Decoration, faucet installation and paving sequence

If you want to find a professional plumber and electrician, you can follow the construction drawings if you want to be responsible.

The kitchen cabinet master used chalk to draw the location of the socket cassette and the position of the faucet on the wall. 8.The construction stage, installation stage and furniture soft decoration stage, as shown in the "Schematic Diagram of the Decoration Process" above. One.

In the end, the hydropower is looking for a professional project, which is a hidden project, and it is too much trouble to get it yourself.

Find a plumber to connect faucets, water pipes, switches, and lamps.

Precautions for hydropower installation.

1. Construction drawings before construction, there must be electrical (strong current, weak electricity), water supply and drainage design and construction drawings before construction.

2. It is strictly forbidden to lay the wire directly in the wall, in the floor, under the floor or on the ceiling without any protection.

3. The wiring conduit should be distinguished, and the lines of different voltages, different circuits, and different signals are strictly forbidden to wear in the same conduit.

4. The installation of lamps and lanterns should be carried out after the completion of painting, and the lamps and lanterns should be installed on the brick-concrete structure, and it is strictly forbidden to use wooden wedges, and hooks, bolts or expansion bolts should be applied. There should be no less than 2 bolts (or screws) securing the fixture. Luminaires must not be installed on combustible components.

5. The switch of the lamp and electrical equipment must be installed on the "phase wire" (that is, the control phase wire), otherwise after the switch is dropped, the lamp will be turned off and the electrical equipment will still be electrified, which is easy to cause electric shock.

6. There are two types of protection methods for the power system, grounding protection and zero protection, and China generally adopts the grounding protection mode. Note that in the same system, it is strictly forbidden to take two protection methods at the same time, otherwise it will cause safety accidents.

7. It is forbidden to use the mobile switch at the head of the bed, if the lamp is to use the screw head, the reed tongue of the screw head should be connected to the control phase wire.

8. The interface of each line should be smooth and the connecting plate connection should be firm. The interface box of the power supply inlet box should be protected by a protective ring (lock nut).

9. The arc of the elbow of the threading pipe, in order to update and maintain the wire in the future, the arc of the elbow (i.e., the radius of the cold bending) at the turning point of the threading pipe buried in the wall, underground or ceiling should be 5 10 times the diameter of the threading pipe.

10. It is forbidden to connect the wire in the conduit, that is, if the length of the wire is not enough to be lengthened, the joint of the wire cannot be in the conduit, and it should generally be wired in the junction box such as switches, sockets, and lamp head boxes.

11. The selection of the threading pipe, the threading pipe should choose a certain size (thickness), not only to make the wire penetrate, but also to leave enough gaps, so that the heat generated by the wire when passing through the large current can be dissipated. Generally, the ratio of the cross-sectional area of the wire to the cross-sectional area of the threading pipe is 1 3 1 2. It is strictly forbidden to plug the wire to the threading pipe.

12. Water supply pipe inspection, water supply pipe can use PP-R pipe, copper pipe, water supply pipe must be strictly checked whether the connection part is installed tightly, firmly, and correctly, and then do a hydrostatic test, and the water can be buried after a period of time. The pressure test index is generally suitable.

13. Attention points for the installation of drainage pipes, the horizontal pipes of drainage pipes should have a certain slope, and the socket ports should be tightly connected to ensure that there is no leakage. Fixed pipe brackets, elevator spacing reasonable, firm.

14. The installation position of sanitary appliances should be accurate, and the support and bracket should be installed smoothly and firmly. The floor drain should be installed at a low point in the ground and recessed 5mm into the ground. The connection between the toilet and the ground or the nozzle is sealed with sludge or silica gel, and cement should not be used, as the cement will expand and cause damage to the cracks at the bottom of the toilet.

15. The orientation of the hot and cold water faucet, the hot water faucet in the cold and hot water faucet should be installed on the left side. The electric water heater should have a grounding protection device, and the air in the bile should be excluded when it is first used, and it can be started only after it is filled with water.

We will have our faucet in our home, so that we will be especially convenient for us. Therefore, everyone is certainly familiar with faucets, but they may also be damaged when they are used. So there's a thing of replacement.

Let's take a look at it with usInstall the faucetWhat are the steps? In this way, everyone can come and learn if they don't know. Let's install it very quickly.

1. What are the steps to install the faucet.

1. The first step is to connect the hose to the faucet. Remember to tighten the blow, otherwise it will leak. Optionally, insert the hose into the faucet mouth, tighten it by hand, try to pull it again to see if it is secure, and then attach the other accessories to the faucet.

