When will the third subject be added or subtracted, and what is the prescribed time for the addition

Subject 3 generally starts with first gear, and the vehicle can be changed to second gear when walking, because there is a requirement in subject 3 that the driving distance with first and second gears cannot exceed 500 meters, otherwise it will be judged as unqualified in the exam! When driving in second gear, when the speed is 20 kilometers higher with refueling, you can change to third gear! When the speed exceeds 30 kilometers, you can change to 4th gear, and you can change to 5th gear after 40 kilometers (general subject 3 does not use 5th gear); Of course, when you drive, you can observe the speedometer under the steering wheel (the watch on the right), remember one thing, give a little oil before shifting, so that the speed reaches the speed required by you to change gears, release the accelerator, and then press the clutch pedal to change gears!

After the gear is engaged, slowly lift the clutch pedal, and you can't lift it fast, otherwise the car will shake (10 points will be deducted); Release the clutch pedal and start with the oil. The same principle, when you want to downshift, release the throttle first, click the foot brake, let the speed down, when the speed of the gear is reached, then press the clutch pedal and downshift! Otherwise, if your speed does not match the gear, the engine will shake and cause points to be deducted!

Subject 3, remember to start in first gear, turn in second gear, run the whole process in third gear, and hang in 4th gear in the middle of the road (subject 3 requires 4 gear operation);

This is my experience when I was studying Subject 3, I hope it can help you, thank you!

In each examination room, the assessment order of the test actions is different, but the addition and subtraction are generally assessed on a relatively long straight line distance.

The long straight section in the examination room is added or subtracted.

Subject 3 plus or minus gear, the time is one minute and 30 seconds. The driving distance in the first and second gears cannot exceed 500 meters. Subject 3 exams.

Start in first gear, and when the vehicle walks, you can change to second gear. When driving in second gear, when the speed of the car is 20 kilometers after refueling, you can change to third gear, when the speed is more than 30 kilometers, you can change to 4th gear, and you can change to 5th gear after 40 kilometers (general subject 3 does not use 5th gear). When you turn halfway, you have to refuel from the second gear to the third gear, add to the third gear and lose the throttle, after the turn is completed, the computer will prompt you to reduce to the second gear (in five seconds is the time to complete the action), and then the computer will prompt ** to the third gear, which is also five seconds to complete the gear.

During the test, when the voice prompt is heard to complete the action of adding and subtracting gears, candidates should adjust the gear to 2nd gear, from 2nd gear to 5th gear in turn, and the speed in 5th gear should exceed 40km h, and then lower the gear to 2nd gear in turn. The gear speed should be matched. Be sure to take a look at the dashboard from time to time.

Through the school area, it must be less than 30 miles in three gears, and four gears or more than 30 miles are unqualified. When slowing down, be sure to downshift. When shifting gears, step on the clutch to the end, gear up, release the clutch gas pedal, and release the clutch not too fast to avoid the vehicle shaking.

You can't skip the gear and shift the gear lever. Gear plus and minus skills: No matter whether you add or decrease gears, you must learn to use the clutch to control the speed of the car and control the timing of gear shifts.

When the gear is increased, when the engine speed reaches 2000r min in the current gear, the speed reached by the vehicle is the best time to increase the gear. When downshifting, the speed of the vehicle may not be reduced to the appropriate speed for a while and a half by stepping on the brakes, at this time we can step on the Litong limb combiner, and then reduce the speed to the appropriate speed by stepping on the brakes. In particular, when downshifting, the clutch should be lifted slowly, otherwise it is easy to cause the vehicle to stall or the body to vibrate obviously.

Millions of car purchase subsidies.

Subject 3 should be added or subtracted 1 time.

The whole process of taking the test subject three plus and minus only needs to be carried out once, because the exam is only prescribed once, and if your level is okay, you can have several more times.

