How can the computer connect to 2 TVs, high scores!

Tell you a very simple solution,If your TV only has a CCTV interface,No other interface,Then throw that TV,Buy a new one,Don't believe what computer signal can be solved into a CCTV signal。 It's not impossible to do that, our unit is doing it, centralize the signals of all cameras and transmit them, and then use the TV to receive, but the cost is enough for you to buy 4 new TVs (you need an image encoding card, an image integration card, a frequency divider, a signal transmitter, and they are all expensive).

Suggestion,Change two TVs with VGA output,Use an RGB splitter,It's the kind of 1 point three,Buy it on the computer market,Just ask the boss,Is there a RGB distributor,Want 1 point 3,You can definitely buy it,Then connect the output of the computer graphics card to the in of the RGB distributor,Then connect the 3 out of the RGB distributor to the computer monitor and two TVs respectively,OK。

Need to purchase equipment: two TVs (with VGA interface), 1 RGB splitter (1 point 3), 2 RGB cables (a total of 4 are needed, but the computer itself has one, and the RGB splitter has one, so you need to buy two).

Spend dozens of dollars to buy a second-hand cheap graphics card with S terminal,Then buy a cable with S terminal to connect to the TV,But the TV must support the S terminal。 There can also be a connector that converts the S terminal to VCD,It must be able to solve on a TV without an S terminal。

Well, I am also using a desktop computer (with a network cable), a laptop (wireless) and IPTV at the same time.

When broadband has IPTV service, it is said that it will send you a new cat, which is equipped with IPTV interface and wireless routing function, and one can get all three of your devices.

If not, you can connect the network cable of the cat output to the switch first, and then connect to the set-top box and the router with wireless through the switch respectively.

The reason for entering the route from IE and changing the local IP of the route to 254 instead of 1 is to prevent possible IP conflicts). Then set the automatic dialing and wireless function on the router, and you're good to go.

Both computers can be set to a fixed IP (5 10 is recommended, if the laptop may be used elsewhere, use the automatic IP), the gateway and DNS are set.

1 first connect the switch with the network incoming cable, 2 switch out of 2 network cables, 1 to connect to the TV, the other to connect to the LAN port of the router, 3 and then from the right to the computer.

Set up automatic dialing and wireless functions on the router, you can connect the network cable output of the cat to the switch first, and you can get all the multiple stations in one place.

Install a wireless router at home, connect two computers with network cables, and the TV generally has a built-in wifi function, which can directly receive the wireless signal of the router.

When three devices are used at the same time, the broadband at home must have sufficient traffic, generally more than 20m.

Adjust the signal input method of the TV.

There is a remote control on the TV with signal input. Just pick it out. If your TV doesn't have one. Then you can't put it.

Whether your TV is a CRT TV or an LCD TV,As long as there is a VGA interface,Fifteen pins,You can connect to the TV,First of all, the resolution of the computer should be lowered to800*600,Some TV resolutions cannot be displayed if they do not meet the requirements,If it is a notebook, you have to switch the display mode。

When the picture comes out, you try to increase the resolution again to achieve the best image quality.

You can connect it with VGA now,LCD TV has a VGA interface behind it,Use VGA cable to connect the computer TV,To put it in layman's terms, the TV is connected as a computer monitor,Then the remote control is selected:Signal source-VGAon。

To connect a TV, please:

Connect the TV to a power source and turn it on.

To activate the TV display, please

Restart your PC:

Then click "Start", "Settings", "Control Panel", then double-click "Display" in the "Settings" tab, click "Advanced".

On the Displays tab, activate TV output.

Open Display in Control Panel, tap the Settings tab, and then tap Advanced to set your TV as your primary display.

Optional: Connect your computer's audio output jack to the TV audio input using an audio cable.