How to pour the table tennis long glue, the straight shot long glue of the table tennis ball

You can practice the work in your hands well, and if you are proficient, it will be fine.

In the process of hitting the ball, the golfer will use the difference of different rubber on the front and back sides to reverse the board, so as to create different spins, confuse the opponent, and create opportunities for the attack. Generally, it is configured with positive and negative long or positive and negative growth. For example, after the forehand backhand is sent downspin when serving, if the empty banquet limb predicts that the opponent is rubbing back the downspin ball, then turn the shot 180 degrees in advance, so that the forehand becomes a long glue, and the arch of the long rubber is used to squeeze and skim to fight back, and the return ball becomes a spin on the bucket world.

(1) Side-cutting or side-extrusion.

If the ball is topspin, the racket shape is basically vertical, and the side cut is made; The ball is downspin, and the racket shape is slightly up, and the side squeeze is carried out. We should pay attention to hitting the ball during the ascending period and return the ball to the opponent's backhand triangle. When hitting the ball, the racket swings to the left front, which can not only reduce the force appropriately, counteract the momentum of the incoming ball, but also borrow the spin of the opponent's incoming ball.

(2) Force reduction gear.

When we receive the ball, we can appropriately retract the racket back according to the speed, strength and rotation of the opponent's incoming ball, and the landing point of the force reduction block should be controlled in the opponent's forehand near the net short circuit. The main point is: the ball that reduces the force and blocks the short must be low and not out of the table, at least it should be a ball with a half out of the table, otherwise it is better to cut the long straight shot and the long rubber inverted board play.

(3) Flirting.

Our position can be slightly retreated, with the backhand in the early stage of the ball in the early stage of the fall, can not exert a lot of force, especially not too much upward force, so as not to raise the attack. If you catch the downspin, you can send a little more force forward, so that the ball is more floating. Since the opponent usually serves this kind of ball from the backhand position, I can first pick up more straight lines and then be prepared to defend a board.

(4) Bounce.

Long rubber bounce is a very practical offensive technology, the bounce speed is fast, the ball sinks quickly after passing the net, and shaking, floating, low arc, if you add a better landing point control on the side, the lethality is stronger. We should turn the paddle horizontally, and in the rising or high point of the incoming ball, the middle of the topspin ball is hit, the elbow and big arm are relatively fixed, and the small arm and wrist are explosive to the right front; If it's a downspin ball, hit the lower middle of the ball and push more force to the upper right.

(5) Receiving the serve and attacking.

With this kind of connection, the first thing to know is whether the opponent has a high-quality straight run ball with similar movements. If there is, then we should be careful when we take it sideways. The gist of it is:

Concentrate a lot, wait for the opponent's ball to leave the racket at the moment to make a judgment on the direction of the ball's flight, if it is a slash, decisively turn sideways and use seven or eight points of force to half pry and half play a straight line, and then quickly restore, ready for continuous attack.

(6) The inverted plate is pulled with reverse glue.

Pulling is generally used to deal with long balls, and it is necessary to pay attention to the difference between the first time and the second time in the pulling. When the hand is higher than the table or basically on a plane with the table, it can be regarded as the first time, at this time, it is easy to send force, which can ensure a certain accuracy and strive for the initiative in time; The hand is lower than the table to contact the ball, which can generally be regarded as the second time, when contacting the ball, it is necessary to make appropriate adjustments, and at the same time strive to reduce the arc, it is necessary to rely on the landing point to control the opponent's loss.

(7) Straight and horizontal shooting.

It can improve, enrich and develop the backhand technique of straight shooting long rubber backboard play and broaden its ball path. For the opponent's long ball sent to our left corner, we can also use the reverse arc circle technique to enter the "first three boards" scramble stage.

Summary. Dear, I'm glad to answer this question for you, according to my comprehensive analysis, table tennis long rubber playing techniques include: rubbing, skimming, squeezing, cutting, blocking, knocking, scraping, arching, playing, pumping, etc.

1. Rub: with your wrist. Long rubber rubbing balls should be used sparingly, especially taboo continuous application.

2. Apostrophrophe: Hold the racket and lean back, from back to front, from left to right. On the right foot, hit the ball in the ascending phase, and move quickly.

3. Squeeze: Deal with topspin balls. The angle between the racket and the table is about 90°.

I hope it can be helpful to you, and I wish you a happy life. <>

Dear, I'm glad to answer this question for you, according to my comprehensive analysis, table tennis long rubber playing techniques include: rubbing, skimming, squeezing, cutting, blocking, knocking, scraping, arching, playing, pumping, etc. 1. Rubbing:

With the wrist. Long rubber rubbing balls should be used sparingly, especially taboo continuous application. 2. Apostrophe:

Hold the racket backwards and hit the ball from back to front and from left to right. On the right foot, hit the ball in the ascending phase, and move quickly. 3. Squeeze:

Deal with topspin balls. The angle between the racket and the table is about 90°. I hope it can be helpful to you, and I wish you a happy life.

According to my comprehensive analysis, table tennis long rubber playing techniques include: rubbing, skimming, squeezing, chipping, blocking, knocking, scraping, arching, pumping, etc. 1. Rubbing the ball:

With the wrist. Long rubber rubbing balls should be used sparingly, especially taboo continuous application. 2. Skimming:

Hold the racket backwards and hit the ball from back to front and from left to right. On the right foot, hit the ball in the ascending phase, and move quickly. 3. Squeeze the ball:

Deal with topspin balls. The angle between the racket and the table is about 90°. I hope it can be helpful to you, and I wish you a happy life.

According to my comprehensive analysis, table tennis long rubber playing techniques include: rubbing, skimming, squeezing, chipping, blocking, knocking, scraping, arching, pumping, etc. 1. Rubbing the ball:

With the wrist. Long rubber rubbing balls should be used sparingly, especially taboo continuous application. 2. Skimming:

Hold the racket backwards and hit the ball from back to front and from left to right. On the right foot, hit the ball in the ascending phase, and move quickly. I hope it can be helpful to you, and I wish you a happy life.

According to my comprehensive analysis, table tennis long rubber playing techniques include: rubbing, skimming, chipping, blocking, scraping, arching, pumping, etc. Among them, the volley is one of the most important and difficult skills to master.

I hope it can be helpful to you, and I wish you a happy life.