The water pipes in my home are very loud, what is the reason?

There are two main reasons why the sewer pipes in the home need to be wrapped, one is to be soundproof, and the other is to make it look more beautiful. Here are a few ways to wrap the sewer pipe.

First of all, there are two less common ones, the first is to make a frame of a wooden keel next to the water pipe, and then install a gusset of PVC on its surface. The other is to nail a layer of wood on the surface of the keel frame, and then add aluminum-plastic panels. However, in this case, the wooden keel is more likely to deform due to moisture.

Nowadays, it is common to use soundproof cotton to wrap the sewer pipe, then put a keel on its surface, and finally add tiles. Because the sound insulation effect of tiles is not obvious, it is necessary to use sound insulation cotton. This method does not take up space, but it will be relatively high.

Another way is to build a wall, the sound insulation effect of this method is still very good, and there is no need to pack sound insulation cotton, ** cheap, but the space occupied is relatively large.

This is the effect of the bathroom

This phenomenon is physically known as water hammer and often produces sounds. This situation is caused by a counterattack caused by the sudden cessation of the flow of water in the water line when it flows. For example, when the water flows, the valve of the waterway is suddenly closed, and the water hammer phenomenon is easy to occur, which is due to the fact that when the water flows in the pipeline, when it passes through a certain valve, the valve is relatively loose.

Air enters the water pipe, it may be that there has been a water outage before, the water pipe enters the air, turn on the faucet to the maximum, and drain the air and water together for a while, and the sound gradually decreases.

After the renovation of the new house of the house, there was a chirping sound in the water pipe, what is going on, did the workers steal the materials, and the water and electricity were not done? For this purpose, I went to ask the workers, and the workers bluntly shouted their grievances and patiently. The cry of the water pipes is not a failure to save water.

There may be several reasons. The sound of the water pipe caused by the hammer phenomenon, that is, the water flow is large when the water is used, and the turbulent water flow causes the water pipe to resonate. If that's the reason, the workaround is simple. When using the faucet, you can reduce it a little, reduce the flow of water or simply replace the faucet!

Water pipes chirp due to water leakage, and water leakage occurs in the water. The amount of water leakage is small, and there will be a whistle-like sound when using water, and the general leakage is due to the angle valve of the faucet.

and loose internal components such as the inlet valve, in which case the workaround is simple. Just replace the angle valve or water inlet valve and it will be solved. Air is mixed in the water pipe to produce a chirp, the water consumption is too large, the diameter of the pipe is too small, a small amount of air is precipitated from the water, and the water pipe makes a chirping sound.

The workaround for this situation is simple. First check the faucet, the faucet is not well sealed, and it will make a crying sound when it is opened. If you can tighten the faucet, repair it, or add your own water pipe, you can solve it.

If you can't find a reason for tweeting in the above situations, you can go next door and ask him if there is a water pipe at home to post Weibo. If anything, the houses are now lived in in small districts, and the water pipes are shared. It will be more troublesome to encounter this situation.

The cooperation between real estate and tap water can be solved. If the water pipes in your home are also chirping, please think about whether it is due to one of the above reasons. Only by finding the problem can it be solved quickly and effectively.

Do you know? > because there is an imbalance in the pressure of the gas in the water pipes. The quickest fix is to twist the faucet and put in the banji and water. Install an automatic exhaust valve at the highest point of each riser.

can be solved, the current high-rise building.

The water supply system needs to be fitted with an exhaust valve. The connection strength is high, the welding gas protection of the on-site weld is difficult to meet the standard, and the welding is easy to rust, which can directly reduce the life of the pipeline. The quality of installation is highly dependent on the welder's technology, and the quality is difficult to stabilize.

When connecting, the end face of the pipe cut should be perpendicular to the pipe shaft, the burrs inside and outside the cut should be cleaned, the depth to be inserted into the front of the copper pipe should be marked with a marker pen, and then the pipe should be inserted into the pipe fitting forcefully. Reduce installation risk, suitable for a variety of installation environments, reusable, environmentally friendly and energy-saving leakage, shockproof, thermal expansion, shrink-proof, safe and durable.

