How do I cancel my table tennis trainer order?

<> Li Bai was about to go on a boat, and suddenly heard that he was stepping on the shore.

How to cancel the table tennis trainer order, this we can withdraw.

I once watched a show that is common sense, if you want to remove the trademark, you can use plastic wrap to stick the ping pong ball for a period of time, and the trademark will fall off naturally and leave no traces, it should be okay.

Just blow it on with a hair dryer for a while.

1. Treatment of glue residues on the bottom plate. If it is not cleaned, the next time the rubber is peeled, the rubber will be damaged, and the bottom plate will fall wood chips, and it is particularly important to remove the glue in time for Stika and butterfly boards (these two types of rackets are easy to drop wood chips from various models). 1. The general glue residue can be rubbed directly by hand until the bottom plate is smooth.

2. Glue stains on the bottom plate that have existed for a long time. Brush a layer of glue on the bottom plate first, and the glue is best to choose a slow-drying type, such as Haifu ordinary glue, and after the glue is basically dry, rub the rubber surface of the waste rubber (not a sponge) vigorously, and the effect is very obvious. The focus of the action is that the glue can not be too dry or too wet when rubbing the glue, and the glue liquid disappears to start it, and the effect is not good if it is late.

The principle of degluing in this method is: using the characteristics of glue miscibility, so that the new glue dissolves the old glue. The reason why you can't use quick-drying glue is that the glue is too dry and dissolves into one with the glue, so you can't remove the glue, if you can't achieve the desired effect at one time, you can wait for the bottom plate to dry and then repeat the above process.

I have used this method to remove several glue stains from the finished product more than ten years ago.

Second, the treatment of glue stains on the rubber (set of glue).

a, with glue brush directly with the hand rubbing, glue should also choose the slow dry type, hands-on time second, the advantage of this method is that the damage to the rubber is small, the disadvantage is that the hand is very tired and painful;

b. For some older rubber, you can brush the glue once, rub it with the rubber surface of the waste rubber, pay attention not to use too hard, otherwise it is easy to damage the sponge, and the direction of rubbing is best from the position of the handle and then down, because this position is not cut and is not easy to break. The advantage of this method is that it is fast and labor-saving, and the disadvantage is that there is some damage to the sponge. It is emphasized that the above method A imported rubber sleeve should be used with caution, and method B is only applicable to domestic rubber sleeve, and imported rubber sleeve is prohibited.

The imported rubber is too brittle and will break when touched).

Personally, I recommend that if you rub the skin too handy, I use small tape, so I directly use smooth tape to rub the glue instead of fingers.

If the glue sticks to the surface of the rubber, the area is small. You can try to wipe it gently with gasoline, and you can't use it too much, as more will affect the elasticity of the rubber and sponge. If there is a lot of glue, you can't use the method just now, you can only replace the rubber.

Do not use gasoline in small quantities!!

Alas! After you get the rubber off! Don't stick anymore!

1. Start with a rag! Get the water in the sky! Wipe it clean vigorously! I scrape on the bat with a blade!

2. Wait for him to do it! Then glue it to the bat! Rubber too! I repeat it exactly twice!

3. Glue it on again! Press down it with a wooden stick! Roll over every section!

4. This is a big announcement!!

If there are other questions or parts that are not clear enough, please continue to ask. Thanks for adopting!

Pour the gasoline or thinner into a small porcelain bowl and put the brush in the small porcelain bowl containing the gasoline or thinner

There are two glues corresponding to different methods:

1. The brush coated with inorganic glue (water-based glue) can be directly cleaned with clean water, rinsed under tap water and rubbed the bristles, and then dried after washing.

2. The brush coated with oil-based organic glue (solvent-based glue) can be soaked in a container of appropriate size with solvent thinners such as gasoline, xylene, and rosin for a while, and then rub the bristles, and the glue on the bristles is cleaned and the solvent on the bristles is dried, and then the bristles are washed with tap water by rubbing the bristles with dish soap, washing powder, etc., and the water is dried to dry. Solvent diluents are flammable, so be careful to prevent fire.

Just rub it with medical gauze dipped in some medical alcohol.

Theoretically, alcohol and organic solvents can remove the handwriting of the signature pen on it. But a lot of table tennis balls are celluloid, this kind of table tennis balls are two halves together, but this material may dissolve in alcohol, you can see if your table tennis ball is this kind of this, if it is, try it with acetone. If not, be more careful, if it's a seamless table tennis ball, the material of this table tennis ball is unknown, you can try it.

1. Blanch it in boiling water;

2. After the scalding, use a small brush to brush it off.

The way to deal with the residual glue on the bottom plate of the table tennis ball is to scrape it with a knife or sandpaper (it must be very finely marked), but the former may damage the clapper board, and the latter cannot be completely cleaned. The recommended method is to scrape off part of the coating with a knife to the point where it is possible to lift off a portion of the film.

Use a damp soft cloth to vigorously rub the surface of the glued board. This method is effective in removing residue from the panels and does not damage the panels at all. Note that the racket will be very wet and should not be applied to the new rubber immediately, but should be completely dried before applying new glue.

It is recommended to rub with a table tennis ball.

The landlord buys a one-star double happiness to rub.

It is better to use a ball to remove the glue on the rubber sponge.

Happy holiday netizens' method solved a big problem for me, I just tried it and it really worked, cleaned up half, and sent a picture to take a look.

There are special dissolving agents and degumming agents for degumming.

HSL200409 - Director Level 8 says: Heat it with a hair dryer first, and then find a piece of waste anti-glue to rub it off. It's also a way to do it.

Heat it with a hair dryer first, and then find a piece of waste adhesive to rub it off.

It works well with discarded rubber, but you can also try using thinner.

Remove glue solution or remove with water, rub.

It's okay, it's gone if you don't fight for a while, but it will grow back if you fight again.

It will slowly disappear, but the table tennis ball may need to be played less.

I have it on my hand too.

I also play table tennis.

I'm in my second year of junior high school. There is no such thing as this.

Does it have any impact?

It's okay, don't care, it'll grow if you go, but too often just scrape.