The bathroom tile joints are so dirty, all of them are moldy, what should I do?

Buy some mold remover online, and after touching it, dispose of the moldy place, and then buy a beauty sewing agent to fill it.

Scrub with toilet cleaner, if the effect is not good, you can use a cone to remove it, and then fill it with beauty sewing agent or caulk.

Because there is water in the bathroom for a long time, it may accumulate some garbage in the gaps of the tiles, and you can use a brush to brush these gaps.

Control 100 mold removal gel, used when studying in South Korea, South Korea is close to the Han River and the sea, the weather is particularly humid, especially in the rainy season, the clothes will grow hair.

It can be soaked in white vinegar and then brushed.

1. First use a small shovel to clean up the tile gaps, remove the debris inside, and then apply the prepared beauty grout along the tile gaps.

2. You can first wipe the black and moldy place, and then fill the toilet paper with 84 water, spread it in the blackened place, and remove it after the toilet paper is dry.

3. When using it, you can dilute the hydrochloric acid and brush it back and forth on the black gap several times with a brush, and the effect is very good. However, due to the corrosive and pungent taste of hydrochloric acid, we should take protective measures when using it.

4. The humidity of the bathroom is usually relatively large, and the requirements for the tiles are waterproof, anti-slip and wear-resistant. Cleaning the tiles with soap and a little ammonia and turpentine can make them shinier.

You can try to sew it with beauty.

When there is mildew in the tile joints at home, we first need to consider what causes this situation, and the common reasons include: dampness, poor ventilation, blind water in the corners and other places, which affects ventilation, etc. In terms of processing, we can take the following measures:

1.Clean tile joints: Use a toothbrush or brush dipped in white vinegar to gently scrub the tile joints to clean the mold.

2.Disinfection tile joints: You can use professional disinfectants on the market or homemade disinfectant water (water + alcohol + a small amount of white vinegar), pour it in the tile joints, wait for 5 minutes and then rinse it with water.

3.Moisture-proof ventilation: Keep the room dry and ventilated, which can be adjusted by using dehumidifier grinding dust culture, opening windows for ventilation, etc.

4.Tile joint filling: If the situation is more serious, you can consider refilling the tile joints and repainting the cement mortar to block mold from entering the gaps.

In short, we must find out the mildew problem of tile joints at home and take corresponding measures to deal with it in time to keep the room clean and dry, which is conducive to our physical and mental health.

The reasons for the moldy porcelain bricks on the bathroom wall can be called Honghui can have the following points:

The waterproof layer of the bathroom is damaged, causing water vapor to spread through the wall, resulting in moisture and mildew on the wall.

There are cracks in the exterior wall of the bathroom, which causes water seepage into the wall and mold on the wall tiles.

There is a leak in the water pipes in the bathroom and answer, which causes the walls to be damp and moldy.

There is a faucet on the inner wall of the bathroom, and the water droplets stay on the wall for a long time, causing the wall to be damp and moldy.

It is recommended to check the waterproof layer, wall cracks, water pipe leakage, etc. in the bathroom, and take corresponding measures to repair it in time. At the same time, you can try to remove mold with a mold remover. If the situation is severe, consider redecorating the restroom.

There are many stains in the cracks of the tile, teach you the trick of cleaning, and clean as new in one minute.

What kind of sewing agent is better?

1.Buy products with high volume. The fullness directly affects the beauty of the later stage, and the shrinkage and collapse of the product with high fullness after curing is very small, so as to ensure the aesthetics of the product.

2.It depends on the scrub resistance of the product. The higher the scrub resistance, the longer the service life. A good product has high strength and high hardness after curing, and is strong and durable after the protective layer. The protective layer with low hardness is relatively thin and easy to break after a period of use.

3.Convenient construction. There are some on the market that can be used directly with a beauty sewing agent, and there is also a double mixture. It is recommended that you buy a copy for direct use, which is more convenient, and you have to buy it back and mix it again.

Where can such a product be used in home improvement?

1.Mosaic gaps, floor tile gaps, tile gaps.

Dip the EL1300 with a brush and apply it.

Refresh the caulk so that you can plug the mold directly.

Scrape off, dry and refill. If the tile itself is blackened, there is no way.

It's the caulk, you must have used an inferior caulk, refill it, you can get the original one off with a brush, and then make a sewing agent outside, it's okay, the sewing agent is waterproof, so that there will be no mold problem.