What is the construction process of car film?

Before the film. Before applying the film, make sure that the working environment is dry and dusty, and cover the necessary areas of the vehicle.

2.Clean. Wash the car glass that needs to be filmed, wipe off the water, and cut the car film into the shape of glass.

3.Stereotypes. The cut film is draped over the outside of the glass and shaped with a heat gun.

1. Clean the car glass. This is the first and most important step in the car film, and whether the glass is clean or not directly affects the subsequent film work. Therefore, it is necessary to first wash the glass and the edges of the glass with water that has a cleaning effect but does not include chemicals, and then wash repeatedly to ensure that they are clean.

Then use a scraper to scrape the glass from the dry side to the wet side, from top to bottom, and wipe the edges with a cloth.

2. Cutting the car film. Tailor the film to the actual size of the glass. Prepare the glass sample of the model in advance, and cut the car film according to the model.

3. The car film is shaped. After the film is cut, it is covered on the outside of the glass, heated with a heat gun on the part that needs to be shaped, and at the same time, the car film is tightly attached to the glass with a scraper.

4. Paste the car film. After the car film is set, stick it on the inside of the glass, tear off the car film liner, when the liner is completely removed, stick the film on the glass, and adjust the length of the left and right sides so as not to touch the car frame. Spray water onto the back of the membrane, scrape water from top to bottom, center to edge, and dry with a towel.

5. Quality inspection. Check whether it is firmly pasted and whether there are air bubbles between the car film and the glass, etc.

Car film method and steps:

1. Before the film, first of all, we must ensure that the working environment meets the requirements of dryness and less dust, otherwise the dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film.

2. Cover the necessary position of the vehicle, and protect the interior and exterior with a protective cover, if there is no special material, you can also choose plastic wrap.

3. Clean the car glass that needs to be filmed, pay attention to the top and edge of the glass, and then wipe the water.

4. The next step is to cut the car film, pay attention to the size of the car film to match the glass. Spray a little water on the surface of the glass, then adsorb a certain thickness of plastic film to the window, and then draw a pattern according to the edges, the template can be a little more than the glass.

5. When the front and rear windshields are filmed, the baking film also needs to be shaped. Cover the cut car film on the outside of the glass, and then use the heat gun to shape it, this step is also more critical, and it is easy to make mistakes, because the temperature and shaping method of the heat gun have relatively high requirements, otherwise improper use can easily lead to the car film blackening or glass cracking.

Hope it helps!

1.First of all, the car film should be in a clean working environment, and it is best to be dry, with little or no dust.

2.Wash the vehicle ahead of time and then secure it.

3.Clean every window pane, especially the top and edges, which are not easy to clean, and then wipe them dry.

4.Spray a little water on the surface of the glass, then absorb a certain thickness of plastic film on the window, draw a template according to the edges, 3-5 mm more than the glass.

5.The car film is qualitatively baked, but there is a certain range of front and rear windshields. Use a squeegee to attach the car film tightly to the glass.

6.After the car film is finalized, it will officially enter the film process.

7.Finally, during the flushing process, spray some water or window film installation fluid on the surface of the car film.

8.The film application step is basically completed here, but it still needs to be checked in detail to see if there are any air bubbles.

Hello Car film method and steps are as follows:

1. Spread the solar film on the front windshield first, then blow it with a hair dryer to deform it, and smooth the solar film by hand while blowing to make it extend, which can fit the curvature of the glass;

2. Use a special tool to scrape the solar film flat, so that the film completely fits the front windshield. Use a knife to cut the film into the desired shape, and then remove the various annual inspection signs pasted on the windshield;

3. Gently take off the film that has been extended and cut the shape, spray the mixture of water and washing spirit on the front windshield, and then wipe all the dirty things on the glass clean, and then spray the mixture of water and washing spirit after wiping it clean;

4. Tear off the adhesive and gently stick the film on the glass stained with water and washing spirit mixture according to the shape cut before. Use a tool to expel all the water and bubbles between the solar film and the glass.