It may be that the pipes of the water pipes are not installed very firmly, and the vibration caused by the excessive water pressure will cause a humming sound.

It may be that the pipe installation is not firm, because the water pressure in the water pipe is too large, so it will make a sound, and you need to close the water valve a little less, and the sound will disappear.

It is very likely that the water has stopped, or there will be a pipe vibration when the water is about to come, so there will be some buzzing sound.

Probably because of the water hammer, which is the sound that occurs if the sluice gates are suddenly closed while it is flowing inside.

This condition may be a phenomenon known in physics as water hammer, which often produces sounds. The reason for this phenomenon is the counterattack caused by the sudden cessation of the flow of water in the water pipeline.

For example, when the water flows, the valve of the waterway is suddenly closed, and the phenomenon of water hammer is likely to occur, which is due to the fact that when the water flows in the pipe, when it passes through a certain valve, the valve is relatively loose.

Because the general tap water pressure is about three floors, the main reason is that the general residents have a water tank upstairs, and at the same time connected to the tap water, when people use less water at night, the tap water pressure is too high, and it is unstable, high and low, resulting in water friction on the water pipe wall, and often produces sound.

Water pipe noise elimination method:

If it is in the bathroom, there are basically suspended ceilings, and it may also be the commonly used integrated ceiling. The integrated ceiling can be opened and the opening of the pipe above the top can be filled with soundproofing material, so that the sound of running water can be eliminated.

If the pipe is not installed firmly, there is gas in the pipe, causing the water pipe to hum or whistle, and there is a sound due to the vibration caused by the excessive water pressure in the water pipe. Close the inlet valve a little lower and the sound will disappear.

If the inside of the faucet is not well sealed (for example, there is a problem with the rubber ring inside), because the seal is not tight, the water will flow out from the gap, causing vibration and then noise. This situation requires the faucet to be replaced.

Answer pro 1, if it is because the pipeline installation is not firm, due to the excessive water pressure in the water pipe caused by vibration and sound, at this time it is recommended that the user close the water inlet valve smaller, then at this time the sound will naturally disappear. 2. If there is gas in the pipeline, it will cause the water pipe to hum or howl, and only the user needs to discharge the air at this time. 3. Poor internal sealing of the faucet will also cause such a situation, because the sealing is not tight, so the water outflow is rushed out from the gap, causing vibration, and then producing sound, at this time, it is recommended that the user replace the faucet.

1. If there is air in the water pipe, the exhaust valve can be installed, and the water can be discharged normally after installation. Due to many conditions, there is air in the water pipes, and in some places the air cannot be discharged, resulting in the obstruction of the water flow. Therefore, as long as the exhaust valve is installed in some places, the water can be discharged normally.

2. The exhaust valve is installed at the pump outlet or in the water supply and distribution pipeline to remove a large amount of air gathered in the pipe. In order to improve the efficiency of the pipeline and the pump, and once there is negative pressure in the pipe, the valve quickly inhales the outside air to protect the pipeline from damage caused by negative pressure.

It's simple, but when the water pressure is insufficient, the water flow decreases, and some openings open water at the same time or when there is no water, air will enter.

The solution is to change the diameter of your own water pipe, which was originally six points and now changes to four points, and if it is a supervisor, you can increase the water pump.

This should happen when there is a lot of current.

It shouldn't be when the water is slow.

If there is a valve, you can open the valve and expel the air.

If there is no valve, it can be said that the water flow is open to the maximum, and it may also come out.

1. When this happens, we can adjust the water flow of the faucet and adjust it to the appropriate angle, so that the faucet will not beep.

2. If there is air in the pipe, then we must first exhaust all the air inside, and then there will be no beep.

Your home should be an old-fashioned galvanized pipe, and it is an open pipe, and there is no way to eliminate this phenomenon. When the water is boiled, there is a vibration and sound for a few seconds, and then it is fine. There is no problem with the faucet and the valve, but because the old pipe is made of thick white glue, there will be some water seeping out and air in.

The only way to solve the problem is to change the water pipe, and changing to a PPR hot melt pipe will not have this phenomenon. However, this phenomenon should not affect your life.

