes because some models of automatic washing machines are designed with a water retention function, see if you have chosen this program. If the clothes are dry, they will be fine, as is generally the case with fully automatic washing machines, where the water is enclosed in order to keep the bucket balanced when the clothes are dried. In addition, if the water is automatically infilled, it may be a problem with the water level sensor.

There may be debris in the drain valve and corrugated hose, which is known to cause water leakage, and the following is the solution:

1. Use a screwdriver to open the back panel of the washing machine.

2. Carefully observe the internal drainage system of the washing machine.

3. Understand the drainage method of the washing machine.

4. Understand the structure of the drain valve. The drain valve is composed of a valve body and a valve core, and relies on the sealing of the valve core and the valve body to control whether the water is drained or stored.

5. After understanding the drainage method and drainage principle of the washing machine, let's start the operation. First, remove the drain bellows hose.

6. Disassemble the drain valve core, and carefully clean the drain valve core and the internal granular and flocculent matter (such as: artificial jewelry, cotton silk, buttons, etc.).

8. After the repair of Huiding is completed, assemble the back panel of the washing machine and complete it.

According to the manual, the drainage pipe needs to be hung 10cm high

Summary. If the water level sensor is damaged, when the water in the washing machine reaches the water level, the system cannot correctly sense the water level, which will cause the washing machine to be flooded all the time. At this point, the washing machine should display F1, indicating that the water level sensor is faulty.

The water level switch is faulty, if there is a problem with the water level switch, it can not be closed normally, when the water level is reached, the system will control the water level switch to stop the water intake, if the water level does not stop, it may be a problem with the water level switch, it is recommended to replace the water level switch.

No matter what kind of situation you need to repair, it is best to find after-sales personnel in time for maintenance, the general washing machine warranty for 1 year, the main parts warranty for 3 years, do not disassemble it yourself.

1.If the water level sensor is damaged, when the water in the washing machine reaches the water level, the system cannot correctly sense the water level, which will cause the washing machine to be flooded all the time. At this point, the washing machine should display F1, indicating that the water level sensor is faulty.

2.The water level switch is faulty, if there is a problem with the water level switch, it can not be closed normally, when the water level is reached, the system will control the water level switch to stop the water intake, if the water level does not stop, it may be a problem with the water level switch, it is recommended to replace the water level switch. 3.

No matter what kind of situation you need to repair, it is best to find after-sales personnel in time for maintenance, the general washing machine warranty for 1 year, the main parts warranty for 3 years, do not disassemble it yourself.

On the instructions of the drum washing machine, there will be requirements for the installation of drain pipes. Moreover, on the back of the washing machine, there will be drain pipe bayonets, some of which can be pulled out, and some of which are fixed.

Since the drum washing machine drains water, it needs to pass through a drain pump, which is not originally sealed.

That's why there are detailed legends in the manual.

The drain pipe of the drum washing machine must be placed in an inverted U-shape, and the highest point is about 60cm from the ground.

If it is placed horizontally, there will be a phenomenon of water entering and draining from the upper side.

Explain that the washing machine is drained, if the end of the drain is too low, this situation will occur, the only way is to put the end of the drain too high.

If the pattern is normal, it is caused by a poor seal of the drain valve, damage or a faulty traction motor.

The drain valve is stuck and the closure is not tight.

It is a mechanical failure, so hurry up and find a technician to check it.

When washing in a fully automatic washing machine, the wave wheel rotates, while the spinning bucket should not rotate. If the dewatering bucket also rotates, first carefully observe and see the direction of rotation of the dewatering bucket, and then overhaul them separately. There are two kinds of noisy situations with the dehydration bucket, one is that the dehydration bucket follows in the clockwise direction; The second is to follow the counterclockwise direction of the dehydration bucket.

Troubleshooting: 1. The specific reasons and treatment methods for the clockwise rotation of the dehydration bucket are:

1) The brake belt is loosened, so that the braking torque of the brake belt on the dehydration shaft is reduced, as long as the brake belt is reinstalled. (2) The brake belt is seriously worn or damaged. The position of the pawl can be adjusted appropriately by rotating the adjusting screw to increase the braking torque of the brake belt on the dehydration shaft, and the brake belt should be replaced in serious cases.

2. The specific causes and treatment methods of the dehydration bucket following the rotation in the counterclockwise direction are: (1) The torsion spring of the clutch falls off and breaks or the torsion spring and the dehydration shaft are too loose and slip, so that the torsion spring loses its anti-reverse function. Just reassemble it.