How to change the rubber of the table tennis ball, how to maintain the rubber of the table tennis ba

When replacing the old rubber, it is advisable to follow the diagonal.

If you use too much force or improper direction, it will cause damage to the bottom plate surface or rubber sponge, so you should try to be cautious. In addition, when replacing the old rubber, it is recommended to carefully tear the rubber along the diagonal direction, if the force is too strong or the direction is inappropriate, it will cause damage to the bottom plate surface material or rubber sponge, so you should try to operate with caution. In addition, when replacing the old rubber, it is recommended to carefully tear the rubber along the diagonal direction, if the force is too strong or the direction is inappropriate, it will cause damage to the bottom plate surface material or rubber sponge, so you should try to operate with caution.

In addition, when replacing the old rubber, it is recommended to carefully tear the rubber along the diagonal direction, if the force is too strong or the direction is inappropriate, it will cause damage to the bottom plate surface material or rubber sponge, so you should try to operate with caution.

To maintain the friction of the table tennis ball, you should start to pay attention to it, for example, when you finish playing, if there are stains on the racket, you should gently scrub it with soapy water. In particular, don't use lukewarm water, hot water to wash. Because that would denature the racket. Rubber friction.

As soon as you wash it, it will not come off. Then use a ping-pong racket.

The special film is attached on both sides. Keep in a dry place and make sure there is no water on the racket. Foil included. There can also be no water, otherwise the whole racket will go bad.

After the table tennis racket is used for a period of time, the rubber will age, so we have to replace the table tennis racket with a new rubber. Replacing the rubber is a hassle and time-consuming. Therefore, in addition to a certain amount of technical means, we also need to have a certain amount of patience to make the old racket regain its original power.

Table tennis rubber maintenance method:

1. After playing, use a sponge to wipe the rubber with cleaning liquid, the main purpose is to remove the dust and water vapor on the rubber to avoid the conditions required for oxidation.

2. Paste the protective film after cleaning. When playing, be sure to place the astringent film in a safe place, if it gets dirty, the astringent film will lose its effect.

3. Place a cool and ventilated place, the shady place is mainly to avoid sunlight, and the ventilation place is mainly to avoid the bottom plate from being damp.

The method of maintaining the table tennis rubber is as follows: after each game, moisten it with a sponge, wipe the dust on the surface of the rubber sheet, and then cover it with plastic film, and put the racket into the racket sleeve, so that the surface of the rubber will not be oxidized.

If you change to a new racket, a better one will be more expensive, relatively speaking, it will be more cost-effective to change two good rubbers. Let's share with you how to change the rubber of the table tennis racket.

First of all, we put the things we are going to use in front of us, where we can reach out, table tennis rackets, two new pieces of rubber, special glue for table tennis, knives, rags, etc.

To save time, we can start by applying glue to one of the two new sheets. Pay attention to be even when brushing. Wait until it is dry before brushing, a total of 2 or 3 times.

Next, we will tear off the old rubber on the table tennis racket, there will be a sponge under the rubber, which is more difficult to clean, we can use a knife to cut off along the edge, and use a knife to cut off the residue after tearing it off. After getting the forehand right, tear the rubber of the backhand.

Brush the wooden board with special glue for table tennis, brush it evenly, and brush the glue again after drying, 2 or 3 times. When brushing the glue, find that the remaining sponge is cleaned up in time, so as not to stick to the new rubber will be uneven and affect the use.

When waiting for the rubber and planks to dry, we can clean up the sponge debris to the point, and there is no debris for easy operation.

After the rubber and board are brushed 2 or 3 times and the glue has dried, we brush again to glue the board and the new rubber together, pressing it once along the outer edge with our thumb. If there are some parts that can't be sticky when sticky, you can press it on it at noon, such as a water cup.