How to wrap the badminton sweatband, how to wrap the sweatbadminton band

How to wrap sweatbands

Step 1

Press the thin end (start end) of the sweatband against the side of the bottom cap of the handle. Generally, the beginning of the sweatband will be attached with a double-sided adhesive sticker. Secure the end of the sweatband at the end of the handle.

Step 2

Hold the handle with the fingers of your left hand and rotate it clockwise (just keep the logo straight), while your right hand controls the direction of the bands so that they align. The edges of the sweatbands can overlap each other, depending on personal preference, but are usually 2 mm. During the winding process, the sweatband should be properly tightened, otherwise it may spread out during the shot.

Step 3

Wrap the band around the band to the bottom as described above, cut off the excess band at this point, and trim the upper edge of the band if needed.

Step 4

Prepare the tape that comes with it (the same little strip you told you not to throw away) and wrap the end of the sweatband around it so that it doesn't fall apart.

Note:

1. The stickiness and sweat absorption of sweatbands are the best at the beginning, and they will become more and more slippery as they increase with the use time.

2. Finally, from the perspective of hygiene, bacteria will increase with the time of use. In order to ensure the feeling and hygiene of the shot, change the sweatband regularly. It is recommended to play the ball 5 times and change it at least.

Wrapping the handle sweatband is an important preparation for badminton, and it will fall apart after a while, which will affect the feeling and comfort of playing. The correct way is:

1. Peel off the protective film on the surface of the hand glue, this side of the hand glue is wrapped on the outside and is in contact with the palm, and the other side is wrapped inside and in contact with the handle.

2. Uncover the double-sided tape on the tip of the hand glue, which is the place where the hand glue begins, and stick it to the end of the handle to fix it.

3. Tighten the hand glue moderately to make the glue surface slightly deformed, which can make the glue surface more suitable for the handle and not easy to shift. At the same time, the thumb of the left hand presses the rubber surface to prevent rebound, and slowly wraps the hand glue on the handle.

4. Wrap the sealing strip, which is similar to the method of wrapping hand glue, press on one side, and start to pull on the other side. The finished rubber surface is very thin, and there is almost no unevenness when you touch it.

It's very simple, first tear off the glue, and then wrap it around and wrap it

Wrap it around the stripe on it, and if it doesn't work, then find a master.

The square sail method of wrapping a badminton racket with a sweatbladder is as follows:1. Prepare sweatbands and rackets.

2. Pull open the beginning of the sweatband search.

3. Glue the sweatband to the side of the bottom cover.

4. Rotate the handle to wrap the sweatband.

5. The edges of each other are overlapped by 2 mm.

6. Subtract excess sweatbands.

7. Subtract the corner of the end of the sweatband.

8. Tape is attached to the end wrap.

9. Complete the winding of the sweatband.

The above is how to wrap a sweatband around a badminton racket.

Badminton is a sport that requires a lot of exercise and physical strength, usually, we will produce a lot of sweat when playing badminton, which will make us feel very uncomfortable, and the winding method of sweatbands is to solve this problem.

Choice of sweatbands.

When buying a sweatband, we should choose a sweatband with a moderate width, comfortable material, and good water absorption, and at the same time pay attention to whether its size is suitable for your head circumference.

Start winding 1Lay the sweatband flat on the table top and fold the ends in half so that the sweatband takes on a shape.

2.Place a sweatband on your head so that both ears and forehead are covered.

3.Wrap the sweatband around your chin and cross it twice over your head.

4.Cross the sweatband twice over the back of the head, then bring the sweatband back to the front of the head, and pinch both sides of the sweatband with both hands to adjust.

Note 1In the process of winding, it is necessary to ensure that the tightness of the sweatband is moderate, too tight or too loose will affect the comfort and roughness during exercise.

2.During competitions or training, sweatbands can easily become damp due to the penetration of sweat, so change or wash them regularly to keep them absorbent and dry.

3.Anti-state sweatbands can not only prevent the loss of sweat, but also play a role in sweat absorption, protect the head, relieve headaches, etc., so in sports, the role of sweatbands should not be underestimated.

Conclusion Sweatbands are very necessary for playing badminton and other sports, not only to keep the head dry, but also to relieve headaches and prevent problems such as colds and colds. Remember to choose the right sweatband, wrap it properly, and take care to keep it dry and clean to get the most out of it.

Hello, I am happy to serve you and make a wise answer for you: badminton sweatbands are generally available in equal widths. The wider the width, the better the sweat absorption, but it will also be heavier and not conducive to exercise.

It is generally recommended to choose a wide range of sweatbands. When using a badminton sweatband, you may encounter the problem of slipping, the main reason is that the width of the badminton sweatband is not wide enough to hold the hair in place, or there is too much hair and the width is not enough. The workaround is:

1.If you have too much hair, you can comb your hair first and then put on a sweatband. 2.

Choose a sweatband of the appropriate width, it is generally recommended to choose a sweatband of the appropriate width. 3.After wearing a sweatband, you can fix the hair with your hands first, and then tie the sweatband tightly to better fix the hair.

Personal tips: When choosing a badminton sweatband, you should choose according to your hair width and hair volume, try to choose a sweatband with the right width, and fix your hair before wearing this belt, which can effectively prevent the sweatband from slipping off.

Wrap the back one first, then wrap it spirally forward until it reaches the front, and then tape it on!

Wrap upwards from the tail of the stem, direction: Looking down at the tail of the stem is counterclockwise.

You won't know this, go around it one by one, pay attention to the uniform thickness.

The material of the badminton sweatband is generally made of PU material. Sweatbands of this material tend to smell and slip on the hand, resulting in a lack of power to kill the ball, and they need to be replaced frequently.

The sweatband is used to prevent athletes from being blistered or worn through the skin by the handle of the racket due to excessive hand force or too long.

In addition, the sweat of athletes during the competition is easy to slip when it comes into contact with the cortex, which affects the normal performance of the game. Therefore, athletes often wrap a layer of leather or towel on the outside - this is called a sweatband. With the addition of sweatbands, athletes feel comfortable and soft to hold, and they can absorb sweat themselves, making it an excellent hand protection device.

Generally, it is made of PU material.

I don't approve of using sweatbands for a number of reasons:

1: It is easy to stink.

2: Slippery, resulting in no power to kill the ball.

3: Replace often.

It is recommended to use a special anti-slip liquid with hand glue between 30 and 50 yuan, and the effect of YY brand is good!