How is the light size display of the old laser cutting machine connected to the wire?

The protective lens inside the laser head of the laser cutting machine is checked once a day. When the collimator or focusing lens needs to be disassembled, record the disassembly process, pay special attention to the installation direction of the lens, and do not install it incorrectly;

2.Before turning on the power of the water cooler, the water level of the water cooler should be checked, and it is strictly forbidden to turn on the water cooler when there is no water or the water level is too low, so as not to cause damage to the water cooling equipment. It is strictly forbidden to squeeze and step on the inlet and outlet pipes of the water cooler to keep the waterway unblocked;

3.The operator of the laser cutting machine or the personnel who approach the laser during the use of the laser should wear appropriate laser protective goggles, and wear protective clothing, and there must be good indoor lighting in the area where the protective glasses are worn to ensure the smooth operation of the operator;

4.When using gas cylinders, avoid crushing wires, water pipes and air pipes to avoid electricity leakage, water leakage and air leakage. The use and transportation of gas cylinders shall comply with the gas cylinder supervision regulations. It is forbidden to expose the cylinder to the sun or near a heat source. When opening the bottle valve, the operator must stand on the side of the bottle mouth;

The old model almost appeared with his cutting machine, and the size showed that we could still connect the wire, and if we connected the wire, we could still debug it according to our own use.

How is the light size display of the laser cutting machine connected to the wire? This has to ask, search the Internet, the old laser cutting machine, the correct way to debug the grounding wire.

Hello, if this machine is connected to this wire, you must find a special maintenance master to help connect it, which is safer.

If you want to connect the wires, you must find an electrician, so that the wires can be connected safely.

Why don't you send it out? How do we understand telecommunications? Hope this is an opportunity of what assists the control method?

The size of the laser cutter light shows that the wire is actually connected to one side of the contour of the light.

In this case, you should find the relevant person or take a look at the instructions to operate.

The size of the old laser cutter shows that you can follow his tips to connect the wires.

Generally, it is not the problem of the wire, but the aging of the laser element and the need to replace it with a new one.

This is a professional problem, and it is necessary to contact the manufacturer's after-sales service for consultation and processing.

The wiring method of the laser cutting machine, you can wire it according to its instruction manual, there will be a detailed wiring diagram on it, and you can operate it according to the instructions.

This you can play the after-sales service of the laser cutting machine**, let them tell you how to connect the wire, after all, they are more professional.

If you want to know how to connect the wire, you can search and query the laser cutting machine in the web page, and you can find the relevant operation method by connecting the wire keyword.

Parkson Laser is a high-tech enterprise specializing in the research and development, production and sales of large and medium-power laser equipment, integrating laser, precision machinery, numerical control, software development and modern management.

After years of continuous innovation and development, Parkson Laser has become a large-scale enterprise, and is a group and international company composed of Guangzhou Parkson Electronic Technology, Hong Kong Parkson Electronic Technology, Foshan Hui Parkson Technology and Taizhi Technology. The company has an area of 100,000 square meters of modern standard workshops, more than 200 sets of precision machining equipment and more than 500 energetic employees in Foshan, Guangzhou, with an annual production capacity of 3,000 sets.

The company's product categories cover more than 60 models such as laser cutting, laser welding, laser marking, laser engraving, etc. It has 150 technicians and 100 technical patents. The product has stable performance, high precision and good quality. Integrated production line, sufficient supply and timely guarantee.

Parkson laser service tenet: all for customers, for all customers.

We are committed to building a world brand of industrial-grade laser cutting machines and providing laser intelligent equipment solutions for global users.

Welcome friends who are interested in updating laser equipment to contact 400-008-8807

The size of the old laser cutting machine shows that if you want to connect the wire, you can look at the circuit diagram and connect it according to the circuit diagram.

The fiber laser cutting machine does not produce light for the following reasons:

1. Check whether the power supply of the fiber laser cutting machine is in good contact to ensure that the power supply is in good contact 2. Check whether the circulating waterway of the fiber laser gas cutting machine chiller is blocked, and the waterway should be kept unobstructed. The special dual-temperature chiller is specially designed for fiber lasers and has triple filtration; There are two refrigerations, one for the laser and the other for the lenses.

