The computer is a little slow, and after redoing the system, it appears that NTFI SYS cannot be foun

Take the disk partition tool as an example to introduce the specific solution, select Run in the startup item to enter the welcome interface, and click Enter;

Go to the partition selection page, select the first one, and perform a simple system partition;

It shows that a hard disk has been found, select YSE;

The prompt prompts you can set the virtual disk to a system disk and select yes.

Prompt: After restarting, your partition disk will be formatted, select yes;

Reboot and press F2 to set up boot from the hard disk, and then you will enter the ghost installation interface, and you can complete the installation.

There are many possible reasons for this problem, the main reason is that the partition is not well divided, resulting in an error when installing the system, and there may be a problem with the image itself when installing the ghost version, so you can reinstall it after troubleshooting.

If it's a new hard disk, the ghost version of the system is not good, and it often can't be installed.

In your case, you must have used ghost a few times to appear. Or maybe your previous system was the ghost version. Or you forced it to turn off during the installation process and then reinstall it.

There may also be problems when you use the PQ tool or the PM tool to partition.

Solution:Format the C disk with the official version of the system disk and then install it,Or try to format the C disk with PQ again,You can also install a system without Ghost's CD,It's just a little slow,It takes about 50 minutes,Ghost's only 20 minutes OK。

Your computer is not broken, this should be because there is no boot in the C drive of your computer, you can use DOS as a boot and then install the system.

Are you using the ghost version of the system disk?,Some new brand machines.,Especially this one.,The motherboard doesn't support the installation of pirated ghostxp systems.。。

1.Installing the system disk with the full installed version can solve the problem.

2. If you have to install a ghost version, first change the motherboard BIOS-Hard DRVICE hard disk interface to the IDE general interface, and then use the disc to boot into PE to run OneKey, format C disk, or GHOST11, and select *Manually resuming the installation of the gho image can solve the problem. After installation, change the IDE back to the original SATA or **.

The image file cannot be read. Change the disc or the optical drive.

What if the result is still the same after formatting.

There is a problem with your system disk or a problem with the optical drive.

I've encountered this problem.,You format the C disk.,If it doesn't work, try to install the system in another disk.,If it doesn't work, change the system disk.,Most of the current broken system disks are not so easy to use!

It is possible that the quality of your USB flash drive is not good, and there is an error in copying the past GHO files, resulting in interrupted read and write errors. Copy it again, or try a different USB stick.

The scroll bar should roll 12-14 times It may be that the hard disk has bad sectors, you can check if there are any bad sectors, if not, reinstall the system, and solve it at one time.

Close the redundant IDE channel, usually one lap is about the same.

In the device manager, set the main and secondary to none, if there is DMA, then remove the redundant boot items, and use 360 security guard, advanced boot inside.

Leave only one input method,ctfmon and antivirus software will do。

Re: The computer boot is the scroll bar to roll 12-14 circles, into the desktop takes 1 minute, a bit slow, what is the problem! What to do.

Content] The computer appears that the computer boots up is a scroll bar to roll 12-14 circles, and it takes 1 minute to enter the desktop, which is a bit slow, such as turning on the computer when the computer is turned on is a scroll bar to roll 12-14 circles, and it takes 1 minute to enter the desktop, which is a bit slow, often making rookies at a loss, and I don't know how to be good. In practice, everyone will encounter similar problems. I've come across it three times on my computer.

After repeated exploration, I finally found several solutions. Now I dedicate it for the reference of netizens.

First of all, the computer boot is the scroll bar to roll 12-14 times, into the desktop takes 1 minute, a bit slow seems simple.

In fact, sometimes the problem is more complex, involving both hardware and software problems. Therefore, it is necessary to find out the cause first.

No. It's a problem with your computer's settings. You can go next"Super Bunny,"Select the automatic optimization function inside, and you can achieve an ideal boot speed. The exact reason is hard to say literally. You'll know if you've tried it. If you can, you have to give it points.

The number of turns is more than that's in the pre-reading.,P3's computer can also make it turn half a circle.,There's more things in your C drive.,There's also a setting problem.。

Hehe, maybe you have more things in the C drive, or you have more startup projects.

There is also system junk that causes slowness.

There are too many processes for the system to start. Clean it up with 360, leave only the necessary ones, and clean up the useless ones.

Turn off all IDE channels that you don't use (you can turn them off in the BIOS, or you can disable them in the Device Manager).

Check first whether the C disk is installed more.,It's not just a matter of starting the startup item.,If not, use 360+ antivirus software to detect malware or virus Trojans in an all-round way.。。 That's basically it.。。

Because there are too many **inside** and content, it needs to occupy a lot of resources such as CPU and memory when opened, so the computer will become a little slow to sell. This is normal, if your electro brain configuration is high, it will not have any effect, if the configuration is not high, it will feel very stuck.