The screen does not light up after installing Deep Deepin on the computer?

It is recommended to replace the U disk maker, redo the U disk PE, change the system image, and use the freshly made U disk to redo the operating system, preferably with the image of the Akiba system.

1. There is a problem with the graphics card of the host.

Check to see if the graphics card is broken, and see if the host has an alarm sound. If you're using a discrete graphics card, unplug it and plug it into the integrated graphics card to see if the integrated graphics card has a signal.

Solution: Memory problem: First check whether the memory is plugged in tightly, generally after the chassis is moved, the memory may become loose and cause a boot failure.

In addition, it may be that the host has accumulated too much dust and caused a short circuit in the memory, you can blow the dust near the memory slot first, and then use an eraser to wipe the gold finger of the memory module after cleaning it up.

2. There is a problem with the cable of the monitor.

In many cases, the data cable of the display is not plugged in, resulting in the signal not passing, the display is not bright, or the data cable is faulty, which can lead to the signal cannot be transmitted.

Solution: Change to a new display cable.

3. The monitor is broken.

Find a different monitor, switch to this console, and see if there is a display. If you don't have many monitors, you can take a laptop, connect this monitor to the laptop, and then check if it can be displayed.

Workaround: Repair the monitor or replace it with a new one.

4. Power failure.

If the screen is not lit and the computer indicator is responsive, and you can see a faint image with a flashlight, just change the backlight.

If the keyboard light is on, press the numlock or caps toggle key at the top left of the keypad to see if the keyboard indicator responds. If so, pay attention to the sound of the system starting. If the keyboard light is responsive, it means that the system boots up normally, but it just doesn't show up.

Solution: Power on the monitor or the host.

5. Lamp failure.

Replace the lamp with reference to the LCD instruction manual, and it is best to take the LCD to a professional repair shop for maintenance, which is more safe and reliable.

If you replace the LCD backlight by yourself, you should be careful to avoid unnecessary losses.

The domestic system is still not very complete, and it is recommended to reinstall it. The deep system is still very smooth, but there are too few applications, and the installation penetration rate is too low, but I see the hope of the domestic system, and I wish the domestic system and the Microsoft system, the Mac system is as smooth as the ecology, and supports domestic production.

If the brightness is low due to the operating system, we recommend that you change the system image and reinstall the operating system.

1. All solutions 1. Open and click Add New Entry. 2. Click NeGrub 3. Click Install 4. Click Configure Enter the following information in the pop-up notepad program 5. Restart the computer, select the "Neogrub Bootloader" boot option, and select the "Intsall Deepin" option after entering the Neogrub bootloader to boot the system. 6. "Choose to try and install deepin", after which you will be asked to select the installation language, I chose "Chinese Simplified".

Then you enter the deepin trial interface 7, call up the deepin terminal in the trial interface and enter the command sudo umount -l isodevice to cancel the mount of the driver where the disc is located 8. Open the built-in "partitioner" of deepin, select the unallocated space you reserved, click "New" in the upper left corner, and create a new 15G partition (the unallocated space is 25G in total, and this new partition is the mount point of Deepin in the future. ), the format is ext4, without the drive letter 9, double-click "Install deepin" on the desktop"Start the installation. 10. Fill in the username and password 11. Select Expert Mode 12. Pop up the dialog box point OK 13. Select the 15G partition just divided, select the mount point as , and select the "Format" column.

Then create a 2G swap partition on the remaining unallocated space, and finally create the remaining unallocated space as a partition in format ext4 and mount point home. 14. Select the partition where you live, you want to install Deepin on the partition 15, click Install 16, and the system will complete it by itself. Just choose Restart when you're done.

According to the version of the host try a few are feed error terminal command: sudo chmod +w boot grub enter password (password display) car input: sudo gedit boot grub I fifth start item windows modified set default=0set default=4 save close document terminal command:

sudo update-grub pushes the terminal to restart windows in the first position.

Actually, I think linux deepin xcfe desktop environment friends want to play with desktop special effects for help detailed operation steps I should kde official ** upload version of the package specifically how to install it.