If the road section is better, you can add or decrease gears. If there is no success in upgrading, you need to find the right time to add and decrease the gear, you can add and decrease the operation in a good position on the next section, if the whole process is not successful, the exam will fail.

The Module 3 exam requires students to complete at least one gear plus or minus operation during the exam. Generally, each route in the examination room is equipped with at least two road sections suitable for the operation of adding and reducing gears. The trainees need to choose the appropriate road section according to the road conditions to complete the operation.

Some places in this project are not voice broadcasts, and some places have voice broadcasts, the rules are different in different places, we need to pay attention to it, the principle of selection is that the distance between the road sections is long enough, the road is straight enough, and there are few traffic participants.

Gear Operation:

The operation requirements of gear addition and reduction are completed under the premise that the vehicle speed matches the gear, including the step-by-step shift operation from second gear to third gear and then to fourth gear, and the step-by-step gear reduction operation from fourth gear to third gear and then second gear. In some places, you need to add to fifth gear, and you can pick up and sell over-gear. The regulations vary from place to place, so you need to pay attention to them.

Subject 3. There is a time limit and a distance limit for adding and subtracting gears, the time is one minute and thirty seconds, and the distance is 400 meters.

Candidates are required to press the safety officer.

Approaching the body, go around the car (from the left front door backwards), and open the door to get into the car after confirming that it is safe. After getting on the bus, you hear the voice prompt "Please prepare for the test and verify your fingerprint", first adjust the seat to a suitable position for your spine, adjust the inner and outer mirrors, and fasten your seat belt.

Then do the fingerprint verification. The fingerprint scanner is located on the left side of the steering wheel under the air conditioning vents.

There is a time limit and a distance limit, the time is one minute and 30 seconds, and the distance is 400 meters.

Candidates are required to follow the instructions of the safety officer, approach the vehicle, go around the vehicle (from the left front door backwards), and open the door to get on the bus after confirming safety. After getting on the bus, you hear the voice prompt "Please prepare for the test and go for fingerprint verification", first adjust the seat to the appropriate position, adjust the inner and outer mirrors, and fasten the seat belt. Then do the fingerprint verification.

The fingerprint scanner is located on the left side of the steering wheel under the air conditioning vents.

There is no specific time limit, but the operation should be smooth and smooth, and the speed and gear should be well matched, and there should be no bumps.

Subject 3, also known as the road test, is a part of the motor vehicle driver's license assessment, and is the abbreviation of the road driving skills and safe and civilized driving common sense test subjects in the motor vehicle driver test.

The whole process of adding and subtracting the three subjects of the test only needs to be carried out once. If the road section is better, you can add or decrease gears. If there is no successful upshift, you need to find the right time to add or decrease the gear, you can add and decrease the gear in a good position on the next section, if the whole process is not successful, the exam will fail.

When it comes to subject three, I believe that candidates know that the addition and subtraction of subject three should be the most difficult one, so how many times does it take to take the whole process of subject three?

Under normal circumstances, the whole process of adding and subtracting the third gear only needs to be increased once, and if the road section is better, the increase and subtraction can be carried out. If there is no successful upshift, you need to find the right time to add or decrease the gear, you can add and decrease the gear in a good position on the next section, if the whole process is not successful, the exam will fail.

1. When the subject three is in the gear, you must first confirm the surrounding traffic conditions, and then step on the accelerator to speed up, after the speed is raised, immediately release the accelerator and step on the clutch, and then hang the gear, usually the gear is raised from the second gear to the third gear, and then to the fourth gear, and then directly down to the second gear.

2. When the vehicle downshifts, candidates need to step on the brakes first and then slow down, after the speed is reduced, then step on the clutch, and slowly release the clutch after the gear, and stay in the semi-linkage position for a while, and then release it completely.

The whole process must be operated at one time, and do not procrastinate or hesitate. Practice not looking down at gears when shifting gears, and be sure to familiarize yourself with the position of each gear.

Photo by Pacific Automobile Network Q&A).