2. The second step is our fixed faucet, to pass the installed hose through the basin, our attention to the combination of things. Fix it with fittings, try to see if the faucet is tightly connected to the basin and not loose, and then tighten it with screws.

3. The third step is our connection to the water inlet, put the basin in the designated position, and everyone find the right position. Then connect the other end of the hose to the inlet pipe connection. But when taking over, it is necessary to divide the hot and cold water, and remember that the left side is hot water and the right side is cold water.

In this way, the installation of the Liang Pai Qing faucet is completed.

Second, what are the materials of the faucet?

1. The easier to use material is copper faucet, the inside of copper is rougher, but the effect of use is very good, you can observe the inside of the faucet, you can grind deep in an inconspicuous place to see the brass color is no problem, copper is the most suitable material for faucets.

2. There are also ceramic faucets made of very healthy materials, and faucets made of ceramics are also particularly beautiful. Compared with other materials, it has the advantages of no rust, no oxidation, and no easy wear, and the appearance is generous, which sets off the high-end atmosphere of the whole space.

3. There are more rusty steel faucets that are not used by everyone, and stainless steel faucets do not contain lead, acid and alkali resistance, and are not easy to corrode, which is beneficial for long-term use. The hardness and toughness are more than twice as high as that of copper faucets, but the hardness, toughness and cutting are more difficult and costly than copper faucets.

Our faucets are always indispensable in our various places in Heru, so everyone should pay attention to safety when installing. A good installation in this way will ensure our use. You can refer to the above content and use it. This made our installation much smoother.

1. Before installation, it is necessary to check whether the faucet is intact, whether its accessories are ready, and the installation holes need to be cleaned and stared, so as not to affect the later use.

2. Before installation, it is necessary not to let the faucet collide with other hard objects, let alone let cement and glue fall on its surface, so as not to affect the beauty and perception of the faucet and destroy its plating gloss.

3. If it is the first time to install the faucet, before installation, it is necessary to remove the debris in the water pipe, and wait until the water in the pipe is clean water before installing the faucet.

4. In use, it is necessary to open and close slowly, and do not twist it around forcefully.

5. After use, if there are water droplets or stains on its surface, it needs to be wiped clean in time to avoid corrosiveness on its surface.

Nowadays, the faucet will be used at home to receive water, and there are many styles of faucets, and we can buy the cover according to our preferences. In order to save the cost of installation, some people will look at the information to understand how the faucet is installed. So, what are the faucet installation methods?

Let's take a look.

1. What are the installation methods of faucets?

1. First of all, you need to put the hose into the inside of the faucet and connect it, and then quickly connect the screw rod to the interface of the faucet, and put the rubber ring on the faucet. Insert the faucet into the basin, add gaskets and rubber pads, and finally secure the wrench and screws.

2. If the basin faucet is a hot and cold water faucet, then the internal water valve is a three-way and there is only one water inlet, so it can only be connected to one hose. Another hose should be attached to the faucet, but the other section needs to be blocked. The hose of the faucet is only 50 centimeters, but it actually takes about 60 centimeters.

Therefore, it is best to choose a matching 60 cm hose in the hardware store and connect it around the raw material line.

3. After the disassembly and installation of the basin faucet is completed, it is time to clean and glue. To put it simply, it is to close the main gate of water control first, so as to avoid water splashing. Then remove the main water connector as well as the faucet connector.

If the connecting pipe is rusty and difficult to disassemble, use a wrench to unscrew it, and then open the inside of the pipe to complete the disassembly of the faucet.

4. Before disassembling and assembling the faucet, the main gate must be closed first, otherwise it will cause large-scale water leakage. When installing the faucet, the steps are pretty much the same, just reverse the steps, so you must pay more attention.

Summary: What are the installation methods for faucets? I believe everyone has understood it after reading the article. I hope the above content Minxiao can bring you some help and advice. For more information, please continue.

Steps to install the faucet.

1. The axis of changing the faucet knows that the other side can not be defeated, and repairing the faucet is the same. If you want to fix the faucet leakage, you have to understand the reason for the faucet leakage, if it is because the axial gasket in the faucet is worn, then use pliers to loosen the gland bolt, and then take out the axial gasket and replace it with a new one.

2. Tie the faucet tightly when the water-stopping tape is damaged, then use a wrench to remove the anticlockwise rotation of the faucet, and then use the threaded hole to roll the faucet clockwise with wind printing tape for six times, after getting it, re-screw the faucet, and then turn on the switch to try whether there will be water leakage.

3. If the faucet pipe joint leaks, send off the cover nut of the faucet, and then re-tie it tightly, or you can directly replace it with a new U-shaped sealing sock pad.