Looking at the solid wood floor heating floor is very hot, is it okay?

Floor heating must pay attention to check whether the installation of the pipes of your floor heating and all the water pipes buried under the floor is scientific, followed by choosing the right solid wood floor.

Floor heating wood flooring selection criteria.

1. The floor is dimensionally stable and can withstand temperature changes without damage.

2. No deformation, cracking, small thermal expansion and contraction coefficient.

3. Eco-friendly, no formaldehyde and harmful gas release.

4. Don't be afraid of soaking the floor with water (prevent the floor heating pipe from being damaged, the water from flowing out of the floor from being damaged).

Solid wood flooring vs. laminate flooring.

1. Generally speaking, laminate flooring is more suitable for underfloor heating. Because the standard thickness of the floor heating floor is, the thickness of the composite floor is mostly 6 9mm, of which the laminate floor is mostly 6 8mm, and the three-layer solid wood parquet is 8 9mm, the heat transfer performance is better, and there is a layer of aluminum oxide wear-resistant layer on its surface, which is conducive to the rapid diffusion of heat on the surface.

2. The general thickness of solid wood floor is about 2cm, and the keel should be played when installing, if it is used as a floor heating floor, there is air between the floor and the ground, and the thermal conductivity of air and wood is very low, so that the heat is not easy to be conducted to the surface, which will lead to the waste of heat, the surface temperature is uneven, the temperature difference is obvious, and the composite floor is pressed by high temperature, and the internal moisture content is very small, so the floor will not be deformed due to the loss of moisture. The multi-layer parquet is staggered horizontally and vertically between each layer, and there are dense anti-deformation grooves on the back, which decomposes the stress generated by the heating surface, so the amount of deformation is small.

The solid wood floor heating floor is very good, environmentally friendly and healthy, and the quality is also very good.

However, if you buy solid wood floor heating flooring, you must choose a big brand.

I know that Jiusheng solid wood floor heating floor is very good.

The home is copied floor heating, which will have an impact on the wooden floor.

The ground radiant heating system is mainly based on the ground as the heat dissipation surface, the whole room for low-temperature floor radiant heating, the floor heating room floor material selection from the thermal conductivity considerations, natural stone is the best, followed by ceramic tiles, then composite flooring, and finally wood flooring.

So in the same case, wood flooring has the most thermal insulation and relatively poor heating effect. Sometimes, due to the lack of dryness, the moisture in the solid wood floor is too large, which may cause the floor to warp and bulge when applied to the floor heating room.

No, in fact, the floor heating floor of nature is okay, especially the installation of the steel buckle, and the other will not take a few years to warp, and it will have to be replaced. This one is more stable.

Generally for the majority of decoration owners, if you want to do floor heating, solid wood floor will be our first choice, because I have always heard that solid wood floor is the most suitable floor for floor heating. However, recently, relevant experts have proposed that it is not recommended to apply solid wood flooring when decorating floor heating, and the relevant reasons for this topic have been sorted out for your reference.

1. Is solid wood flooring not suitable for floor heating?

In fact, solid wood flooring is not impossible to do floor heating, it is not recommended to do it.

Reason 1: Because the moisture content of the air solid wood floor is high, it is prone to deformation and other problems, even if the geothermal heat is not used, the maintenance ruler is not properly laid

Reason 2: It is too troublesome to use and maintain, solid wood is a banquet with many advantages but too tired, if the geothermal use of solid wood is even more, heating and cooling need a degree to give the floor an adaptation process In order to look good tired of yourself, I personally feel that it is not worth it

Reason 3: The effect of heat transfer, or more directly the problem of energy consumption, the thermal conductivity of the floor material is arranged in order from large to small: pure wool carpet. The smaller the thermal conductivity, the higher the operating costs to achieve the same heating effect.

Reason 4: Problems with the installation; When the solid wood floor is paved, the keel should be beaten (for the feeling of the feet), and there is air in the middle of the keel, which will reduce the thermal efficiency. In addition, the threat of nailing to the underfloor heating system (both water and electricity) is great, and a special laying process is recommended.

Second, do you know that solid wood floor heating floor?

If netizens confirm that there is no problem with the above problems, then solid wood can also be used for geothermal heating, but there is also a choice for wood. Solid wood geothermal flooring is favored by high-end consumers for its excellent environmental protection.

The requirements for solid wood floor heating are much higher than those of ordinary solid wood flooring. Let's take plumbing as an example: "The water temperature of floor heating generally does not exceed 55 degrees, and when used for a long time, the water temperature is controlled between 35 degrees and 45 degrees, which can make the temperature of the room rise to about 22 degrees."

Since the floor heating floor has to withstand a temperature difference of 30 to 50 degrees Celsius, the technical indicators such as heat resistance, shrinkage performance, and wood density of the floor are much higher than those of ordinary flooring. Pure solid wood geothermal floor refers to the solid wood floor that can be directly used for underfloor heating (geothermal) environment on the basis of not changing the natural properties of solid wood flooring.

The use environment of geothermal floor is complex, especially in the northern region, the ground has to withstand various moisture in the non-heating season, and the ground temperature rises suddenly during heating, and the floor must bear the double change of "temperature" and "humidity". Therefore, the geothermal floor must be made of material with good stability. Teak is recognized as the most stable wood in the world, and is recognized as the best solid wood geothermal flooring in and outside the industry, but at a higher price point.

Good environmental protection is the indicator that consumers are most concerned about, after all, it is related to health and safety of use.

With people's health requirements for an environmentally friendly living environment, pure solid wood geothermal flooring is undoubtedly the best way to solve the essential problem, from the composite geothermal floor that is not environmentally friendly and exceeds the formaldehyde standard, to the quality composite geothermal floor with low formaldehyde emissions, and then to the solid wood geothermal floor that leads the pioneer of healthy life today, it truly provides a guarantee suitable for the physical and mental health requirements of the living environment of the elderly and children.

In general, wood flooring is the most heat-resistant. Among them, the solid wood floor is used for floor heating, and it is necessary to use solid wood floor heating for floor heating, otherwise it will not only block the heat in the later stage, but also bring the consequences of floor warping.

Finally, floor tiles are preferred for underfloor heating.

1. Industry insiders said that under normal circumstances, the geothermal room can be paved with solid wood flooring, but it is not recommended to use it in this way, and it is best to pave laminate flooring and solid wood parquet instead. Because of the beautiful color and comfortable feel of hardwood flooring, many families use it as the first choice for bedroom floor covering.

2. Solid wood flooring is made of natural wood cutting boards, which are processed by special dehydration and degreasing processes to make standard size boards. But during the heating period, the floor needs to withstand a certain amount of heat, when the moisture in the air is absorbed into the wood, the wood will expand, and when the air is relatively dry, the moisture of the wood will run into the air, making the wood dry and shrink. If you use ordinary solid wood flooring, it is easy to crack and shrink joints.

3. In addition, the solid wood floor cannot meet the requirements of geothermal heat in many aspects, and the solid wood floor needs to be keeled to produce a thick air layer, and the wood itself is a poor conductor of heat. Moreover, the fiber structure of wood has the characteristics of moisture absorption, and it is easy to deform when absorbing water and losing water under the change of temperature and humidity. This affects the life of the flooring and is therefore not suitable for use as floor heating, so it is recommended that owners use laminate flooring and parquet flooring.