How do I clean my computer keyboard? How do I clean my keyboard?

Wash your keyboard thoroughly.

The keyboard is our most commonly used computer input device, and if the keys are not flexible, greasy, and the light press does not work, it will bring a lot of trouble to the operation of your work computer. In addition, if the keys are not cleaned frequently, they can become a source of infection for many infectious diseases. It can be seen how important the cleaning of the keyboard is.

However, due to the large number of keyboard keys and complex structure, many people cannot correctly master the cleaning method of the keyboard.

1 First turn the keyboard upside down and shake it gently, then you will notice that confetti, hair, food scraps and other debris fall out of the gap between the keys of the keyboard.

2. Take out the vacuum cleaner to remove the dust from the surface of the keyboard. Then use high-pressure air sprinkler irrigation to remove the debris in the cracks of the buttons; The side of each keycap of the keyboard, close to the bottom of the keycap, is not easy to clean, so you can use a cotton swab or chopsticks wrapped in cotton to dip a little detergent and wipe them one by one along the direction of the gap. Be careful not to get too much detergent on it, and don't wash it with water.

3 Finally, wipe the plastic shell and keycap surface of the keyboard with a rag.

Draw out the layout of the keyboard keys to avoid installation errors after disassembly;

Remove all the keycaps. Pay attention to the dismantling, the force should be even, do not use brute force. Pay special attention to the Enter key, shift key, "ins key" and "+ key" in the keypad area, they are fixed with iron hooks under the keycaps due to the large size of the keys, and do not pull the iron hook too hard to deform when dismantling.

In particular, the enter key in the main keyboard area is fixed with two iron hooks under it, and it cannot be pulled hard when removed. There is a small spring underneath the spacebar, be careful not to lose it when disassembling it.

Once all the keycaps are removed, you can see the clutter hidden inside the keyboard. After the author's keyboard was removed, it was found that there was a lot of dust, fluff, hair, as well as melon seed skin, drink stains, etc. Take a brush to clean these debris first, and then use a rag dipped in water to wring it out to wipe it, and for those sticky stains, you can use a rag dipped in some cleaning solution to wipe it.

The keycaps can be cleaned one by one with a rag, but more than 100 keys are wiped one by one, which requires a certain amount of time and patience.

After all the scrubs have been made, let the parts air dry before you can install them. The installation of the keyboard can be completed by following the layout diagram drawn earlier. The same as when dismantling, the force should not be too strong, it should be evenly forced, and the keys with iron hooks under the enter key should be hung up first, and then the keycaps should be installed.

Be careful not to install a few arrow keys in the wrong position, and do not confuse the number keys in the keypad area with the number keys in the large keyboard area (the number of the number keys in the keypad area is marked above the keys). The cleaned keyboard will look brand new, and using the cleaned keyboard to work may inspire you more.

Hope it solves your problem.

Buy a kind of keyboard cleaning glue, clean it is simple and troublesome and can be used many times, if you don't use glue, you want to pry out the keys of the keyboard and it is easy to pry it out.

It can also clean the keyboard, and it can decompress, which is comfortable.

Here's how I do it: but I'm more hands-on and don't know if you can't!

Remove all the keycaps from the keyboard (with a hairpin or something, and then put the keycaps in a laundry bag (or a net pocket if you don't have one) and put them in the washing machine to wash with your clothes. Clean the surface of the keyboard with a damp cloth and a brush, wipe it with a cleaning solution (a small amount of soapy water, etc. stuck to the cloth) appropriately, and finally install it.

Unscrew the screws on the back of the keyboard, you can remove each keyboard key, put it in warm laundry detergent water to clean it, and reinstall it, I have washed it several times.

First, unscrew the screws on the back of the keyboard with a screwdriver, place the keyboard face up on the table, and gently uncover the panel, we will see a bunch of small rubber pads, and when you see it, you will understand why each key is elastic. Then, take out these small rubber pads and wipe them one by one, and then put the keyboard panel in warm water with dish soap at home and soak it for a while before scrubbing it clean. Finally, brush all directions with a soft-bristled brush, and the panel will be clean.

The circuit board is generally not too dirty, just wipe it with a clean soft cloth.

Once the cleaning is complete, allow the cleaned keyboard to dry for a few hours or use a hair dryer to dry, then install the keyboard as it is. When installing, you should first put the panel facing down on the table, put the two sides with book pads, and then put the small rubber pads into the buttons one by one, then put the circuit board and bottom panel, and finally put the screws, and then you are done.

