How do I clean the flannel headphone pads? How to clean the headphone jack dust

Makeup brushes, yes, makeup brushes, soft bristle makeup brushes for girls' makeup, can also be used to clean the dust of the headphone port, which is very convenient. It can also be used to clean the computer keyboard, if your headphones are white, and then for a long time, does it feel as white and shiny as when you just bought it, at this time take an eraser, wipe the black place, and then wipe the headphones with a cloth stained with alcohol, you can be as clean as when you first bought it, the toothpaste itself has a whitening effect, use the toothpaste dipped in water and then gently wipe it with a soft cloth along the headphone cable, pay attention to wipe it twice with a semi-wet towel after cleaning, and the action must be light, Otherwise, the earphone cable will easily break.

Prepare alcohol, which is generally fine, and there are no special concentration restrictions. Prepare to dip a cotton cloth in alcohol, and carefully wipe all the thin wires of the earphones first, usually twice. Gently wipe the left earbud and wipe it repeatedly until it returns to its original white color.

Gently rub the thick line and the rest of the remaining area, damping it with alcohol. The easiest way is to directly use a small cotton swab dipped in alcohol to scrub the shell of the earphone, but there is a little bit of a bad thing, scrubbing with a small cotton swab will not only leave more cotton wool in the earphone membrane, but also easy to damage the omentum of the earphone, find a toothbrush with soft bristles, and gently clean the surface of the earphone omentum, which can remove the dirt inside the earphone speaker, but do not use a toothpick.

Cleansing water, even if it is a white headphone, can be cleaned with makeup remover, just wipe it with a cotton pad dipped in makeup remover. Find a tube of white toothpaste, squeeze out some, use a tissue or a small towel to dip the toothpaste and wipe the earphones, and it will give you a clean earphone in minutes.

If the headphone jack is a mesh type, take off the rubber cover on the outside and wipe it clean. Rub the mesh again with a toothpick. That's it.

If the headphone jack is not mesh, take off the rubber case and wipe it clean, then wrap a little cotton swab on the head of a toothpick, or a paper towel, and reach into the earphone jack to wipe.

Squeeze out a little toothpaste mixed with a small amount of water, then take a small amount with a cotton cloth and wipe it off with a dry towel. (This wash is still a little fragrant, note that the interface can not be cleaned), this method of cleaning is better, but can be used occasionally, toothpaste cleaning is a compromise way, although it is still corrosive, but compared to the strong detergent is still a lot more reliable.

Moisten the cotton pad first and wipe the earphone cable a few times! Although this method has a low cleaning effect, it can be used frequently. Cotton pads are the least risky way to clean, and as long as the earbuds aren't too dirty, most of the time they can be handled.

Laundry soap can also be used to clean the data cable and earphone cable, cut a small piece of laundry soap and melt it with warm water, then wipe the ear cable and data cable with a small amount of solution dipped in a cotton cloth, and finally dry it with a dry towel. (Of course, dish soap, shower gel, etc. are OK, so I won't give examples one by one, note that the interface can't be cleaned).

When we clean the headphones, the water we commonly use is also the culprit that causes the aging of the cable. The water we currently use is not purely neutral, so try to minimize the number of times you rinse with water. In the long run, the wire will become stiff.

It should be noted that the cleaned earphones should never be placed around the heater to dry, as the temperature of the heating will directly deform the cable skin.

In order to minimize the damage, the material of the towel should be as soft as possible, and do not wipe the earphone cable too hard.

1. Prepare a roll of double-sided tape and a toothpick, and tear off a piece of double-sided tape to wrap the toothpick. Don't wrap it too thickly, because the headphone jack is not very large, and if it is too thick, it will probably cause some corners of the headphone jack to not be cleaned properly.

2. Insert a toothpick wrapped in double-sided tape into the earphone hole, without too much force. Pay attention to the small corners in the headphone jack and try to achieve the best cleaning effect.

3. After the cleaning is completed, you can see that there is a lot of dust stuck to the toothpick, and the cleaning effect is very ideal.

4. After the cleaning is completed, you can also use the dust plug to reduce the dust entering the headphone jack.