Urgent! Computer installation, how to install this computer system? Urgent!

Even if the optical drive is broken, there is no need to be so troublesome, the method you said, in principle, is not possible, because other people's computers are equipped with other people's hardware, and if you take it to use, it will conflict!

You can do this, for example, you are on the Internet ** XP version of a computer company, (if you can't access the Internet, use a USB flash drive to test it) and then unzip it and install it on your own computer, (don't unzip it to a C disk) This is also OK, and this is safer, the installer will automatically restart, and then install the system on the C disk. After installing it, you will back up the ghost again, so that nothing will happen!

If it's the same system, it's okay to ghost, but the hardware of the two computers is different, and some software drivers have to be reinstalled! You can't install it on your laptop first! Because the hardware is different, it is not easy to use the notebook, and the virtual memory does not matter, and there will be no problems on other computers!

1. If the hardware is the same, it can be installed. Otherwise, you can't, because the driver is different, there may be a blue screen, or you can't enter the system. You can place a system online. Install with a hard disk installer. (You can also load it without a CD).

2. The original version of the XP has to be installed with a driver in the current machine, which is nothing bad, and the installation is the same as when installing the system.

3. Virtual memory can be placed on any disk. If you have a large amount of physical memory, you can leave it unset.

This is not possible, the probability of success is about 20%, and it will not succeed regardless of the situation, I will tell you a good way:

You** a ghost xp system and then will. Unzip the GHO file to the hard drive and then go into DOS to recover that with Ghost software. The GHO file is OK to the C drive! @

If your computer and laptop are configured the same, you can do it, but if they are different, you can't use the same ghost.

First of all, it depends on whether you are a laptop or a desktop. If it's a laptop, you just need to insert the system disk into the optical drive and start it again. If you are a desktop, you need to go to the BIOS interface to set it up.

1. The method of entering the BIOS varies according to the type of BIOS, the most commonly used is to press and hold the "DEL" key on boot (there are also press F1, F2, please refer to the manual).

2.The item to set the boot sequence is available in the "Advanced BIOS Features" option.

3.If you want to set the optical drive to the first boot order, you can move the cursor to "first boot drive", then press enter, select "cdrom" with the cursor, and then press enter to confirm.

4.Save and exit, and restart is OK.

There is another way.

Directly insert the system disk into the optical drive, enter the micro system, and then follow the system prompts to install.

Set the first boot as the optical drive, put it in the installation disk, restart, it will be automatically installed, and take out the disk when the computer is restarted

Get it to repair the computer for 10 yuan, the first time I see him install it, the next time I can install it.

Foolish! Next + Wait!

Because cleaning up dust needs to be careful, and the reasons are as follows.

First, you unplug the computer from the fan. Because the fan is also a small generator (in the case of rotation), the voltage base of the computer accessories is only 12 volts at the bottom, and if you blow it to generate electricity, it will generate electricity.

Second, you can't use a hot air blower, otherwise the motherboard resistance will blow and weld.

Third, when the cleaning is completed, you must pay attention to not striking iron when installing accessories, otherwise you will not be optimistic.

Solution: It is recommended that you take all the computer configurations out of the chassis and then make sure that there is no metal conductive object underneath for testing.

Generally solves the problem.

When you clean up, you must have pulled everything you could. For example, have you brushed the memory slot with a brush? If the ash is concentrated there, it will cause poor pin contact.

If you said that the hard drive, data cable, and memory are checked, no problem. And either it's black and still. Or a blue reboot.

I can only give you two words. "Ghost".

It's a new virus that is stored in the MBR of the hard drive. If you are familiar with installing DOS under the disk, then use the DM tool. Fix mbrRe-ghost system. That's it.

Hello friends:

Hope it helps you and I wish you happiness

If you are a novice, I don't recommend using those tutorials on the Internet, it's too troublesome, one wrong step, the computer will break, you can use orange one-click reinstallation to try, you can stabilize the one-click installation system.

[Problem description]:

A solution for system reinstallation.

Easy Steps]:

Solution]:

Step 1: Open the 360 Security Guard version and click the "Functions" button at the top; As shown below:

Step 2: Click the "Add Widget" button to open the widget addition list, find the "System Reinstall Master" and click the "Add" button behind it to add the "System Reinstall Master" componentAs shown below:

Step 3: After adding, the 'System Reinstall Master' will be automatically opened, click the "Start Reinstalling the System" button on the Reinstall Master; As shown below:

Step 4: Wait for the System Reinstallation Master to check whether the current system meets the reinstallation requirements. No action is required at this point, and the detection time is approximately 30 to 40 seconds; As shown below:

Step 5: After the detection is completed, you will be prompted to select the reinstallation type, currently there are two types of reinstallation, "Restore data after reinstallation and one-click installation software (recommended)" and "Pure system reinstallation". In order to avoid unnecessary data loss, it is generally recommended to use the former 'Recover data after reinstallation and one-click installation software (recommended)', and click the "Next" button after selection; As shown below:

Step 7: 'System Reinstallation Master' will list the software that can be kept in your computer, you can choose the important software you need to keep according to your needs, if you are not sure which ones you need to keep, in order to avoid unnecessary software loss, it is recommended that you click the "Select All" button to keep all the software installed in your current system. Once you're done choosing, click the "Next" button.

As shown below: Step 8: Officially start to reinstall the system, the following steps 'System Reinstallation Master' will be completed automatically for you, please wait patientlyAs shown below:

Note: During the reinstallation process, please be sure to follow the prompts of the 'System Reinstallation Master', and do not close the Reinstallation Master and the computer halfway. Unexpected termination may result in unsuccessful system reinstallation or even system failure to boot normally.