How to disassemble the Zhongbang four flush lighter? The correct way to inflate a windproof lighter

1.Open the upper cover of the machine to the maximum angle, hold the lower cover of the zippo with one hand, hold the windbreak wall with the other hand, and forcefully pull out the inner tank outward. Turn the liner upside down and unscrew the screws at the bottom of the liner with a taper or coin.

2.After unscrewing the screws, remove the screws, flint springs, and thimbles, replace them with new flints, and put them back in their original condition.

3.Finally, the inner tank is placed into the shell, so that the work of replacing the flint is completed.

Precautions: If you experience a sudden drop in the ignition rate, or if you can observe a significantly smaller number of sparks, it is necessary to consider whether the flint needs to be replaced.

01 If the continuous burning time exceeds the specified time (30 minutes), whether it is used continuously for more than 30 minutes (60 minutes).

10 Abnormal combustion (only a fault indication) Confirm the combustion status and check whether the exhaust heat exchanger is blocked.

11 Poor ignition at the beginning Poor ignition, the main solenoid valve is closed, the ignition device is not ignited, the gas solenoid valve, the induction needle, the grounding wire of the electric controller is not in good contact, and the temperature relay is not good.

12 Flame-out safety device action Flame-out mid-way, combustion status confirmation, gas solenoid valve, temperature relay, flame-out safety device, poor contact of the grounding wire of the electric controller, etc.

14 Operation of the overheating prevention device The operation of the overheating prevention device (disconnection of the temperature fuse) and whether the connector is in poor contact.

1. Drain the air in the lighter first, and press the air inlet and return port at the bottom of the lighter with a screwdriver or other tool.

2. The valve that adjusts the size of the flame can not be closed, nor does it need to be opened to the maximum, the lighter is inverted and the inflator is shaken a few times, and the inflator is pressed hard a few times, and it is generally filled in six seconds (it is recommended to use more than 5 yuan of gas).

3. The quality of the gas affects the ignition rate of the lighter, and many people say that the lighter is broken, but it is actually those two dollars a bottle of gas to blame.

1. The windproof lighter uses a higher gas injection speed, which can form a lower pressure at the appropriate part of the airflow channel of the lighter, so as to "suck" more air in, and fully mix it with the gas of the lighter, react violently and burn, and the high temperature formed by the flame makes the gas expand more and increase the pressure, so that the flame is sprayed out at a higher speed.

2. So it is not easy to extinguish. If the fire is extinguished, the hot metal grille will instantly ignite the fire again.

To put it simply, increase the airflow injection to provide sufficient combustible gas. Increasing heat accumulation, providing an ambient temperature at which the gas burns continuously, this is done through that disc filament (at the spout).

3. Some people say that why the flame color of the windproof lighter is different from the ordinary one? The secret lies in the material of the flame filament. Everyone who has studied chemistry should know that the flame color produced by the burning of certain metals or their compounds in a colorless flame is different.

For example, the flame color of sodium is pale yellow, the flame color of potassium is purple, and the flame color of copper is green.

In the liquid filling method, the mouth of the inflatable tank is facing downwards and the inflator is pressed forcefully. This way it can be topped up. Do not gas tank mouth up, this gas filling method, not suitable for fire engines.

Before inflating, drain the air in the lighter 1 >

Out, with a screwdriver or other tools Press the air intake of the bottom plate of the lighter DAO machine Press a few times to right, 2 > adjust the size of the flame valve can not be closed and do not need to open to the maximum Lighter upside down The inflator is shaken a few times to aim at the inflator and press hard A few times It is generally full in six seconds (it is recommended to use Baicheng lighter gas or gas for more than 5 yuan), the quality of the gas affects the ignition rate of the lighter, many people say that the lighter is broken In fact, it is those two dollars a bottle of gas and then blame,** Search Baicheng Gas, Zhongbang Lighter Origin: Wenzhou, Zhejiang Zhongbang Smoking Appliance Image Spokesperson: Lv Liangwei Domestic good electronic gas lighter Support domestic Support Zhongbang!

I'll answer your questions in response, and some of them are not what you asked.

du windproof lighter.

zhi Before buying, it is best to confirm whether there is a dust cover under the DAO, and it is best not to buy it if you do not have the right to dust cover! Our normal smokers just put the cigarette and the lighter in a pocket, and there is some dust in the corner of the pocket, and the dust of the lighter without a lid is easy to get into the conical vent in the ignition port, and as long as the vent is blocked, the windproof effect of the lighter is basically lost. After disassembling the lighter, you have to use something like a toothpick or tweezers to remove dust or debris.

When dismantling, pay attention: the periphery of the conical air outlet is a circle-shaped ceramic product (the ceramic can withstand high temperatures), if the circle of ceramics is opened or jumped, your lighter will be reimbursed! ~~

Can be inflated.

Lighters, bai look at the following will inevitably have an inflatable mouth. Go to the store to buy a lighter DAO inflatable canister, use the inflatable head of the inflatable gas canister to aim at the inflator nozzle and push it, and the gas of the lighter will be filled.

If it is a disposable lighter without an inflator nozzle, it cannot be inflated unless it is modified to install an inflator nozzle.

If you can't charge it yourself, you can ask the seller to help charge it at that time. Here are the steps to inflate::

Let's first identify inflatable lighters, which can be inflated, usually have a small hole under it, and the edge of the hole is metallic. Ordinary lighters don't have holes here, I only have a symbol, in fact, they can't be flushed.

Hold the lighter in your left hand with the ignition end of the lighter facing upwards, flipping your wrist to allow you to see directly into the hole under the lighter.

Hold the gas tank in your right hand, open the red lid of the gas tank, and shake it before using it.

Insert the top of the gas tank, protruding from the head of a small tube, into the small hole at the tail of the lighter.

Then apply pressure to the tail of the lighter, just pay attention to the moderate force, not too much.

At this time, you can hear the sound of gas, and if there is a gas spill, you will clearly feel that the gas is spilling in the hand holding the lighter, and there is a cold feeling.

It will take about a few seconds to be able to inflate, if you obviously feel that the gas overflow means that it can no longer be inflated, at this time relax the pressure of the gas tank, and directly separate it, this operation should be fast, avoid rushing into the gas, run out of the lighter.

Are you loud, this kind of lighter has to be marked on the cigarette butt like a windshield wiper before it can be lit.

Dot matrix printers, laser printers or inkjet printers? If the words are not very obvious when printing, you need to check the needle type to see if the ribbon should be changed, the laser Wu Blind Hunger to see if it is time to change the toner cartridge, and the inkjet to see if the ink in the cartridge is insufficient. If it is a paper jam, after the printer is powered off, Shenqin, just disassemble the printer and take out the paper.

It can also be that the cavity return energy is not installed well when the drive is not installed.

You see if there is still no power, charge if there is no power, and if you are sure that there is electricity, it will definitely be broken, find after-sales service, repair it yourself, and it is estimated that it will not be repaired.

You see if there is still no power, charge if there is no power, and if you are sure that there is electricity, it will definitely be broken, find after-sales service, repair it yourself, and it is estimated that it will not be repaired.