There was a problem with the computer splitting and installing the system 50

1. Wait patiently, some computer configuration problems, the first reinstallation will take a long time.

2. If it doesn't work after no result, then you need to reinstall it again and change the system image. You can use other tools to make a USB flash drive, start the disk, and reinstall the system again.

3. If it still doesn't work, it may be a problem with the hard disk, consider saving the backup data, repartitioning and installing the system again. If it still doesn't work, it is likely to be the cause of the hardware problem, and the hardware problem is recommended to be repaired.

Possible causes and solutions:

1. The system file is too large and it takes a certain amount of time to install.

Reading the system installation information is slow, so you can complete it after waiting patiently.

Second, the reading of the installation information is stuck.

You can continue to wait for the installation to complete or force restart the computer and reinstall it again with a smaller system image.

3. The computer hard disk has bad sectors.

If it is caused by bad sectors on the hard disk of the computer, you can force quit the installation, then restart the computer, enter the PE system that comes with the USB flash drive system disk, use the DiskGenius tool to detect and repair the bad sectors, and then install the system.

Fourth, the system file is missing.

Reinstall it and try it, if it still doesn't work, try it on a different system installation disk.

In this case, the disk can be repartitioned with disk management software, and if it is solid, it needs to be 4k aligned.

You need to delete a partition, and that partition is responsible for repairing the system, deleting it first and then repartitioning it.

Lenovo computers have a hidden partition that can be found and formatted in order to install a new system.

Check whether the hard disk is damaged, whether the partition table is correct, and try to change the USB flash drive to PE.

There is no hard disk option to restore partition when the system is installed on a USB disk, and there are generally two reasons:

In the first case, the SATA controller mode is set to AHCI in the BIOS, and the computer is booted with an older PE system that does not support AHCI. At this time, the PE system cannot detect the hard disk, and of course, the hard disk partition cannot be selected when the ghost restores the system.

In this case, go to the BIOS and set the SATA controller mode to IDE mode.

In the second case, if you use the new version of the PE system that supports AHCI, or you have set the SATA controller mode in the BIOS to IDE mode, the PE system can detect the hard disk and partition normally, but Ghost still prompts that the hard disk partition cannot be found. The reason for this situation is that the disk partition table is GPT type, and Ghost cannot read the GPT partition table properly.

In this case, use the PE integrated DiskGenius to quickly partition the hard disk and convert the partition table to the MBR type, and the hard disk partition can be displayed in Ghost normally.

Redo it more than once, and the partitioned table will occasionally die.

You set up the system first and move all your data to the last plate.

After that, right-click on the My Computer icon, click "Manage", then "Disk Management", in the disk length bar at the bottom right, select the blank disk you want to change, select "Delete Volume", and then select "New Volume".

Or "Expand Volume" on the C drive, compress a blank volume, and then select "New Volume".

The U disk is the system, and the U disk is easy to be infected with viruses.

If there is a problem, rule it out, is there a problem with installing the target hard drive? Or is there something wrong with your USB flash drive.

Did you format the system before installing it? After formatting, it should be 4k aligned, then partitioned, and then installed the system.

This is not a hint of partition failure at all. It was a failure to get the partition. The reason is very clear, there is a lack of drivers, and the solution is to replace them with drivers.

Restart the phone, generally in the phone can still be found, if there is still not, it is because of the sudden unplugging of the USB drive when transferring data, the data file is damaged, but it will not be all damaged.

What system do you want to install?,If the hard disk is set to UEFI mode under PE,Then the hard disk will definitely not be recognized,You need to change it to IDE mode.,So,It is recommended that you change the hard disk mode first.。

Go to the computer city to buy a pirated XP installation disk, set the optical drive to start, and then quickly press the spacebar in the pop-up interface, and then choose to run the DOS toolbox, which has a partition scanning repair program, which is very simple!!

Didn't you set up an active partition?