What do you need to pay attention to when cleaning your computer keyboard?

When we use a computer, it is natural that we touch the keyboard directly with our fingers. If we use the keyboard for a long time without cleaning, it is not only easy for the keyboard to accumulate a lot of dust and bacteria, but also there is the possibility of causing illness due to too many germs on the hands. Therefore, the keyboard should be cleaned regularly, and the following will introduce the simple steps of cleaning and the matters that need to be paid attention to.

1. Open the circuit board. The circuit board is generally made of a film made of soft plastic, which is engraved with key lines, and gently scrubbed twice on the road board with concentrated alcohol cotton. For the line of the failed part of the key, it is necessary to wipe it several times.

2. Disassemble the keyboard. Note that when opening the keyboard, be sure that the buttons are facing down and the circuit board is up, otherwise the conductive plastic on each key will fall off one after another, causing trouble for your repair.

3. Remove the dirt in the inner corners of the keyboard. Tools can be brushes, small brushes, etc., but be careful to move gently.

4. Check the conductive plastic of the failed part of the key. If there is a large amount of dirt on the surface, use alcohol scrubbing as well. Assuming that the conductive plastic is damaged, it is recommended that the conductive plastic on the infrequently used keys can be replaced with the damaged part, and the keys can be used temporarily.

5. Check whether the welding module has virtual soldering or desoldering. If you use an electric soldering iron, you can do a repair soldering work. Once the alcohol has evaporated, you can install the keyboard.

First of all, the keyboard is very easy to clean, a simple brush can be done in a few minutes, and a complex brush and alcohol can be done in a few minutes. But we should maintain good keyboard usage habits, and it is best to do it without cleaning up, and the keyboard is still spotless.

First of all, I can't do without a computer for my work, and so far, I have been using my desktop computer keyboard for almost 8 years, and the color is still the same. However, it was repaired once in the middle of the process, and there was no major problem. Let's talk about my habits of using the keyboard, and how to clean the keyboard, and even keep the keyboard clean without cleaning.

Clause. First, let's talk about how to clean up: because the keyboard has a light touch film, so the keyboard must not use brute force in the process of use or cleaning, violent law enforcement, the action should be gentle, gently sweep off the dust on it with a small brush, if you want to thoroughly clean the stains on it, you can consider using alcohol to wash it.

But remember that you must not use clean water, otherwise it will damage the keyboard.

Clause. 2. Develop good keyboard habits: The quality of habits will directly affect the service life of the keyboard or computer.

If you get used to it well, you can use it for ten or eight years, and if you don't get used to it, you will die early. For example, on weekdays, don't put clutter on the keyboard; It is best not to eat snacks or drink water near the keyboard; Place the computer in a place with less dust; If you are away from home, or if you don't use your computer, you can consider keeping your computer and keyboard sealed.

So in the end: washing the keyboard is a small thing, very simple, and not time-consuming. The important thing is to develop good usage habits.

1.First of all, for users who don't have a lot of dust on the keyboard, let's introduce a simple way to clean the surface. This is done by turning the keyboard upside down and gently tapping the back of the keyboard.

The purpose of this is to let both dust and dirt fall out. If there is a lot of dust on the surface, we can knock it back and forth a few times, and then we can completely remove the dust on the surface.

2.If you haven't been using the keyboard for a long time, then we need to wipe the surface of the keyboard to clean up the dust. It should be noted that before wiping, we need to turn off the computer and unplug it (this is for safety reasons).

Finally, wipe it with a damp, clean rag and you're good to go.

3.If there is a lot of dust, then it will not be clean with a wet rag, at this time we can dip some dish soap or laundry detergent on the rag to wipe. It is important to note that we do not squeeze too much dish soap.

Otherwise, it will easily drip into the keyboard. Also pay attention to the four corners when wiping them, because the four corners are also places where water can easily enter.

4.If it's a keyboard that's been used for a long time, then we'll need to clean it thoroughly. This is done by disassembling the buttons.

We need to unplug the computer and keyboard. Then it's time to start disassembling the keyboard. When disassembling the keyboard, we can use something a little stiffer to warp the keys, and then the keys will be easily removed.

Generally speaking, large buttons are more difficult to disassemble, so you only need to remove the small buttons and wash them. In addition, we need to dry for a while after washing. Wait until it is confirmed to be dry, and then you can install it back.