xp How to use 1 network cable to form a LAN with 2 computers under xp

Make a network cable, one end: orange-white, orange, green-white, blue, blue-white, green, brown-white, brown-white;

The other end: green-white, green, orange-white, blue, blue-white, orange, brown-white, brown-white.

Just connect the two computers and you're good to go.

If you want to surf the Internet, one of the computers should be installed with two network cards, one network card is connected to the cat, and the other network card is connected to another computer. Then set the IP of the two computers respectively, if you want to go online, you will add a question, I will introduce the same method of two computers to access the Internet at the same time, no need to buy another switch or router.

If you don't have access to the Internet, you can make a cross line to connect it.

As long as you make the network cable an anti-cross line, it is enough.

One head 586a and one head 586b

If you can't do it, you can let me do it for you.

It's just that someone else who connects the two computers will know.

Once the cable is connected, it can be used on the local area network.

As for how to access and how to share, I don't need to say.

Just connect the two machines with a single network cable.

Set them up in a workgroup.

Just sell a switch, the network is connected to the switch, and other machines are also connected to the switch.

Then set up a working group, share the network, set the IP address of the host, and all the others are automatically obtained

Docking. Set up a workgroup.

Files can be transferred.

Buy a land gamer and go home and ask how to use it

Connecting two machines with a network cable is a local area network, and now network operators limit two machines to share one network.

The network cable is connected to form a crossover line. The settings for two computers to be directly connected via a network cable (i.e. peer-to-peer).

As mentioned above, when two computers are connected through a network cable, the connection between the RJ45 network cable plug and the network cable is: one end is connected according to the T568A line, and the other end is connected according to the T568B line, and then the network cable is broadcast into the network cable socket to be connected to the computer through the RJ45 plug, which completes the physical connection between the two computers. However, in this case, data transfer between the two computers may not be immediately available, and the relevant settings must be made

2.Set the subnet mask for each computer to:

3.Set the gateway the same for each computer: for example, if the IP address of the first computer is and the IP address of the second computer is , then the gateways of the first computer and the second computer should be either or both , or the gateway takes any value in between, for example, the gateway of both computers is taken.

4.Set the hard disk you want to access your computer to share: Set up sharing in the same way as you do on a local area network.

After completing the settings of items 1-4 above, you can see the computers connected to each other in the "Internet Neighbors" of the computer, and then you can use "copy and paste" to transfer data to each other like a local area network. In fact, the network cable connection method is so simple, you can also learn to make network cables and become a network expert. Refer to the network cable connection:

Detailed network cable production.

The two computers are directly connected with a network cable, which is considered a local area network 0 0

Hit a crossed line.

One end line sequence is: orange-white, orange, green-white, blue, blue-white, green, brown-white, brown-white.

The other line sequence is: green-white, green, orange-white, blue, blue-white, orange, brown-white, brown-white.

First of all, you can use a router to achieve sharing; Secondly, one of them can be installed as a dual network card to achieve shared Internet access.

Make a network cable, change the order of the wire head, I forgot the order, you check it.

Shared Internet Access Shared Internet access.

Is the network cable that can access the Internet connected from the router or adsl?

The desktop is the host, and the laptop can be shared through the host to access the Internet.

It's very simple, buy a wireless router, 70 to 80 on the Internet, and automatically connect to the Internet, the laptop can be wireless Internet access in any corner of the house, and the two machines can be used together!

The best way is to switch to a router, if you have to use a switch. Add a network card. Sharing a network card to access the Internet, this trouble is not recommended to use.

2. Share the local connection of A2 (it is best to use XP's "Set up a home or small office network" to set up, because sometimes you need to operate the routing table on A, which is very troublesome.) Select the first option when selecting the connection method. )

3. Use "Set up a home or small office network" on B, and select the second option when selecting the connection. You should be able to find the shared connection of A2, and it's OK after clicking on it.

Configured as 2 computers to connect, operating system XP, host dual network card, slave single network card host dual network card, one connected to the local area network, called local connection, one connected to ADSL network cable, called local connection 2, configure local connection 2:

Set the interner attribute to : IP and DNS are automatically obtained

Configure local connection: Internet property settings:

The IP address can be set to.

The subnet mask can be set to.

The default gateway is not specified.

DNS can be set to AND.

Set the dial-up connection properties, in this case adsl:

In the advanced properties, select Internet connection sharing, select the following three options, at least one can be selected, select local connection for home network connection, that is, the connection of the network card connected to the local area network, and set the Internet attribute of the slave.

The IP address can be set to.

The subnet mask can be set to.

The default gateway is set to.

dns set.

Restart the computer as you need to share the Internet.

Note: If you select all three options for Internet connection sharing, the slave may be automatically connected to the Internet after restarting.

Haha, it's not that simple!? On that machine with your dual network card (XP system?) ), just share the network card that is going to provide Internet access for another machine.

I used to do this when I was in my dorm room. It's the "Advanced" tab in the local connection properties.

Use a router to achieve multi-terminal Internet access.

The machine with dual network cards is used as a **server, and it is OK to connect it with a network cable

**The server can be implemented in a variety of ways, such as installing CCPoxy Sygate Wingate or using XP's built-in sharing.

There are two kinds of twisted pair network cables, one is a direct wire, and the other is a cross wire (also called a parallel line).

The line sequence of the crystal head at both ends of the network cable of the direct connection line is exactly the same, but the cross line is different.

Direct wires are used to link between different types of network ports, while cross lines are used for the same type of network port connections.

Specifically, if the two parties to the connection are not in equal status, use a direct connection, such as a computer connected to a router or switch.

If the two connected devices are equal, then use a crossover line, for example, the computer is connected to the computer, however, the network port of many devices is now designed to be adaptive, and the network port that needs to be connected with a crossover line can also work normally with a direct connection.

There are two standards for the line sequence of the crystal head, that is, the practice of 568A and 568B crossing lines: one end adopts the 568A standard, and the other end uses the 568B standard parallel line: both ends are 568A standard or 568B standard, (generally the practice of 568B parallel lines is used).

568A Standard: Green White, Green, Orange White, Blue, Blue White, Orange, Brown White, Brown 568B Standard: Orange White, Orange, Green White, Blue, Blue White, Green, Brown White, Brown.

One network cable, one end press White Orange White Orange White Green Green White Brown Brown, the other end White Orange White Orange Orchid White Green Orange White Brown Brown, and then the IP address of the network card is set to adjacent, such as one is, the other is, the subnet mask is.

It is not possible to use a general network cable, you have to use a crossover network cable, which is the kind of direct network cable.