How to remove marks left by moving wooden benches on tiled floors

It depends on the material, floor tiles are floor tiles, which are roughly divided into glazed tiles and full-body tiles, and floors are floors, which are roughly divided into solid wood floors and composite floors. (There are more detailed categories, so I won't go into details.) ）

If it is a floor tile, you need to see what material it is, if the floor tile is a glazed brick The enamel has been crossed out, revealing the traces of gray or gray red, then it is difficult to remove it completely, you can use similar paint or colored caulk to fill the upper layer of stone glue after polishing and polishing, but it can only be faded, and the enamel can not be restored. If the floor tiles are full-body tiles, then you can find a local stone dealer and let their professionals come to your home to polish the floor tiles partially, then the marks will fade.

If it is a floor, then a similar problem generally does not occur with high-quality laminate flooring, which has a layer of aluminum oxide wear-resistant layer, and iron brushes can not scratch it. If it is a solid wood floor, it will be troublesome, if the wooden floor has not been waxed, you can find a professional painter, according to the floor texture after the oil and wax, but the hardness of the paint film will be worse. If your wooden floors have already been waxed, congratulations, they can't be painted, so you're going to use them!

The above are hand-made based on personal experience, and there is no copy and paste. For the sake of my hard work, give me some encouragement.

Tell you a way, you can definitely wipe it off: use nitric acid (those who sell bathroom sanitary ware, one point is enough), cotton swab and gently wipe it, and you can wipe off the traces in a few seconds.

Find someone who does floor polishing and waxing, basically you have to do maintenance once a year, you can't get rid of laundry detergent, you have to use floor wax to get it, but you're really good at laying the floor first and then painting??? Not even a point is given.

A lot ... I can't get it.

Don't be so troublesome, the surface wear-resistant layer of laminate flooring is aluminum oxide, which is also commonly known as "synthetic diamond", and the general thickness is about 40. So, you can gently sand with very fine sand until the black marks are worn off.

There is no need to worry about the floor being worn out during the sanding process, because the regular floors are sandpaper sanded and tested, and the wear-resistant layer has sufficient thickness.

It is recommended that you choose the finest sandpaper for carpentry, as too thick sandpaper will cause visible scratches on the surface.

Ways to remove black marks from the floor:

1. Rust stains: You can soak them in hot water first, and wash them with water after applying acetic acid or oxalic acid solution.

2. Aged rust stains can be mixed with oxalic acid and citric acid (10 oxalic acid and 10 citric acid are each half).

3. If there are few stains, you can also use a cotton swab dipped in water containing 5% acetic acid, and wipe the stain over and over again, and the rust stain will disappear.

Use a metal cleaner and then rub vigorously with a brush.

1. Use an eraser to wipe in little by little along the edge to easily remove marks. But depending on how sticky you are, it may take a different time. If possible, alcohol + eraser works very well.

2. You can take a dry cloth stained with vinegar to cover the entire double-sided tape traces, and wait until the sticky stains of the double-sided tape are completely soaked, and you can easily remove them with a ruler. 3. You can also use heating to soften the adhesive of the double-sided tape: blow it with a hair dryer to soften the adhesive, and when the adhesive of the double-sided tape becomes weaker, it can be easily removed.

If there are still small marks, wipe them off with polish remover that removes nail polish. 4. When clearing, whether you use glossing water or vinegar, you must let these supplies completely soak the double-sided adhesive marks to remove them easily and effectively! 5. Use soap and a little ammonia and turpentine to mix liquid, which can remove a lot of dirt and make the glass surface more shiny (this article is applicable to ceramic tiles, ceramics, glass, etc.).

6. Use viscous transparent glue to repeatedly stick and tear, you can remove some of the surface 7, wipe it off with a little sodium water, or use paint thinner 8, wipe it with a cotton swab dipped in nail polish. 9. Wipe with wind oil essence. 10. Use a special cleaner or sneaker stain remover to wipe.

Dip in cooking oil and rub slowly.

To be more detailed, it is best to drip oil on the towel in advance, let it dry for a period of time, make an "oil towel", and then wipe it. The effect is more pronounced.

Gasoline or go to the auto repair shop to have that rust water, still doesn't work so try bleach powder again, range soak for a few minutes and then use a step brush to brush!

Diluted oxalic acid and toilet cleaners can be tried.

Just wipe it again with an old half-dry towel.

Generally, you can use a dry mop to drag it again after the wet mop has passed, and don't let the water stains dry on their own, so that there will be no traces.

To clean paint marks on tiles, you need to prepare: paper towels, disinfectant.

1. First find the traces of paint on the tiles.

2. Next, spread a paper towel on top of the paint marks of the tile.

3. Then pour an appropriate amount of disinfectant on the paper towel.

4. It is necessary to pay attention to completely soak the disinfectant in the paper towel.

5. Wait until the disinfectant on the paper towel is dry, and then tear off the paper towel.

6. Finally, the paint traces on the tiles are removed.

The latex paint is rubbed with gasoline, and the rest can only be shoveled little by little, which is how I did it.

Wait until it is completely dry and shovel it directly with a shovel.

1. Hydrochloric acid or phosphoric acid solution and water are mixed in a ratio of 1:5 (if the paint is thicker, you can drop some hydrochloric acid or phosphoric acid solution directly on it first).

2.Pour the prepared water on it, sprinkle it with sawn foam, and use a wooden shovel (don't use metal to leave marks, let alone steel wool balls for brushing pots). When shoveling, you can also use a rag dipped in water to wet the paint slurry.

It's okay to use a wooden shovel to make it a little stronger, and pay attention to cleaning up with the shovel. When you're done, you can wipe it a few more times.

Cleaning and maintenance of ceramic tiles:

1. The ordinary dust on the surface of the tile can be cleaned with dish soap, soap, laundry detergent, etc.

2. The wax layer of polished bricks when leaving the factory can be removed with decontamination king.

3. The cement scale, caulk and other dirt remaining on the surface of the tile can be removed with the descaling king.

4. Paints, coatings and other pollutants are dissolved and removed by chemical solvents, such as Tianna water.

5. Black metal scratches, welding marks, etc. can be removed with descaling king.