HP PC DV2621 Vista for XP Problem

Oh, it's best not to get it yourself, because even if you change the XP system, there will still be a lot of driver problems, because there is no driver for XP, you have to **, but first you have to understand what model of your hardware is, get a good driver, prepare the XP installation disk, you have to uninstall your Vista first, use the installation disk with DOS startup, enter the DOS to format the disk where the Vista system is located, for example, format C: Q Enter.

After waiting for completion, put in the XP installation disk, install it according to the prompts, enter the serial number, and install the prepared drivers after entering the system.

As for the refresh bios you said,,It's recommended that you don't move.,Because if you don't get it right, it's over.。。。 Hehe, the power must not be cut off halfway.

Looking for after-sales such an effect, if you don't look for after-sales, you're too cheap for him.

And it's better to install XP now.

It's best not to pretend to be yourself.

The installation sequence is to enter the BIOS to turn off SATA, then install XP, then install the motherboard driver, then UAA, then other drivers, then SATA driver, and finally enter BIOS to enable SATA.

Oh, two ways to press F12 to select the boot mode when booting up, you can choose Guangqi, you can use the optical disc to install XP If there is no Guangqi, remove the hard disk and hang it on another machine Install a ghost version of XP Finish on your machine.

It's too simple to change the system, your laptop can have an optical drive, just find a computer maintenance place to get a disc, the current system disc is a fool's operation, as long as you know Chinese, you can install it yourself, if you are idle and you let them give you security, it will not be a problem to spend a few dollars. But you said that the blue screen still burns hardware, I don't understand, I also sell HP computers, new computers, yours or vista, the chance of system poisoning is very small, so I think the chance of software causing blue screen is also very small, burning hardware (12 hours of ventilation is OK), you should not find a ** business to understand what is wrong with your computer.

Go to the electronic market and buy an XP disk, and then reinstall the system and you're done.

3.Turn on the computer and press F8 to enter the safe mode to see if there is a problem, if not, it is recommended that you upgrade the antivirus software, check and kill it all; If not, it is recommended that you reinstall the system using the Pure System installation CD.

4.Are you using the ghost version of the system? Don't use the ghost version of the operating system, although the ghost version of the operating system is easy and quick to install, but it is easy to have system problems or drivers that cannot load normally, and your problem is likely to be caused by this problem.

It is recommended that you look for the regular pure installation version of the system installation disc optical drive boot installation to see if it can solve this problem. "

1. Since your computer is designed for the Vista platform when it leaves the factory, the official has not tested the XpP system, and the official has not launched the corresponding XP driver, if you install Xp, there may be some hardware problems that cannot be used normally (such as touchpad, fingerprint and camera equipment can not be used), so it is recommended that you use the Vista system. for optimal performance and stability.

2. Your machine does not publish a handwritten program under XP, so this program is installed and used without rock wheel method under XP.

We hope you find the above reply helpful.

You can use the original system installation CD to perform the following operations; If you are still having problems with your machine after following the steps below, it is recommended that you can try to save important files and reinstall the operating system after formatting the hard rock roulette wheel of the machine

1.Put the Windows installation disc into the CD-ROM drive and set it to boot from the CD.

2.See"press any key to boot from cd or *** …"or "Press any key to boot from disc", quickly press any key on the keyboard.

3.Select "Repair Computer".

4.Select the language, time, region, input method, and click Next.

5.In the System Recovery Options window, tap on "Command Prompt".

6.Type bootrec fixmbr and press enter.

7.Type bootrec fixboot and press enter.

8.Type bootrec rebuildbcd and press enter.

We hope you find the above reply helpful.