Hello, please advise, the router has 5 slots and the switch has 10 slots, why can you only bring 4 c

Why do you say you can only bring 4 units?

I said 5, 6 ......7 ......And, of course, there can be no more than 14 wired ones.

You mean with 4 computers? It's all from the router, right?

The switch has 10 slots, in addition to 1 main line slot, which can connect 9 computers, but also needs 9 broadbands, each with its own use, and does not affect each other.

Like you said, is it the case that the switch is plugged into 3 wires, 1 mainline, 1 to the router (the router has 4 computers), and 1 is connected to the other computer, right? If so, you'll have to get another broadband, one for the router and one for your other computer. The ports on the switch are all same-level authenticated, and they cannot share one, and there must be several corresponding ports with several ports.

Got it? In addition, let me add, what is the model series of your switch, and is there a port marked config among the 10 ports? If so, this mouth cannot be used. The subject is a digital in order to be used.

Dizzy,It depends on how much your network bandwidth is.,I've also encountered a display that is connected but just can't go online or what?,That's because the bandwidth is small.,If you want to, you plan to open a web page without ** something, sometimes it has to reach dozens of kb.,There are more computers and the network speed can't reach it, so it's not possible!

The switch can connect to several wireless routers with several network ports.

The switch is connected to the router, and there are two ways to set it up:

The first method: dynamic IP mode.

1. Plug in the router, don't connect the switch first, reset the router (restore the factory);

2. Connect the computer to any LAN port of the router and enter the setting page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the switch to the WAN port of the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router and change the IP address of the router. For example, most router addresses are, we just need to change the router IP address;

2. Turn off the DHCP function of the router in the settings;

3. Finally, connect the network cable from the switch to the LAN port of the router (any one is fine), note that it cannot be the WAN port.

Theoretically, there are a lot, but the key to its smooth operation depends on the carrying capacity of its superiors!

0) This is a typical second-level company, is your line connected? The LAN port of the router is connected to the WAN port of the switch, do you see if it is connected to the right calendar? It's not a chain of states that can be connected casually.

1) I don't think it's a DHCP acquisition problem, the router won't be so stupid that even the DHCP allocation will be wrong.

2) Do you look at the IP, DNS, subnet mask, and gateway of the computer are all correct? Compare it to a computer with internet access. Have you gotten your IP and DNS?

The command is as follows: Start running cmd ipconfig all

3) Netcom will not give you a speed limit for each computer, but there is a total limit, how much bandwidth does your company apply, 1M, 2M, 4M? Book Zhisun.

4) If the bandwidth of the application is very small, such as 4M, it is normal, and the 4M bandwidth is shared by 10 computers, then the network speed will be very slow, and the drop is normal. This is due to a significant bandwidth crunch.

5) If you are applying for a large amount of bandwidth, enough for 10 computers to share, then you have to find other reasons. Is there a speed limit on the router?

6) Is there a problem with the configuration of the router?

In fact, the switch can be plugged in and used.

If you have any questions, please contact us and wish you good luck.

2: Don't use DHCP to set a fixed IP address.

That's it. There is no other reason.

Try setting the IP manually, it should be fine.

This is different from your network cable access method, which can be divided into two types:

Internet access in the LAN (no dial-up, fixed IP Internet access), so wired, all the equipment will be connected under the switch.

The installation is actually relatively simple, as long as the main and secondary routers are clearly distinguished, and the switch is installed under any router.

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access account and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Set the account and key wirelessly, save and log out.

6. Connect a network cable from any LAN port of the main router to the WAN port of the secondary wireless router, and the computer can access the Internet at this time.

7. Reconnect the router as long as the LAN port is changed to sequential, and the other settings are the same as the secondary route settings.