There is air in the water pipe, there is a roaring sound in the treatment method is very simple, release the water for a long time, discharge the gas out, and the straight road can be without a roar.

This is because the water has stopped, and you have just released the water, the pressure of the water is too great, you can open the water pipe, let the water pipe exhaust, the gas is discharged, and after a while, it will be fine, and there will be no more roar.

Set up a trap to drain the air

Change the diameter of your own water pipe, which was originally six points, but now change it to four points, and if it is a supervisor, you can add a water pump.

When the water pressure is insufficient, the flow of water decreases, and some openings open water at the same time or when there is no water, air will enter.

Although the proportion of water pipes in decoration is not very large, it plays a very important role. You must know that it affects our water safety in the future, and after long-term use, we often encounter some problems. In general, when too much air enters a water pipe, it can cause the pipe to expand.

In this case, there is air pressure. At this time, it is difficult to balance the air pressure outside the tube. When air enters, it creates uneven air pressure, and when it is resisted, it will hum, especially high-rise water pipes.

It can be solved by installing an exhaust valve on the top of the riser. When purchasing, you need to check whether the inner diameter is uniform. During installation, it is difficult to dock the two interfaces.

You can smell the water pipes for odors. In general, there is no odor. But like some products of poor quality, some toxic plastics may be mixed in during the production process, so it smells good.

Whether the color of the water pipe looks normal, whether it has glossiness, whether the outer wall is marked with pressure and specifications, etc. According to the regulations, all water pipes should be marked with these. The thickness of the hot and cold pipes is different.

Some people think that the same kind of hot and cold pipes can be used. This is not right. Different pipes should be used.

First of all, you must know that cold water pipes cannot be used as hot water pipes. At the time of purchase, there was a red line on the hot water pipe. If there is no red line, it is a cold water pipe.

When buying, it is best to buy products of the same brand, because their interface is better connected when connected. It may be that there is air in the water pipe connected to the faucet, and because the air floats upwards and the water flows downward, the collision of the two causes the water to make a sound when it passes through. A blind pipe can be installed at the highest point of the water pipe and then the air can be exhausted from the water pipe at regular intervals.

It may be that the water flow is too large, so the amount of water coming out is too large, causing a sound. The faucet can be turned down appropriately to prevent waste and eliminate hum. It may be that the faucet has been used for a long time, resulting in the aging of the internal structure.

Just get a new faucet. There is abnormal noise in the water pipeline, the faucet valve core is aging, the closure is not tight, and the valve core produces self-excited oscillation under the action of water pressure. This can easily happen at night when the water pressure is high.

Aging faucets need to be replaced, or the water pressure can be lowered appropriately. There will be a lot of noise when the water is discharged, which is a physical phenomenon caused by the quality of the faucet. When the faucet components do not fit well together, when the drain is not fully opened, a common vibration between the water flow and the components will occur.

This sound is originally small, but the water pipe only acts as a loudspeaker, and it is very noisy. In this case, you just need to replace the faucet. The pipe installation is not firm, and the water pressure of the water pipe is too large to cause vibration, and there is a sound.

If the inlet valve is closed, the sound will disappear. There is air in the pipes, which causes the water pipes to buzz or scream. The air is expelled.

The inside of the faucet is not well sealed. Because the seal is not tight, water flows out of the gap, causing vibrations and then noise.

I think that if there is a buzzing sound in the water pipes in the house, then it is likely that our water pipes have been damaged to a certain extent, and there are several parts of the pipes that are broken.

Answer: Generally, the water pipe enters the air, there is too much air, and then the gas enters the water pipe to expand the pipe, which is bound to have air pressure, and the external air pressure in the pipe is not uniform, that is, the uneven air pressure generated by the outside air entering the pipe, and there will be a buzzing sound when it is resisted. It is the water supply pipes in high-rise buildings that are most likely to hum. Standing at each root.

Ask <>

Rent a house. The landlord is very old. Nobody does plumbing.

I don't know. The 2nd floor is ringing. Nothing to do.

Is it okay to change the faucet.

Question: If you don't turn on the water pipe, it will ring. The sewer pipe does not ring.