There are about three problems, one of which is that the height of the work table is inconsistent, which can be adjusted. Second, the optical path is biased, and the four limit points can be adjusted to the same point, and third, the life of the laser tube is weak, because after the laser is reflected by the reflective lens, if the light intensity of the laser tube is not enough, there will be such a large light difference. For details, please consult Beijing Yiming Laser.

Is the light weak? How long has your laser tube been used, try to replace it, and it is also possible that the light is biased.

Upstairs is the right solution, laser cut mesh.

Laserarea professional technical team, laser brand after-sales strong joining.

laserarea laser problematic, go laser cutting mesh.

Daikin Laser has the answer for you:

1. Whether the laser power switch (green switch) of the machine is turned on.

2. Check whether the chiller is open, and check whether the light signal, control signal and water protection signal of the chiller are normal.

3. Check whether the light output of the laser tube is normal; Low light (purple) is abnormal, normal is pink, whether the water flow of the laser tube is normal.

4. Check whether the laser optical path of the machine is normal, press the light to see if the laser tube is bright, bright and the laser head is not bright, then there is a problem with the optical path.

5. Check whether the button panel light is normal, check whether the machine operation panel, power is correct, or whether the computer software parameters are correct.

6. The laser power supply fan does not rotate and does not convert the power supply.

7. Check whether the light is coming out directly from the laser power supply signal, and if the light is out, the laser tube and the laser power supply are normal.

8 Whether the voltage is lower than 200V

2) During the operation, the laser machine suddenly does not shine as follows

1. Check whether the chiller is alarmed.

a. Alarm, connect the water inlet and outlet behind the water tank with a water pipe, and the water tank is energized to see if it is alarmed. If you call the police, the tank is broken. If it is not alarmed, it is that the water channel of the laser pipe is not smooth, check whether the water pipe is bent or pressed by something, and whether the water in the tank is debris (replace the pure water in the tank).

b. Do not alarm, check whether the laser power supply fan is rotating. The laser power supply fan turns, and the foot of the laser power supply is shorted with the wire, whether the laser tube is out of light, and the light is out, the wire on the motion control card is loose, or the motion control card is broken (replace the board). There is no light, and the laser power supply is broken.

In rare cases, the laser tube is broken) (check whether there is ignition at the high-voltage end of the laser tube, and the ignition is easy to burn out the electronic components of the laser power supply and the board), the laser power supply fan does not rotate, and test the 220V port of the laser power supply with a multimeter to see if there is electricity. There is electricity, and the laser power supply is bad. (repair or replacement of power supply); If there is no power, check the laser power switch, wiring.

Fault 1: The size of the cut figure is not accurate.

Solution: Adjust the software file settings, the pulse equivalent in the workbench, generally 6400 pulses per 32 movements, according to different machines, 32 can be increased and decreased finely adjusted to achieve the best cutting accuracy.

Fault 2: There is a stuck sound when the machine is moving.

Solution: Check whether the bearing beads in the synchronous wheel are broken and need to be replaced, if the camera is used to automatically cut, the laser engraving machine recognizes the card in the process, and it is possible that the camera data signal line is broken in the middle and needs to be replaced.

Fault 3: The machine does not move or the size of the cut out of the figure changes irregularly Solution: Check whether the driver and the motor are powered on (the power on hand can not be pushed), the drive is green when it works normally, if the track of the motor can be pushed after power-on, the motor shaft may be broken, and the motor needs to be replaced.

Call ** to find the after-sales service of the equipment manufacturer. Explain the problem.

Call ** to find the after-sales service of the equipment manufacturer.

First, the machine is not transported

Check whether the power switch of the laser cutting machine is turned on;

Check whether the power cord is connected to the power plug and whether it is loose;

Check whether the panel is powered on.

Second, the pump does not work normally:

Check whether the circulating system of the fiber laser cutting machine is blocked;

Check the liquid level of the entire system to ensure that the pump can receive the liquid;

Check that the pump motor is operational.

3. No refrigeration or insufficient refrigeration:

Check if the voltage is too low or too high;

Check to see if too much heat is diverted to the cooling fluid of the fiber laser cutting machine, resulting in exceeding the cooling capacity of the refrigeration system.

Fourth, the pump suction power is insufficient

Check if the fiber laser cutting machine connection pipe is restricted;

Whether the voltage is too low or the fluid viscosity is too high.

