What is a sweatband and how to use it?

It is made of towel or glue to wrap the ball handle, which can absorb sweat and prevent the ball from slipping and falling out, if the novice uses 2-10 yuan.

A sweatband is a wrapping cloth on the handle of the paddle that needs to be replaced regularly. Here's how to wrap a sweatband:

Step 1 Press the thin end (start end) of the sweatband on the side of the bottom cover of the handle. Generally, the beginning of the sweatband will be attached with a double-sided adhesive sticker. Fix the sweatband as shown below, or in the opposite direction if you are holding it in your left hand.

Step 2 Hold the handle with the fingers of your left hand and rotate it clockwise, while your right hand controls the direction of the bands to align them. The edges of the sweatbands can overlap each other, depending on personal preference, but are usually 2 mm.

Step 3 Wrap the sweatband around the bottom end according to the above method, cut off the excess sweatband at this time, if necessary, you can trim the upper edge of the sweatband according to **.

Step 4 Prepare the tape that comes with it and wrap the end of the sweatband with tape so that it doesn't fall apart.

Everyone should pay attention to the process of winding, and the sweatband should be properly tightened, otherwise it may spread out during the shot. Sweatbands are best at the beginning of stickiness and sweat absorption, and become more and more slippery with the time of use. From a hygienic point of view, bacteria increase over time.

In order to ensure the feeling and hygiene of the shot, change the sweatband regularly. The recommendation is to change it once a week.

1. First take out the sweatband and tear off the film on it.

<>4. When winding, pull the sweatband slightly, and the deformation is about as follows.

5. Then according to this Sun Da angle, then the vertical will start to continue.

6. Finally, after getting the end, glue the sealing glue and it is completed.

1. First take out the sweatband and tear off the film on it.

<>4. When winding, pull the sweatband slightly, and the deformation is about as follows.

5. Then according to this Sun Da angle, then the vertical will start to continue.

6. Finally, after getting the end, glue the sealing glue and it is completed.

1. First take out the sweatband and tear off the film on it.

<>4. When winding, pull the sweatband slightly, and the deformation is about as follows.

5. Then start continuing from this angle.

6. Finally, after getting the end, glue the sealing glue and it is completed.

Step 1: There are two commonly used hand glues, one is adhesive hand glue with film, and the other is dry hand glue without film. If it is an adhesive hand glue, first remove the protective film on the surface of the hand glue, this side of the hand glue is wrapped on the outside and is in contact with the palm, and the other side is wrapped inside and is in contact with the handle.

Step 2: Remove the double-sided tape on the tip of the glue, which is the place where the glue begins, and attach it to the end of the handle.

Step 3: The right hand gently tightens the glue, which is very important, so that the glue surface is slightly deformed, so that the glue surface can be more suitable for the handle and not easy to shift, while the right hand pulls, the left thumb presses the glue surface to prevent rebound, and slowly wraps the hand glue on the handle. Note that it is slightly deformed, not too much deformation!

Step 4: Use scissors to cut a bevel in the hand glue to facilitate sealing.

Step 5: Start sealing, but at this time there is still something missing, and at this time another attachment of the hand glue begins to appear ......It is a sealing strip, similar to an insulating tape.

Step 6: The method of wrapping the sealing strip is similar to that of the hand wrapping glue, pressing on one side and starting to pull on the other side. The rubber surface after pulling off is very thin, and there is almost no unevenness when you touch it.

You can also choose to use a sticky, thin insulating tape, because it is wider than the self-contained sealing glue, it is not easy to loosen, and it is very easy to use.

At this point, it's done, and you don't have to get a specialty store for hand wrapping glue in the future!

Today I will share with you a fishing trick, how to wrap the sweatband of the fishing rod handle! I hope it can help fishing friends.

Sweatbands, also known as hand glue, are wrapped around the handle of badminton rackets and tennis rackets, which have the effect of sweat absorption and anti-slip, so that the grip is more comfortable when playing and the playing experience is better, so what are the types of sweatbands?

1. Grip glue: refers to the grip glue directly wound on the wooden handle of the racket, the main function is to protect the wooden handle of the racket and provide basic functions such as anti-slip and sweat absorption.

2. Outer grip glue: refers to the grip glue wrapped around the outer layer of grip glue, and its main function is to provide players with performance requirements such as anti-slip, sweat absorption, playing feeling, and comfort.

3. Towel grip cloth: refers to the cotton grip glue with high cotton content directly wound on the wooden handle, and its main function is to provide players with comfort and strong water absorption.

The above is an introduction to the types of sweatbands, I hope it will be helpful to friends.

It's just starting from the bottom and wrapping it up one by one, there's nothing to say.