Reply 1 Is wubi slow to install? How do I not think? I installed wubi on both the book and the desktop, and it took about 10 minutes to install and configure it and enter the desktop.

It doesn't feel slow to use. I guess the landlord ran into the same problem when I installed it on the book.,After entering the menu, it doesn't move at all.,Only the cursor flashes in the upper left corner.,The screen doesn't move.,The keyboard can't move.。 To restart, you can only press the power button.

If the phenomenon is the same,The landlord replied,I'll post my solution.,Because this problem seems to be encountered by very few people.,I can't find it in a lot of forums.,I solved it by accident in this book.。

Wubi installed Ubuntu, which is twice as slow on my machine as the direct partition and only faster than the virtual machine. From now on, I don't recommend others to use wubi, the experience is too bad, it is better to teach people to use virtual machines.

Reply 10 Your situation is obvious, it is an error when setting the resolution automatically, it is out of standard, and it cannot be displayed. You shouldn't have this problem with wubi.

Reply 7 The problem I have seems to be not much the same as yours.,When I installed it,There was no signal input on the direct monitor.,But the host looks normal.,The hard disk light flashes normally.,It's just that you can't get into the screen no matter how long you wait.。

Reply 4 Oh? What configuration? Why is this happening?

Type help enter to know how to use it.

Use the find command to find the kernel and then init kernel and other commands to boot the reason why this is because grub can't find or wait for the boot menu configuration file is a problem with your installation, one is to check whether grub is set up when you install it, and the other can't boot the kernel in the jfs rfs and other partitions, it's best to put the kernel and grub configuration files in the ext3 partition, just in case.

Let's analyze the specific problem on a case-by-case basis.

First of all, you said that the linux deep system is a mistake in itself.,There's no deep system.,Linux distributions are particularly numerous.,You must have been over the mirror or pirated to call it that.,If it hasn't been able to load, it should be grub not booted up.,The best advice is your own ** official image and then use a U disk to install the system.,My computer has 7 systems and 2 Linux are Ubuntu and Kali Linux.Follow-up questions.

First of all, try to repair the system with a USB flash drive, it really doesn't work, it is recommended that you replace the system image and reinstall the system.

1. Make a U disk PE system on other machines, you can try U Master.

2. The U disk is inserted into this computer, and the boot is set to the U disk to start, and enter the PE system.

3. Open the system repair software on the desktop, automatically or manually repair the C drive, repair the F drive, and close the software. Open the partitioning software, right-click on the hard disk, and rebuild the Master Boot Record MBR.

4. Restart the computer, unplug the USB flash drive, and wait to enter the system.

This situation occurs on the computer due to a system problem, you need to reinstall the system, if it still doesn't work, you need to go to a professional repair shop for inspection and repair.

First of all, partition your hard disk, generally partition out the C drive as the main partition, def as the extended partition, trouble to install the system in the main partition. That's it!

Install Win7 on the VHD virtual hard disk, and put it on any disk without any problem. VHD can also be differential, once the system is broken, you can use differential backup to restore.

In another version, the current depth is not the same as before

In the case of the system, it must be installed on the system disk.

This is a system problem, you can repair the system files through security software, if it can't be solved, then you can only reinstall the system to solve the problem completely, and the installation system is best installed with a system CD or a U disk boot disk.

In the 1 2 3 that interface to choose 2 to see if it is okay?

If the monitor shows a black screen after booting, but the sound of entering the system can be heard, and the mouse pointer is displayed normally, it proves that there is no abnormality between the monitor and the computer host, and the operating system is faulty, which can be solved by the following methods:

Try to press "Ctrl+Alt+del" under the system to bring up the task manager, if it can be called, force the explorer process to end, and then click in the file menu in the upper left corner of the task manager, select "New Job" and re-enter "Rebuild explorer process".

If the above steps do not resolve the issue, you will need to reinstall the operating system.

Are there any other devices that can boot, such as bootable USB flash drives, CD-ROMs, etc.?

I can't find the boot information, fix the boot with PE.