Five: the light is not out when it is turned on.

Check the laser power switch of the machine;

Check that the chiller is turned on;

Check whether the light from the laser tube is normal;

Check whether the laser optical path is normal;

Check whether the laser power supply fan is rotating;

1: Check whether the water is circulating normally, let the water circulate normally, if the water protection is broken, you can use it for short water protection.

2: point presetting, see if the ammeter swings, if not, use a multimeter to measure whether the laser power supply has 220V intake, if there is no light, the power supply may fail, and it needs to be replaced.

3: You can also test whether the water protection is bad on the GND ground wire and P water protection short joint on the power supply, and check the maximum output power by shorting +5V and AIIN.

4: If the program does not come out, the connecting card can be used to measure whether there is a DC voltage of more than 3V between the 15 (h) or 16 (l) angles and 14 angles with a multimeter and a multimeter to measure whether there is a voltage above DC 3V, if there is, the card is normal, and there is no possibility that the signal of the card is problematic.

5: There is a sound inside the laser power supply, generally because the power connector is in poor contact, re-soldering or connecting, and then blowing the dust in the power supply.

The main reasons for the laser cutting machine are as follows:

1.If you don't have a light, the laser is bad or the control card is bad, and sometimes it is very common to turn off the machine on vacation and turn it on, and there is no laser.

2.There is a problem with the laser companion software.

3.It's possible that the control board is loose.

4.The temperature of the laser tube is too high to protect it, and there is no loose cable, or the board is broken5If the correction file is missing or the dongle is not plugged in, the laser tube will not shine.

The light does not shine when it is turned on.

Check the laser power switch of the machine;

Check that the chiller is turned on;

Check whether the light from the laser tube is normal;

Check whether the laser optical path is normal;

Check whether the laser power supply fan is rotating;

Landlord, you must have a problem with the machine. If the machine suddenly has no laser, you can be sure that the optical path is good. Then turn on and restart to take a look, and then press the point to shoot out the laser to see if there is, if not, then you observe whether the laser tube is flashing, if there is, the laser tube power is not enough or the focusing lens is broken.

==Three lasers, thank you!!

Reasons and solutions for laser cutting machine not to shine 1: Check whether the water is circulating normally, let the water circulate normally, if the water protection is broken, it can be used for short-term water protection; 2: point presetting, see if the ammeter swings, if not, use a multimeter to measure whether the laser power supply has 220V intake, if there is no light, the power supply may fail, and it needs to be replaced. 3：

You can also test whether the water protection is bad by the GND ground wire and P water protection short section on the power supply, and check the maximum output power by shorting +5V and AIIN. 4: If the program does not come out, the connecting card can be used to measure whether there is a DC voltage of more than 3V between the 15 (h) or 16 (l) angles and 14 angles with a multimeter and a multimeter to measure whether there is a voltage above DC 3V, if there is, the card is normal, and there is no possibility that the signal of the card is problematic. 5: There is a sound inside the laser power supply, generally because the power connector is in poor contact, re-soldering or connecting, and then blowing the dust in the power supply.

The first is to check whether the laser power switch of the machine is turned on; Also pay attention to whether the chiller is turned on, and check whether the light signal, control signal and water protection signal of the chiller are normal;

Then carefully observe whether there are accessories that are not operating normally, resulting in no light. Check whether the light from the laser tube is normal; Low light is abnormal, normal is pink; whether the water flow rate of the laser tube is normal; Whether the laser optical path is normal, check whether the laser tube is bright according to the light, and if the laser head is bright and the laser head is not bright, there is a problem with the optical path; Check whether the button panel light is normal, check whether the machine operation panel, whether the power is correct, or whether the computer software parameters are correct;

The most important thing is whether there is a fault in the laser power supply, and when checking, it is generally necessary to check whether the laser power supply fan rotates, if it does not rotate, it means that the laser power supply fails and needs to replace the power supply; Or check whether the light is out directly from the laser power supply signal, and the laser tube and laser power supply are normal; If there is still no light, it means that the laser power supply is faulty, and the power supply needs to be replaced;

Finally, there is one of the most easily overlooked problems, which is the working environment of the equipment, check whether the voltage is lower than 200V. The voltage is too low to work properly.