How to unglue the table tennis jacket, how to remove the glue on the front of the table tennis jacke

Degumming Tools: Method.

1. 2. Tools required: glue. Tools required for method 3: bulking agent, a scrapped bank card. Method 3: Jackets are more suitable.

Glue removal situation 1: hand rubbing method.

For this case where the glue layer is very thin, the method used is generally the "hand rubbing method". Start by brushing the glue onto the sponge and then rubbing off the adhesive layer with your fingers, keeping in mind that this method is suitable for thin adhesive layers.

Deglue removal situation 2: hand drag method.

For the rubber that has been poured more than a dozen times, a thick glue layer is often left on the sponge, and in this case it is easiest to remove the glue. Start by applying glue to the left or right side of the pat, slowly rubbing a layer of glue by hand along the edges. Then you can use your thumb and index finger to pull the glue layer you just rubbed by hand, and you must pay attention to the direction of the pull, the direction is the opposite direction of your wrong glue.

This part can refer to my other article: How to remove glue from table tennis sleeve - detailed explanation of the adhesive sponge removal method. If you find that the adhesive layer is easy to break at this time, you can either try to use one glue removal or try to use three glue removals.

Degumming situation 3: bank card scraping method.

Now there are a lot of inorganic sleeves on the market, such as the recent Hurricane NEO, especially the coat, etc., many friends' coats are damaged by the above two methods, especially those coats with a very thick glue layer, this method can be used at this time.

Inorganic glue can be rubbed off from one corner of the sponge, and then torn off like **.

Organic glue is the same as above, but it is easy to damage the cake sponge, and the damage rate of high-density sponge is low.

There is a method of removing glue, the coat is very easy to use, that is, the electric iron removes the glue, slowly heats it up, so that the glue layer can be softened, and the front end of the electric iron is slowly rubbed, and the glue can be removed. As long as the temperature is handled properly, the sponge will not be damaged.

Summary. 1.Wipe the glass surface clean, apply the glue and apply organic glue 3 times, and each time use a glue brush to cover half of the glue of the brush head.

2.Buckle the glue layer facing down on the glass surface. Wait about a minute in summer and two minutes in winter.

3.When the time is up, uncover the glue, use your index finger to gently push in the middle of the glue, you will find that it is easy to roll up the glue layer to expose the sponge layer, and then slowly and gently spread it around.

4.It should be noted here that the first time to remove the glue may be because of unskilled or fear of damaging the sponge, the glue removal time is longer, in that case, the glue will be dry, if this situation occurs, then continue to brush the glue and then buckle on the glass for a while.

5.Inorganic degumming is relatively easy, just rub it from the corners and slowly peel it off, so I won't say much here. It's just that the inorganic glue on the bottom plate of some golfers is not easy to remove, and the hand rubbing is too tiring and a little painful. You can use a piece of waste anti-rubber surface scissors to rub, which is very effective.

How to remove the glue from the front of the table tennis ball sleeve.

1.Wipe the glass surface clean, apply the glue and apply organic glue 3 times, and each time use a glue brush to cover half of the glue of the brush head.

2.Buckle the glue layer facing down on the glass surface. Wait about a minute in summer and two minutes in winter.

3.When the time is up, uncover the glue, use your index finger to gently push in the middle of the glue, and you will find that the glue layer is rolled up to reveal the sponge layer, and then slowly spread and rubbed around.

4.Here to fight acorn, the first bend reputation may be because of unskilled or afraid of damaging the sponge, the glue removal time is longer, then the glue will become dry, if there is such a situation next to the base, then continue to brush the glue and then buckle on the glass for a while.

5.It is easier to judge stupidity by inorganizing, just rub it from the corner and slowly peel it off. It's just that the inorganic glue on the bottom plate of some golfers is not easy to remove, and the hand rubbing is too tiring and a little painful.

You can use a piece of waste anti-rubber surface scissors to rub, which is very effective.