Problems with a laptop setting up a WIFI hotspot 50

Maybe there are too many people linked, and the transmitting power of the router is only so large, you are squeezed out. You can wait and try to connect again.

It may be caused by the instability of the company's hotspots.

There could be a few reasons why your laptop is connected to a hotspot but can't get online. Here are some common issues and workarounds: Confirm that the hotspot connection is successful:

Before connecting to the hotspot, you need to confirm that the hotspot is connected to the network. You can try connecting the same hotspot with a different device to check if the hotspot is available. Check the wireless connection:

If the hotspot is connected to the network, but the laptop can't get online, there may be an issue with the wireless connection between the laptop and the hotspot. You can try restarting your laptop and quickly enable and disable Wi-Fi in your laptop. This can sometimes fix wireless connection issues.

You can try changing your laptop's IP address to a different address and reconnecting the hotspot to verify that this resolves the issue. Check for firewalls and security software: If you have a firewall and other security software installed on your laptop, it may block your network connection.

You can temporarily disable these security software, then reconnect to the hotspot and try to access the internet to verify that this resolves the issue. Access restrictions: It is possible that the hotspot settings have made access restrictions, such as blacklist policies or restricted access to certain **.

You can try connecting to other hotspot selling points or changing your internet access method to verify that the problem is on the hotspot side. If none of the above methods solve the problem, it is recommended to contact the appropriate technical support personnel to seek them.

Hello, I've helped you find the results! After the laptop is connected to a hotspot, it cannot access the Internet due to the following reasons:1

The hotspot signal is unstable or the hotspot password is incorrect; 2.The network settings are incorrect, and the network configuration and DNS settings need to be checked. 3.The network connection is blocked due to the setting of firewall or anti-virus software; 4.

There is a problem with the system or network driver fiber reordering. Workarounds include re-entering passwords, checking network settings, turning off firewalls or anti-virus software, updating systems or drivers, and more. Reminder:

When traveling, you must do your own epidemic prevention safety, wear a mask, I hope mine can help you <>

Win10 system can first let the mobile phone turn on the hotspot computer connection, and then disconnect. The computer can be connected to the mobile hotspot and the mobile phone can be connected. It works in person.

It's likely that there is a problem with the wifi module in your mobile phone, I don't know if it's integrated, and the esoteric point is that the wifi IC is broken. The connection time is long, the heating is damaged, and the battery is consumed quickly when the mobile phone is connected to the Internet, do you think it doesn't heat up? The wifi module is very small, you can be sure that your wireless network is no problem, you can try to put your phone close to your wireless router, maybe you can connect to the Internet, be sure to stick to the wireless router. Try it if you don't believe it. If it's connected, the phone is gone.

It should be a matter of setting, and the correct way to set it up is as follows:

1.Start, run, press enter cmd, open the command window;

2.Create a wifi. In the command line window that opens, enter "netshwlan set hostednetwork mode=allow ssid=test key=0123456789", if you don't want to enter it manually, copy this paragraph, and then right-click and paste it in the command line window.

Press Enter to run when the input is complete.

3.Click the network icon in the lower-right corner and select Open Network & Sharing Center in the window that opens.

4.In the Network and Sharing Center window, select Change adapter settings and click Enter.

5.In the window that opens, we see that in addition to the default wireless network connection, a new wireless network connection is added to select the local connection, which is the wireless network connection used to carry the wifi when the local network was just created.

6.Right-click the local connection and select Properties in the pop-up menu window to open the Properties Settings window. Select Share, check the option to allow other users to connect, and click the OK button.

7.Enter the netshwlan start hostednetwork command on the command line, if the bearer network is started, the wifi has been successfully started. On other computers or mobile phones, you can see the wifi named test, enter the password to connect to this wifi to surf the Internet.

8.If you want to end the Wi-Fi, enter "netshwlan stop hostednetwork" in the command line and execute it, and the result shows that the bearer network has been stopped, the Wi-Fi is turned off.

If you have more connections, your phone can connect to the network through the hotspot, and the more traffic you use, the slower the network speed of others.

As long as the AP you set up doesn't have a device connection, it won't matter!

1. (1) Right-click on 'My Computer' and select 'Manage'

The following screen will appear.

2) Select 'Device Manager', and then right-click on the second option in 'Network Adapters', as shown below.

3) Select 'Properties', enter the 'Advanced' option as shown in the following figure (4) Then move the mouse to 'Value', left-click and select 'Disable' or 'Enable', and click 'Confirm'

Turn hotspots on and off.

1) Enter the settings interface.

2) Click on the 'Network & Internet' option.

3) Go to 'Mobile Hotspot'

Click 'Off' or 'On' to turn on and off the hotspot on your computer.

Second, there is also a way to open a hotspot, provided that the computer has opened a hotspot before, and then you can use this shortcut:

1. On the far right of the desktop taskbar.

2. Click on the mobile hotspot marked in the picture above, and the hotspot will be opened after a while.

One, try the 160wifi that drives life, this thief pulls it well.

Second, the Windows 10 operating system supports the virtual WiFi hotspot function, through the following operation settings, the machine with a wireless network card can use the windwos 10 system to set up the WiFi hotspot, so that mobile phones, tablets and other mobile devices can connect to the virtual WiFi network for free.

The specific steps are as follows:

1. Right-click on the start menu, select "Command Prompt (Administrator)(a)", and run cmd Command Prompt as administrator:

2. In the command prompt, enter: netsh wlan set hostednetwork mode=allow ssid=wyd key=12345678, and press enter to execute the command. (Of course, you can also copy the command directly, and then paste Ctrl+V into the command prompt, the ssid is the name of the wireless hotspot display, and the key is of course the password of the wireless hotspot):

3. Then enter system32>netsh wlan start hostednetwork in the prompt

4. Click the network right button on the desktop, and click "Change adapter settings" in the window that comes out

5. Right-click on the WLAN and then click "Properties".

6. After entering the Wi-Fi properties interface, click on the "Share" option, and check "Allow other network users to connect through this computer's Internet connection". Then under "Home Network Connection", select Create Hotspot Virtual NIC (the name of the virtual hotspot NIC is generally Microsoft Managed Network Adapter, in this case, "Local Connection*4").

7. Enter the adapter settings interface to see if the connection has been set up successfully