tp link td 8810 ADSL plus TP LINK TL R402M router setup

I've seen your structure diagram, because 8810 is a modem with routing function, if 8810 turns on the routing function and then connects to the router WAN port, it will definitely not be able to dial up the Internet.

You can reset the 8810, and then directly connect to the WAN port of the router and dial through the router.

At the same time, the computer gateway needs to be the same as the gateway of the router, but not the same as the IP address of the cat.

1.My router is the same as yours. Your router needs to be reset. It is to use a small pin to insert the small hole in the back when the power is on.

2.Then fill in your account password in the router settings.

3.You may be insinuating that the port is intended to use BT. It's not so much trouble.

Just fill in the DZM option with the specified IP address of your machine. This way, your machine is not inside the firewall of routing. It became the extranet.

But you have to do a good job of protection.

4.Turn on the pnup option.

5.There's nothing else to set up with the router. Because it is not necessary for the average user.

6.If you're using a router, you don't need to dial up. Because your route is equivalent to a computer connected to the network.

7.You'll need a one-meter-long mesh cable with two crystal heads. All your machines are connected to the router first, and then connected to your TP-Link TD 8810 ADSL by the WAN port of the router through a one-meter line, and then to the ** cable.

8.If you're using it alone, there's no need to use a router.

Am I not satisfied?

The cat does not need to be set, and there is no need to map the port in the router, you only need to enter the router pppoe item, set the Internet account and password to the router, and the shared computers are connected to the router, and any computer can be directly connected to the Internet after it is turned on.

I've encountered your problem, in fact, if you want to set up the Internet, you don't need to map the port. Because your TP-Link TD 8810 ADSL comes with routing itself. Your tp-link tl-r402m is a router and a hub.

When two pieces of hardware with routing functions are used at the same time, one of the routers can only be used as a hub, otherwise it will conflict and cannot connect to the Internet. That is the reason why you said that you can't connect to the Internet when connected to the WAN port, and you can connect to the Internet when you connect to the LAN port.

It's just the reason, so let's add 200 points!

ADSL does not need to be set (you can restore ADSL to factory design), to set up only the settings of the router, the route with PPPoE connection, just select this option, add your username and password to it, you don't need port mapping, your many machines can share the Internet, you look at my link and everything will be.

First, go to the router's settings screen.

Enter according to the IP indicated on the instruction manual.

And then it's good to go.

According to my information, your 8810 also has a routing function, then it is equivalent to the cascade of two routers, you are using a straight line (that is, the kind you used to connect 8810 and the computer), the cascade should use a crossover line (commonly known as a dual-machine interconnection line), you change a crossover line to try, the problem should be here.

At the same time I also had to map ports 80 and 9991 on the router

Your IP?

It is not enough to connect the WAN port of the router to the LAN port of ADSL.

Wanted to ask what you want to insinuate the port for? If you just want multiple computers to access the Internet through your router, you can enter your Internet ID and password and then activate the router.

As much as I wanted those two hundred, I couldn't do anything about it.

TP-Link TD-89402 is a wireless router. Like any other router, it is used to set up a wireless network and provide wireless network for tablets, laptops, and smartphones.

How to install a wireless router:

1. The router is plugged in, and the network cable is plugged into the WAN port of the road;

2. Connect the computer and the router with another network cable (plug one end into any LAN port of the router, and plug the other end into the computer);

3. After opening the computer browser, enter the IP of the router in the address bar (there is one in the manual, press enter;

4. Enter the username and password of the Withered Orange router, generally the initial username and password are admin (can be found in the manual).

5. Click "Setup Wizard" and click "Next";

6. Select PPPoE (ADSL Virtual Dialing) and click Next.

7. Enter the Internet access and Internet password (that is, the network username and password written in the contract of the network and operator), and click "Next";

8. Select "WPA-PSK WPA2-PSK", enter the password and click "Next" (this password is the WiFi password);

9. After the router is set up, click "Finish".

<> set the key simplification method as follows: Manuscript Zheng pants.

The first and the book excite to open the browser program first,Enter it in the browser address bar,Generally, a window will pop up,And the password is admin。

Then perform the pose training dial-up socks, select ADSL, and enter your broadband and password.

Then set the wireless password, encryption method, etc., and then save the settings.

TP-Link TL-WR841N 300M Wireless Router Add Wireless Signal Method:

Step 1: Take a used beer can and wash it.

Step 2: Pull out the tab.

Step 3: Remove the entire bottom by making a circumferential cut along the bottom of the tank.

Step 5: Draw a line vertically on the reverse side of the left part and cut the iron sheet along the line.

Step 6: Iron sheet, so that the aluminum can retains part attached to the base, pass the antenna through the mouth of the can, and fix the bottom of the can with landing.

The Wi-Fi signal amplifier is complete, as shown below:

The signal strength cannot be set, and the signal will automatically be stronger if it is closer to the partition wall.

This is a cat + routing machine that supports ADSL broadband for ** line access. There is a ** cable connection entrance, and four network cable ports are connected to the computer.

If you have telecom broadband and IPTV at home, this machine is good. The second LAN port is specially designed for IPTV access.

TP-Link TD-89402 Enhanced Specifications.

Basic parametersDevice type: External ADSL supported protocol: ANSI, ITU interface type: RJ45, RJ11

Transmission performance: maximum uplink rate: 1Mbps Maximum downlink rate: 24Mbps (ADSL2+), 8Mbps (ADSL).

Other parameters Operating temperature: 0 40 Storage temperature: -40 70

Product FeaturesProduct Features 1: Support ADSL broadband routing function, built-in 4 100M Ethernet ports with enhanced lightning protection design, support IP QoS flow control function through PSTN 4000V lightning test standard, reasonably allocate Internet bandwidth to provide 1 RJ11 interface and 4 100M Ethernet (LAN) interfaces.