How to quickly clean up the sticky logo on the plate

1. Use soap and a little ammonia and turpentine to mix liquid, which can remove a lot of dirt and make the glass surface more shiny (this article is applicable to ceramic tiles, ceramics, glass, etc.).

2. The optical store found that the clerk handled the trademark on the lens: glue it with wide scotch tape, and then tear off the tape to take away the trademark. There is no trace left, 3, wipe it off with a little sodium water, or use paint thinner

4. You can use a hair dryer to dry, and then you can scrape it lightly 5. Wipe it with a cotton swab dipped in nail polish remover.

6. Wipe the wind oil essence.

7. Use a special detergent or sneaker detergent to wipe it.

8. Use the 4B eraser for drawing to be very soft, and you can erase it with the Korean eraser.

9. If the traces that have been left for a long time have hardened, you can use a hot towel to soften it before wiping it.

Tear off the remaining label paper first, which means that no white paper can be left on it. And then you must feel that piece sticky. Then rub vigorously with an eraser.

When you rub the glue together, it doesn't feel good, use paper to wipe off the large pieces of glue, clean up the eraser and then continue wiping. This is the best way to go. I've tried and failed.

If it's stainless steel, just put it on the stove and burn the other side of the label.

Heat with an electric hair dryer and can be easily torn.

This has been tried many times, you have to believe it, and it's very simple.

Vinegar at home can be cleaned

Add stainless steel wire with dish soap.

The trademark glue on the plate can be removed with alcohol, wind oil essence or hand cream. We can tear off a layer of paper on the surface of the plate label, apply alcohol or wind oil, etc., and then rub the surface with our hands to make it fully soaked in the self-adhesive, and finally wipe it off with a cloth to remove.

The glue that is generally used to stick to the plate is a polymer compound in the field of chemistry. Alcohol, gasoline or nail polish diluents are all solvents, and these cavities can dissolve polymer compounds.

Use a hair dryer to blow the hot air on the trademark on the basin, and you can gently tear it off for about 2 minutes, and you can completely tear off the label glue.

The surfactant has good wetting, penetration and dissolution ability, and can quickly penetrate between the self-adhesive and the surface of the object, so as to achieve the purpose of removal.

There are several ways to remove the mark from the plate:

1. Use a hot blow dryer to slightly warm the stupid boy, that is, it can be removed with a notice;

2. Soak in hot water, and after soaking, it can also be easily removed;

3. If the sticking is not too dense, the operation is slower, and it can generally be removed directly;

4. A few drops of edible oil can be easily removed after soaking;

5. If it has been torn off, but there is still self-adhesive, you can wipe it with alcohol and rub it off by hand.

The strong adhesive used on the label, to put it bluntly, is also an organic resin, organic matter and water are incompatible, so it can not be washed off with water, it is difficult to brush off with a wire brush, with wine, vinegar, dish soap, washing powder, soap, boiling water can not be washed off, since it is an organic resin, it must be washed with organic solvents. It is very easy to wash off with strong solvents such as ethyl ester and butyl ester, but this thing is usually not available to people.

In fact, there is another commonly used organic substance around us, that is, dish soap. Didn't you just say that the dish soap doesn't come off? You may have tried, but you can't wash off the glue with dish soap.

But if you don't use water, pour the dish soap directly on top of the glue, and then use a wire brush to brush it, and it will be easily brushed off, clean and very smooth.

It turns out that the dish soap is generally a high-grade alkyl sulfonate + trace surfactant, the high-grade alkyl part is organic and miscible with adhesive, while the sulfonate part is inorganic, so it can be soluble in water; When you dilute the water, the alkyl content is very low, and it is not compatible with the adhesive, so you can't wash off the glue; When no water is added, the alkyl content is sufficient to be compatible with the adhesive, so the glue can be easily washed off.

Give it a try. Very effective.